Search results for " interface"

Aqueous nonionic copolymer-functionalized laponite clay. A thermodynamic and spectrophotometric study to characterize its behavior toward an organic …

2006

The affinity of functionalized Laponite clay toward an organic material in the aqueous phase was explored. Functionalization was performed by using triblock copolymers based on ethylene oxide (EO) and propylene oxide (PO) units that are EO(11)PO(16)EO(11) (L35) and PO(8)EO(23)PO(8) (10R5). Phenol (PhOH) was chosen as organic compound, which represents a contaminant prototype. To this purpose, densities and enthalpies of mixing as well as PhOH UV-absorption spectra were determined. The enthalpy and the spectrophotometry revealed PhOH-Laponite interactions whereas the volume did not. It emerged that the area occupied by PhOH on the Laponite surface is equal to that computed from the partial m…

Quantitative XPS analysis of leached layers on optical glasses

1993

The corrosion of optical glasses often reduces the utility of uncoated glasses as well as the adhesion of resistive coatings deposited onto corroded glasses. Photoelectron spectroscopy (XPS) was applied to study glass surfaces with respect to their surface corrosion. In particular, leaching by the influence of polish slurries, pure water, air and even residual gases inside a vacuum device was studied in detail. Pure quartz glass and different sodium and barium silicate glasses were broken in ultrahigh vacuum (4 × 10−10 mbar) for the determination of sensitivity factors of the different XPS signals. It was found that a quantitative determination of the surface composition of corroded and lea…

Volumes of Polar Additives in Aqueous Solutions of the Poly(ethylene oxide)13−Poly(propylene oxide)30− Poly(ethylene oxide)13 Triblock Copolymer at 2…

1999

Density measurements of poly(ethylene oxide)13−poly(propylene oxide)30−poly(ethylene oxide)13 (L64)−water and alcohol−L64−water systems were carried out at 293 and 301 K. The alcohols studied are propanol to pentanol and 2,2,2-trifluoroethanol (F3EtOH) to 2,2,3,3,4,4,4-heptafluorobutanol (F7BuOH). From the experimental data of the water−L64 binary system as functions of L64 concentration (mC), the partial molar volumes of L64 in the standard state and in the aqueous and micellar phases were calculated. At both temperatures L64 micelle is formed by a core of pure polypropylene oxide units and a hydrated shell of poly(ethylene oxide) units. In the case of the ternary systems, the apparent mol…

Fabrication of metal nano-structures using anodic alumina membranes grown in phosphoric acid solution: Tailoring template morphology

2007

Abstract The influence of experimental parameters on the morphology of the porous structure and on the formation kinetics has been investigated for anodic alumina membranes (AAM) grown in aqueous H 3 PO 4 at 160 V. It was found that pore aspect ratio and membrane porosity on the solution-side surface are influenced by tensiostatic charge, bath temperature and the presence of Al 3+ ions in solution. Morphological and kinetic data, recorded in different conditions, give useful information on the growth mechanism of pore channels in phosphoric acid solution. Nickel nano-structures have been fabricated using AAM as template. Electroless deposition, performed by adding the reducing agent to a su…

Micellization and Micellar Structure of a Poly(ethylene oxide)/Poly(propylene oxide)/Poly(ethylene oxide) Triblock Copolymer in Water Solution, As St…

1997

The micellization of the triblock copolymer Pluronic P85 (poly(oxyethylene)27/poly(oxypropylene)39/poly(oxyethylene)27) in aqueous solution was followed vs temperature and addition of aliphatic alcohols, using the spin probe technique. Different types of probes properly chosen (spin-labeled (SL) poly(oxyethylene(4))nonylphenol, SL-Pluronic L62, TEMPO-laurate, TEMPO-hexanoate, CAT 4, CAT 8, CAT 11, CAT 16, and 5-, 7-, 10-, and 12-doxylstearic acids) provided information about the micellar structure (polarity, viscosity, and order degree) at different radial locations. Micellization was found to be low at room temperature, even for 10% aqueous solutions, but strongly increasing with temperatu…

In-situ characterisation of organosilane films formation on aluminium alloys by electrochemical quartz crystal microbalance and in-situ ellipsometry

2005

Abstract Organosilane pre-treatments have been studied intensively during the last years in order to replace hexavalent chromium conversion treatments. The aim of this study is to follow in-situ the formation of this organosilane layer in solution. Two in-situ techniques, spectroscopic ellipsometry and electrochemical quartz crystal microbalance, were used to investigate the mechanism and the kinetics of this protective film formation. In-situ measurements highlight that the organosilane film observed after the drying process is not formed into the solution, but during the emersion and drying step. Hence, it has been possible to characterise the presence of a very thin organosilane layer in…

Composite Thin Film by Hydrogen-Bonding Assembly of Polymer Brush and Poly(vinylpyrrolidone)

2005

Based on hydrogen-bonding layer-by-layer (LBL) assembly in aqueous solution, poly(vinylpyrrolidone) (PVPON) and a spherical polymer brush with a poly(methylsilsesquioxane) (PSQ) core and poly(acrylic acid) (PAA) hair chains were used to fabricate composite multilayer thin films. Hydrogen bonding as the driving force was confirmed by FT-IR spectrometry. A simple method (Filmetric F20) was introduced to determine the thickness and refractive index of the films. The film thickness was found to be a linear function of the number of bilayers. The average increase in thickness per bilayer is 28.3 nm. The film morphology was characterized with scanning electron microscopy and atomic force microsco…

Ellipsometric and fluorescence microscopic investigations of a cyclam derivative at the air/water interface

1993

Thermal and Chemical Stability of Thiol Bonding on Gold Nanostars

2015

The stability of thiol bonding on the surface of star-shaped gold nanoparticles was studied as a function of temperature in water and in a set of biologically relevant conditions. The stability was evaluated by monitoring the release of a model fluorescent dye, Bodipy-thiol (BDP-SH), from gold nanostars (GNSs) cocoated with poly(ethylene glycol) thiol (PEG-SH). The increase in the BDP-SH fluorescence emission, quenched when bound to the GNSs, was exploited to this purpose. A maximum 15% dye release in aqueous solution was found when the bulk temperature of gold nanostars solutions was increased to T = 42 °C, the maximum physiological temperature. This fraction reduces 3-5% for temperatures …

Agent-Oriented Captology for Anthropocentric Systems

2001

Abstract Considering that anthropo centric systems are an adequate domain for captological approaches, and that interface agents are most natural interactants for the humans involved, the paper presents a broad-spectrum generic architectural framework to support developing flexible interfaces for industrial applications, based on synergetic correlation between persuasive technologies and polymorphic agents. The design space for agent-oriented captology is defined and several of its main dimensions are elaborated upon. The main mechanisms used are dynamic priorities, "flexible cloning" and fuzzy temporal windows. Some agent-oriented test-bench applications instantiating the generic architect…