Search results for " tecnologia."
showing 10 items of 1339 documents
A rapid and eco-friendly route to synthesize graphene-doped silica nanohybrids
2016
International audience; In the present study, the possibility to synthesize graphene oxide (GO)-based nanohybrids with pure and O2-doped silica nanoparticles by a rapid and easy hydrothermal process has been explored. The nanohybrids were prepared by varying the type of silica nanoparticles (average diameter 7 nm or 40 nm) and the silica/GO weight ratio. All the materials were fully characterized by spectroscopic and morphological techniques.The experimental results revealed that it is possible to tune the characteristics of the obtained nanohybrids, such as morphology and amount of ester/ether linkages upon varying the preparation parameters, together with the nanosilica's typology and the…
Phenomenological approach to compare the crystallization kinetics of isotactic polypropylene and polyamide-6 under pressure
2001
Reliable experimental data for semicrystalline polymers crystallized under pressure are supplied on the basis of a model experiment in which drastic solidification conditions are applied. The influence of the pressure and cooling rate on some properties, such as the density and microhardness, and on the product morphology, as investigated with wide-angle X-ray scattering (WAXS), is stressed. Results for isotactic polypropylene (iPP) samples display a lower density and a lower microhardness with increasing pressure over a wide range of cooling rates (from 0.01 to 20 °C/s). Polyamide-6 (PA6) samples exhibit the opposite behavior, with the density and microhardness increasing at higher pressur…
Taking advantage of the functional synergism between carbon nanotubes and graphene nanoplatelets to obtain polypropylene-based nanocomposites with en…
2020
Carbon Nanotubes (CNT) and Graphene Nanoplatelets (GNP) were incorporated in Polypropylene (PP) as single filler (CNT=1, 2 and 4 %wt. and GNP=2, 4, and 6 %wt.) and in hybrid form (CNT:GNP weight ratio 2:2, 2:4 and 4:2) using a prototype miniature Twin Screw Extruder (TSE) coupled with a double slit rheological die, in order to assess in-line the extent of nanofiller dispersion and to deliver PP-based nanocomposites with enhanced thermo-oxidative stability. The morphological, electrical and mechanical properties, as well as the resistance to thermal and photo degradation of the composites containing single nanofillers (PP/CNT and PP/GNP) were compared with those of hybrid PP based nanocompos…
Influence of resin viscosity and vacuum level on mechanical performance of sandwich structures manufactured by vacuum bagging
2010
The choice of process parameters is critical in optimizing the mechanical properties of sandwich structures produced using the vacuum bagging technique. The aim of this paper is to analyze how the viscosity of the resin/curing agent system and the vacuum level influence the morphology and the mechanical behavior of sandwich beams with composite faces (epoxy resin and glass fiber fabric named COMBI 900) and a PVC foam core. Four different sandwich structures were produced by varying the viscosity of the epoxy resin/curing agent at constant maximum vacuum pressure. Three further structures were manufactured by varying the strength of the vacuum with the resin viscosity maintained constant at …
Morphology and mechanical properties of extruded ribbons of LDPE/PA6 blends compatibilized with an ethylene-acrylic acid copolymer
2003
Two grades of low density polyethylene (LDPE) were blended with polyamide-6 (PA) in the 75/25 and 25/75 wt/wt ratios and shaped into ribbons with a Brabender single screw extruder. An ethylene-acrylic acid copolymer (EAA) was used in the 2 phr concentration as a compatibilizer precursor (CP). The morphology of the ribbons and its evolution during high temperature annealing were investigated by scanning electron microscopy (SEM). The results confirmed that EAA does actually behave as a reactive compatibilizer for the LDPE/PA blends. In fact, in the presence of EAA, the interfacial adhesion is improved, the dispersion of the minor phase particles is enhanced and their tendency toward fibrilla…
Phase separation of polymer blends in solution: A case study
2016
Abstract The phase behavior and phase separation features of the quaternary system poly- l -lactide (PLLA)/poly-rac-lactide (PLA)/dioxane/water were investigated. Experiments were performed with fixed total polymer concentration of 6 wt%, by varying the PLLA/PLA weight ratio. Blend weight compositions examined were 100/0, 80/20, 50/50, 20/80 and 0/100, at fixed dioxane/water weight ratio (87/13). Cloud point measurements reported that the demixing temperatures of blends are close to PLLA in the same mixed solvent, in line with the calculated spinodals. As regards to foam preparation, above the PLA cloud point, morphology is similar to pure PLLA foams; conversely, below PLA cloud point, the …
Accessibilità a Montalbano Elicona: un approccio multiscalare
2021
In any form of the built environment, in order to satisfy the requirement of accessibil- ity, there is a need to consider both material and intangible aspects through a multi- scalar approach. The architectural heritage does not sidestep this need. Any in-depth analysis or project needs to be designed whilst considering the relations and inter-connections between the building, public space and public services on an urban scale. This multi-scalar approach guided some studies carried out under the convention between the Department of Architecture of the University of Palermo and the Municipality of Montalbano Elicona, a small town of about 2,100 inhabitants in north-eastern Sicily. In this ca…
NANOTECNOLOGIE PER L'ARCHITETTURA TEMPORANEA
2009
È il tempo a sancire e a governare da sempre il rapporto fra architettura e storia. È il tempo che evidenzia la capacità dell’architettura di essere tramandata ai posteri, di essere eredità e testimonianza, di divenire simbolo caratterizzante un determinato periodo storico. Oggi il concetto di durata trova nuove variabili ed è soggetto a giudizio: la necessità di dare risposte immediate, una modernità sempre più indirizzata al rapido consumo, le esigenze continuamente mutevoli, la disponibilità di nuovi materiali, di componenti e di sistemi costruttivi hanno reso più attuale la realizzazione di manufatti provvisori e mobili. Il progetto si appropria così del tempo e ne controlla il suo stat…
METODO INNOVATIVO PER CREARE UN LAYER NANOSTRUTTURATO HONEYCOMB DI TITANIA, AUTOGENERATO SULLE SUPERFICI DI MATERIALI A BASE TITANIO, DESTINATI AL DO…
2011
NANOTECNOLOGIA, TITANIO, PROTESI ORTOPEDICHE, OSTEOSINTESI, NANOSTRUTTURA
Particle surface engineering effect on the mechanical, optical and photoluminescent properties of ZnO/vinyl-ester resin nanocomposites
2007
Zinc oxide (ZnO) nanoparticles functionalized with a bi-functional coupling agent methacryloxypropyl-trimethoxysilane (MPS) were used to fabricate a vinyl-ester resin polymeric nanocomposite, which shows an improved interfacial interaction between the particle and matrix. As a result, in comparison to the unmodified particle-filled nanocomposites, the functionalized particle-filled composites possessed higher resistance to thermal degradation, and demonstrated improved UV shielding and enhanced photoluminescent properties. The more uniform particle dispersion, passivation of the particle surface with MPS and increased oxygen vacancies were justified to contribute to the increased thermal st…