Search results for " precision"
showing 10 items of 145 documents
Accuracy assessment and position correction for low-cost non-differential GPS as applied on an industrial peat bog
1999
A low-cost, non-differentially corrected hand-held GPS receiver was tested on an industrial peat production bog. A correction procedure (‘pseudo-differential correction’) was derived that corrected data points to the nearest position on a line defining the centre of each 15-m wide field. The result was a corrected log of track points for each field for all points lying along the field. It was found that the mean orthogonal distance from a field centreline was linearly correlated with mean uncorrected GPS data error (r 2 0.99) such that as GPS error increased so the accuracy obtained by correction decreased. For a signal with a mean uncorrected error of 30 m it was possible to reduce the err…
Residual errors in ASTER temperature and emissivity standard products AST08 and AST05
2011
Abstract Land surface temperature and emissivity are independent variables, and the thermal-infrared spectral radiance measured in remote sensing is dependent on both. Therefore the inverse Planck equation is under-determined, with two unknowns and a single measurement. Practical inversion algorithms designed to calculate temperature and emissivity from the measurements cannot do a perfect job of separation, and recovered temperature and emissivity may co-vary. For ASTER images, validation studies of recovered temperature and emissivity, regarded individually, have shown that they are within the precision and accuracy limits predicted in designing the ASTER TES algorithm used to calculate …
Gaia -ESO Survey: Analysis of pre-main sequence stellar spectra
2015
This paper describes the analysis of UVES and GIRAFFE spectra acquired by the Gaia-ESO Public Spectroscopic Survey in the fields of young clusters whose population includes pre-main sequence (PMS) stars. Both methods that have been extensively used in the past and new ones developed in the contest of the Gaia-ESO survey enterprise are available and used. The internal precision of these quantities is estimated by inter-comparing the results obtained by such different methods, while the accuracy is estimated by comparison with independent external data, like effective temperature and surface gravity derived from angular diameter measurements, on a sample of benchmarks stars. Specific strategi…
Comparison of in Situ Land Surface Temperatures Measured with Radiometers and Pyrgeometers: Consequences for Calibration and Validation of Thermal In…
2018
Land surface temperature (LST) is a key magnitude in many exchange processes between the surface and the atmosphere. LST measurement from satellites provides an efficient way to monitor its change across wide areas on Earth, an essential issue being LST validation using in situ measurements to assess its accuracy and precision. Presently, there are two widely used methodologies: temperature measurements made by wideband radiometers observing the land surface with a given viewing angle and a limited field of view, and measurements provided by total radiation pyrgeometers with a nearly hemispheric field of view. Although both measurements are correlated, they are not equivalent; thus, it is r…
3D reconstruction of hot metallic surfaces for industrial part characterization
2009
During industrial forging of big hot metallic shells, it is necessary to regularly measure the dimensions of the parts, especially the inner and outer diameters and the thickness of the walls, in order to decide when to stop the forging process. The inner and outer diameters of the shells range from 4 to 6 meters and to measure them a large ruler is placed horizontally at the end of the shell. Two blacksmiths standing on each side of the ruler at about ten meters from it visually reads the graduations on the ruler in order to determine the inner and outer diameters from which the thickness of the wall is determined. This operation is carried out several times during a forging process and it…
Objective Amplitude of Accommodation Computed from Optical Quality Metrics Applied to Wavefront Outcomes
2009
Purpose: We studied the accuracy and precision of 32 objective wavefront methods for finding the amplitude of accommodation obtained in 180 eyes. Methods: Ocular accommodation was stimulated with 0.5 D steps in target vergence spanning the full range of accommodation for each subject. Subjective monocular amplitude of accommodation was measured using two clinical methods, using negative lenses and with a custom Badal optometer. Results: Both subjective methods gave similar results. Results obtained from the Badal optometer where used to test the accuracy of the objective methods. All objective methods showed lower amplitude of accommodation that the subjective ones by an amount that varied …
230Th/U-dating of a late Holocene low uranium speleothem from Cuba
2010
We present 22 U-series ages for a stalagmite from north-western Cuba based on multi-collector inductively coupled plasma mass spectrometry (MC-ICPMS) and thermal ionisation mass spectrometry (TIMS). Our results reveal that the stalagmite continuously grew within the last ~1400a. Low uranium content of the sample and thus, extremely low 230Th concentrations limit the precision and accuracy of 230Th/U-dating by TIMS. Samples measured by MC-ICPMS show a high variability of 232Th content along the growth axis with some sections significantly affected by initial 230Th from a detrital phase. An a-priori bulk earth ratio for (238U/232Th) cannot be used to accurately account for this initial 230Th.…
Non-destructive automatic determination of aspect ratio and cross-sectional properties of fibres
2015
A novel method for computerised estimation of the aspect ratio distribution and various cross-sectional geometrical properties of fibres in short-fibre reinforced composites is proposed. The method, based on X-ray micro-computed tomography, is non-destructive and does not require user intervention. Based on results on specially fabricated model material, the accuracy and precision of the method seems adequate. The method is applied in analysing a manufacturing process of wood fibre reinforced thermoplastic composite. The results indicate a significant decrease of the aspect ratio of fibres during the processing steps. Finally, the feasibility of the method is assessed by estimating paramete…
Determination of knee joint cartilage thickness using three-dimensional magnetic resonance chondro-crassometry (3D MR-CCM)
1996
The objective of this article was to analyze the accuracy and precision with which the quantitative distribution of articular cartilage can be determined in the knee joint using MRI. A three-dimensional (3D) technique that accounts for the out-of-plane deviation of the interface normal in strongly curved joint surfaces (3D MR-CCM) has been developed for cartilage thickness measurements. Eight cadaveric knee-joint specimens and six volunteers were imaged using a fat-suppressed gradient-echo sequence at a resolution of 2 x 0.31 x 0.31 mm3. Cartilage volumes and topographical thickness maps were obtained and compared with those derived from anatomical sections by image analysis. The deviation …
The Randomized Shortened Dental Arch Study
2012
The scientific evidence concerning prosthodontic care for the shortened dental arch (SDA) is sparse. This randomized multicenter study aimed to compare two common treatment options: removable partial dental prostheses (RPDPs) for molar replacement vs. no replacement (SDA). One of the hypotheses was that the follow-up treatment differs between patients with RPDPs and patients with SDAs during the 5-year follow-up period. Two hundred and fifteen patients with complete molar loss in one jaw were included in the study. Molars were either replaced by RPDPs or not replaced according to the SDA concept. A mean number of 4.2 (RPDP) and 2.8 (SDA) treatments for biological or technical reasons occur…