Search results for "ANNIHILATION"

Positronics of radiation-induced effects in chalcogenide glassy semiconductors

2015

Using As2S3 and AsS2 glasses as an example, the principal possibility of using positron annihilation spectroscopy methods for studying the evolution of the free volume of hollow nanoobjects in chalcogenide glassy semiconductors exposed to radiation is shown. The results obtained by measurements of the positron annihilation lifetime and Doppler broadening of the annihilation line in reverse chronological order are in full agreement with the optical spectroscopy data in the region of the fundamental absorption edge, being adequately described within coordination defect-formation and physical-aging models.

Positron annihilation probing of crystallization effects in TAS-235 glass affected by Ga additions

2014

Abstract Crystallization effects in Te20As30Se50 glass known also as TAS-235 affected by Ga additions to Ga2Te20As28Se50 and Ga5Te20As25Se50 compositions are probed with positron annihilation spectroscopy in the measuring modes exploring positron lifetimes and Doppler broadening of annihilation line. Occurring of cubic-phase Ga2Se3 droplets with character nanoscale sizes in partially-crystallized Ga2Te20As28Se50 alloy is shown to be associated with agglomeration of intrinsic free-volume voids, this process being enhanced over microcrystalline scale in Ga5Te20As25Se50 alloy. Crystallization changes in the void structure of TAS-235 glass are considered in terms of free-volume evolution under …

Investigation of the Absorption of Annihilation Quanta in Solid and Liquid Ga and BiSn Alloy

2001

Positron annihilation studies of recrystallization in the subsurface zone induced by friction in magnesium—effect of the inhomogeneity on measured po…

2013

The discussion of the positron annihilation studies of crystal structure defects, like vacancies, dislocations, grain boundaries and the defect depth profile, is presented. The role of the positron implantation depth and positron diffusion in such studies has been considered in detail. For description of the measured annihilation characteristics the proposed theoretical models take into account both effects. The annealing studies of defects created in pure magnesium by compression or dry sliding-wear were used for demonstration of the discussed thesis. The positron lifetime measurements were applied for monitoring open volume defects behavior. It was demonstrated that annealing at the tempe…

Positron Annihilation with Electrons of Admixture Atoms in Some Binary Nickel Alloys

2005

Weighted difference curves have been shortly presented as a proper tool allowing to analyze in another way two-detector Doppler spectra regarding positron annihilation with admixture electrons in some nickel alloys. The analysis of low and middle momentum parts of Doppler spectra for investigated alloys reflects the annihilation of positrons with admixture electrons. There is no distinct signal of annihilations with admixture electrons from the positron lifetime data for well-annealed samples.

Defects in Martensitic Stainless Steel 1.4031 (EN) Exposed to Friction as Seen by Positron Annihilation

2010

We present experimental results of measurements of the Doppler broadening of annihilation line and positron annihilation lifetimes in martensitic stainless steel 1.4031 (EN) samples exposed to the dry sliding under different loads. In particular, we tested the subsurface zone under the worn surfaces. As a main result, we obtained information about the defect profiles in this zone and the total extent of the damage region induced by the dry sliding.

Positron Microscopy Studies of Wear Tracks on a Copper Surface

2014

Positron microscopy was used for studies of defects induced by ball indentation or sliding on the surface of well-annealed copper samples. A focused positron beam of 24.5-keV energy was used to scan the deformed region of the indenter impression, and measurements of the annihilation line parameter were performed. In the case of ball indentation, the measured defect distribution correlates well with the von Mises stress distribution of the Hertz contact and the von Mises yield criterion. For the wear track produced by pin on disc dry sliding, an asymmetric defect distribution near the wear track is observed. It indicates the presence of a tangential force that additionally deforms the sample.

Recrystallization in subsurface zone seen by positron annihilation

2010

Abstract The paper presents studies of the defect distribution, detected by the positron annihilation method in the subsurface zone (SZ) of copper samples after dry sliding wear. It takes advantage of a new experimental technique based on scanning of the positron implantation profile. It allowed us to detect the defect profile in copper to the depth of 200 μm in a nondestructive way and study isochronal annealing behavior of this profile. We determined that annealing induces a recrystallization process which runs faster close to the surface than in deeper regions. After sliding, the complete recrystallization of the substructure takes place at temperature c.a. 600 °C. Some changes in the de…

Melting Process of the Sn-45 wt.% In and Sn-77 wt.% In Alloys as Viewed by Positron Annihilation

2006

The temperature dependences of the positron annihilation parameters F and R were determined for Sn–45 wt.% In and Sn–77 wt.% In alloys. The obtained results enabled to verify the vacancy and the quasicrystalline models of the melting process. It was found that for metals transforming into the liquid state from the structures different than the close packed structure, the melting transition are hardly explainable in terms of the vacancy model of melting. The strong trapping of positrons in metallic liquids is an indication of the presence of microvoids (vacancy clusters) or microcrystals containing defects more immense than vacancies. The share of these positron trapping centers in the volum…

Positron Annihilation Study of Defects Induced by Various Cutting Methods in Stainless Steel Grade 304

2011

We report in this article the comparison of the subsurface zones (SZs) in austenitic stainless steel 304 samples created by three cutting techniques, i.e., the laser cutting (LC), abrasive water jet (AWJ), and traditional milling cutting (MC). The crystal lattice defects distribution in this zone were investigated using the positron annihilation method. It was shown that the MC creates the great number mainly edge dislocations decorated by vacancies. Their concentration decreases with the increase of the depth from the cut surface. The total depth of the SZ is extended up to 150 μm from the cut surface. Similar dependency was observed for the AWJ machining but the total depth is much lower,…