Search results for " mac"
showing 10 items of 3066 documents
Dynamic Modeling of Planar Multi-Link Flexible Manipulators
2021
A closed-form dynamic model of the planar multi-link flexible manipulator is presented. The assumed modes method is used with the Lagrangian formulation to obtain the dynamic equations of motion. Explicit equations of motion are derived for a three-link case assuming two modes of vibration for each link. The eigenvalue problem associated with the mass boundary conditions, which changes with the robot configuration and payload, is discussed. The time-domain simulation results and frequency-domain analysis of the dynamic model are presented to show the validity of the theoretical derivation.
A Self-Contained Electro-Hydraulic Cylinder with Passive Load-Holding Capability
2019
Self-contained electro-hydraulic cylinders have the potential to replace both conventional hydraulic systems and the electro-mechanical counterparts enhancing energy efficiency, plug-and-play installation, and reduced maintenance. Current commercial solutions of this technology are limited and typically tailor-made, whereas the research emphasis is primarily on cost efficiency and power applications below five [kW]. Therefore, there is the need of developing more flexible systems adaptable to multiple applications. This research paper offers a contribution in this regard. It presents an electro-hydraulic self-contained single-rod cylinder with passive load-holding capability, sealed tank, c…
Classification and Review of Pump-Controlled Differential Cylinder Drives
2019
Pump-controlled hydraulic cylinder drives may offer improved energy efficiency, compactness, and plug-and-play installation compared to conventional valve-controlled hydraulic systems and thus have the potential of replacing conventional hydraulic systems as well as electro-mechanical alternatives. Since the late 1980s, research into how to configure the hydraulic circuit of pump-controlled cylinder drives has been ongoing, especially in terms of compensating the uneven flow requirements required by a differential cylinder. Recently, research has also focused on other aspects such as replacing a vented oil tank with a small-volume pressurized accumulator including the consequences of this i…
A Comparison Study of a Novel Self-Contained Electro-Hydraulic Cylinder versus a Conventional Valve-Controlled Actuator—Part 2: Energy Efficiency
2019
This research paper presents the second part of a comparative analysis of a novel self-contained electro-hydraulic cylinder with passive load-holding capability against a state of the art, valve-controlled hydraulic system that is typically used in load-carrying applications. After addressing the control design and motion performance in the first part of the study, the comparison is now focused on the systems&rsquo
An Input Observer-Based Stiffness Estimation Approach for Flexible Robot Joints
2020
This letter addresses the stiffness estimation problem for flexible robot joints, driven by variable stiffness actuators in antagonistic setups. Due to the difficulties of achieving consistent production of these actuators and the time-varying nature of their internal flexible elements, which are subject to plastic deformation over time, it is currently a challenge to precisely determine the total flexibility torque applied to a robot's joint and the corresponding joint stiffness. Herein, by considering the flexibility torque acting on each motor as an unknown signal and building upon Unknown Input Observer theory, a solution for electrically-driven actuators is proposed, which consists of …
Using the Analytic Hierarchy Process (AHP) in Evaluating the Decision of Moving to a Manufacturing Process Based Upon Continuous 5 Axes CNC Machine-t…
2016
Abstract This paper represents the second part of the work described in the paper with the title “Decision-making tool for moving from 3-axes to 5-axes CNC machine-tool”. The problem of using either 3 axes CNC machine-tools or 5 axes CNC machine tools was presented in the first part, together with a fuzzy logic based decision support tool. This time, an AHP approach is used in order to evaluate the decision of moving to a manufacturing process based upon 5 axes machine tools. Three variants were taken into consideration and analysed. The consistency of the proposed approach was evaluated and a sensitivity analysis was also introduced.
Towards criteria for sustainable process selection: On the modelling of pure subtractive versus additive/subtractive integrated manufacturing approac…
2017
Additive Manufacturing (AM) processes can be counted among the disruptive technologies that are capable of transforming conventional manufacturing routes. The ability to create complex geometries, the reduction in material scraps during manufacturing, and the light-weighting due to the think-additive redesign of the components represent the main points of strength of AM. However, for some applications (such as the production of metal components for the automotive and aerospace industries), the surface finishing and dimensional/geometrical part tolerancing that can be achieved via AM processes might not be adequate to satisfy the imposed product specifications, and finish machining operation…
Simulación de Plataformas Robóticas de Movimiento para Aplicaciones de Realidad Virtual Mediante Filtros Digitales
2017
[ES] El uso de plataformas robóticas de movimiento en simuladores de vehículos y aplicaciones de Realidad Virtual es relativamente habitual. Sin embargo, el ajuste de los algoritmos que controlan su funcionamiento, denominados algoritmos de washout, no es sencillo y requiere de numerosas pruebas hasta obtener una apropiada fidelidad de movimiento. Disponer de herramientas que permitan simular plataformas de movimiento puede permitir simplificar esta tarea. Es por ello que este trabajo presenta un método para la caracterización y simulación de manipuladores robóticos mediante filtros digitales de segundo orden, sencillo de implementar y ajustar a partir de una caracterización previa. El simu…
Assessment of material models through simple machining tests
2008
The accuracy of the results obtained from FEM simulation of machining operations depends on the accuracy of input data. Among these, the flow stress data of the workpiece are extremely important together with the friction along the tool-chip interface. In this study, an identification procedure for the determination of material parameters that are used for the FEM simulation of machining processes is proposed. The procedure is based on the coupling of a numerical identification procedure and Arbitrarian Lagrangian Eulerian (ALE) Finite Element simulations of turning operations. An experimental campaign was developed in order to calibrate the model and to validate the procedure. The basic id…
A unified observer for robust sensorless control of DC–DC converters
2017
Abstract Due to the large variety of converters' configurations, many different sensorless controllers are available in the literature, each one suited for a particular converter. The need for different configurations, especially on the same power supply, make it clear the advantage of having a shared control algorithm. This paper presents a unified nonlinear robust current observer for buck, boost and buck–boost converters in synchronous and asynchronous configurations. The unified observer speeds up the design, tuning and the implementation, and requires a memory cheaper code, easier to certify. Simulation and experimental results are presented to validate the approach in different scenar…