Search results for " gallium"
showing 7 items of 47 documents
Indium-Gallium Segregation inCuInxGa1−xSe2: AnAb Initio–Based Monte Carlo Study
2010
Thin-film solar cells with ${\mathrm{CuIn}}_{x}{\mathrm{Ga}}_{1\ensuremath{-}x}{\mathrm{Se}}_{2}$ (CIGS) absorber are still far below their efficiency limit, although lab cells already reach 20.1%. One important aspect is the homogeneity of the alloy. Large-scale simulations combining Monte Carlo and density functional calculations show that two phases coexist in thermal equilibrium below room temperature. Only at higher temperatures, CIGS becomes more and more a homogeneous alloy. A larger degree of inhomogeneity for Ga-rich CIGS persists over a wide temperature range, which contributes to the observed low efficiency of Ga-rich CIGS solar cells.
Nanoscale X-Ray Imaging of Spin Dynamics in Yttrium Iron Garnet
2019
Time-resolved scanning transmission x-ray microscopy (TR-STXM) has been used for the direct imaging of spin wave dynamics in thin film yttrium iron garnet (YIG) with spatial resolution in the sub 100 nm range. Application of this x-ray transmission technique to single crystalline garnet films was achieved by extracting a lamella (13x5x0.185 $\mathrm{\mu m^3}$) of liquid phase epitaxy grown YIG thin film out of a gadolinium gallium garnet substrate. Spin waves in the sample were measured along the Damon-Eshbach and backward volume directions of propagation at gigahertz frequencies and with wavelengths in a range between 100~nm and 10~$\mathrm{\mu}$m. The results were compared to theoretical …
Self-focusing in Terbium Gallium Garnet using Z-scan
1998
International audience; When illuminated near its resonance with an Ar ion laser beam (lambda=488 nm), laser induced thermal self-focusing is observed in Terbium Gallium Garnet. The crystal exhibits a strong intensity dependent refractive index change Dn. The Z-scan technique is used to study the beam waist change due to Dn. The refractive index is found to be well described by a quadratic spatial distribution model. Both the sign and the distribution coefficient of Dn are determined.
Indium Selenide Solar Cells
1981
Indium selenide photovoltaic devices are described. Transport and photovoltaic properties are discussed. Efficiencies of 6% are reported and ways of improvement are proposed.
Structural and Electrochemical Analysis of CIGS: Cr Crystalline Nanopowders and Thin Films Deposited onto ITO Substrates
2021
A new approach for the synthesis of nanopowders and thin films of CuInGaSe2 (CIGS) chalcopyrite material doped with different amounts of Cr is presented. The chalcopyrite material CuInxGa1 − xSe2 was doped using Cr to form a new doped chalcopyrite with the structure CuInxCryGa1 − x − ySe2, where x = 0.4 and y = 0.0, 0.1, 0.2, or 0.3. The electrical properties of CuInx CryGa1 − x − ySe2 are highly dependent on the Cr content and results show these materials as promising dopants for the fabrication thin film solar cells. The CIGS nano-precursor powder was initially synthesized via an autoclave method, and then converted into thin films over transparent substrates. Both crystalline precursor p…
Long-transient conoscopic pattern technique
1999
0038-1098; Recent results on laser induced anisotropy in terbium gallium garnet are extended to the dynamic regime. We observed that the characteristic conoscopic pattern formation time presents a quadratic dependence on the beam size. The observed pattern intensity is accounted for by a simple analytical formula. The transient refractive index change due to thermal stress in the terbium gallium garnet is determined. (C) 1999 Elsevier Science Ltd. All rights reserved.
Thin Film CIGS Solar Cells, Photovoltaic Modules, and the Problems of Modeling
2013
Starting from the results regarding a nonvacuum technique to fabricate CIGS thin films for solar cells by means of single-step electrodeposition, we focus on the methodological problems of modeling at cell structure and photovoltaic module levels. As a matter of fact, electrodeposition is known as a practical alternative to costly vacuum-based technologies for semiconductor processing in the photovoltaic device sector, but it can lead to quite different structural and electrical properties. For this reason, a greater effort is required to ensure that the perspectives of the electrical engineer and the material scientist are given an opportunity for a closer comparison and a common language.…