Search results for " low"
showing 10 items of 972 documents
Microwave characterization and modeling of packaged HEMTs by a direct extraction procedure at cryogenic temperatures
2004
In the present work we employ a direct extraction procedure to determine small signal equivalent circuit of microwave GaAs FETs by means of scattering (S-) parameter measurements down to cryogenic temperatures. The direct extraction procedure was tested on packaged AlGaAs/InGaAs HEMTs and good agreement between the simulated and measured S-parameters was obtained at different bias and temperature conditions. We employed a properly designed cryogenic set-up operating in our laboratory that allows to perform DC and RF characterization down to 30 K.
Shear characterization of CaCO3-filled linear low density polyethylene
1988
Shear properties of CaCO3-filled linear low density polyethylene have been determined over a wide range of filler loading. The viscosity rises with the filler loading especially at low shear rates and a yield value appears for CaCO3-contents larger than 5%. The decrease of the die-swell ratios of the filled samples indicates a reduction of the melt elasticity.
Liquid/Liquid Demixing in the System n-Hexane/Narrowly Distributed Linear Polyethylene
2004
Demixing conditions were measured visually for solutions of three narrowly distributed polyethylene samples (M ranging from 6.5 to 380 kg/mol) in n-hexane up to 500 K and 150 bar. This information yields the critical line for infinite molar mass; i.e., it specifies the pT area within which one is safe from phase separation irrespective of the molar mass of the polymer and of the composition of the mixture. The experimental findings are in good qualitative agreement with the predictions of the Sanchez−Lacombe theory applied without any adjustable parameters. The influences of molar masses are, however, underestimated, and the resulting critical compositions are too small. For a more quantita…
Rheological properties and morphology in LLDPE and PC based blends
1990
Abstract During an interlaboratory project on polymer blends (Technical Working Party-Polymer Blends-VAMAS), the rheological characteristics of some samples of blends of polycarbonate with linear low density polyethylene have been evaluated with the aid of a capillary rheometer. Some morphological observations on the extruded samples have also been performed through SEM and an attempt has been made to correlate the macroscopic and microscopic results.
Characterization of the ESR response of alanine dosimeters to low-energy Cu-target X-tube photons
2017
Abstract This article describes Electron Spin Resonance (ESR) response measurements of Kodak BioMax alanine films exposed to low-energy X-rays from a Cu-target tube operating at 20 kV. Commercial alanine detectors were used to ensure maximum reproducibility of the results, while the choice of a film was due the low penetration of the soft X-rays. X-ray energy spectra and fluences were determined with an innovative digital semiconductor detector system. These data were used to quantify the irradiation of the alanine films in terms of absorbed dose to water. The alanine films were found to present a stable response, highly linear with dose. To our knowledge, these data have not been previousl…
Flow properties of low density/linear low density polyethylenes
1986
Rheological data have been collected both in shear and non-isothermal elongational flow on three different types of blends, made from one low density polyethylene sample and three linear low density polyethylene samples. In addition to the flow curves, data are presented on the extrudate-swell phenomenon, on the instability arising in capillary flow and on the tensile behavior in the molten state.
Influence of the molecular structure on the melt strength and extensibility of polyethylenes
1985
Melt strength (MS) and breaking stretching ratio (BSR) data relative to polyethylenes with different molecular structure (high density (HDPE), low density (LDPE), and linear low density (LLDPE)) are shown. HDPE and LLDPE samples show high breaking stretching ratio and low melt strength values. The LDPE samples exhibit very large melt strength values but low breaking stretching ratio values. For the last mentioned samples, differences are shown in the non-isothermal elongational behavior between samples polymerized with tubular and vessel technology. For all the samples, MS decreases with increasing melt index while BSR increases with melt index.
Blends of polyamide 6 and linear low density polyethylene functionalized with methacrylic acid derivatives
1997
Abstract Morphological, calorimetric, rheological, dielectric and mechanical behaviour of blends made with polyamide 6 (PA6) and linear low density polyethylene (PE) are presented. The PE was functionalized grafting ester and alcohol groups in a Brabender mixer with methacrylic acid derivatives. These groups induce “compatibilization” effects in the blends with respect to blends made with the unfunctionalized polyethylene. The difference effects on the behaviour of the blends of the various functional groups are shown. In particular, the interactions at the interface change depending on the chemical nature of the grafted groups. Ethyl and isobuthyl-methacrylate essentially cause dipolar int…
Photochemical stabilization of linear low-density polyethylene/clay nanocomposites: Towards durable nanocomposites
2008
International audience; This article reports a study of the chemical modifications of LLDPE/nanoblend nanocomposites exposed to UV light in conditions of artificially accelerated ageing and natural weathering. Analysis by infrared spectroscopy of the chemical modifications produced by photoageing shows that the presence of an organo-clay leads to the decrease of the oxidation induction time of the polymer (LLDPE), which results in lower durability of the nanocomposites. Protection against photooxidation was tested with different kinds of UV stabilizers and with a metal deactivator. It is shown that the metal deactivator is very efficient in stabilizing the nanocomposite since it totally can…
Elongational behavior of low density/linear low density polyethylenes
1988
Rheological data have been collected in isothermal elongational flow for three different types of blends, made from one low density polyethylene and three linear low density samples. In addition to the transient curves, elongation at break data are also reported. The influence of the composition and of the molecular weight of the linear low density polyethylene is discussed.