Search results for "Acte"

Chironomid incorporation of methane-derived carbon in plankton- and macrophyte-dominated habitats in a large shallow lake

2018

1. While 13 C-depleted carbon derived from biogenic methane can substantially contribute to the benthic secondary production in deep stratified lakes, its role in shallow lakes is less clear. We investigated the dynamics of δ13 C and δ15 N in the larvae of Chironomus plumosus throughout an annual cycle in two ecologically distinct basins (open-water plankton-dominated and sheltered macrophyte- covered) of a large (270 km2 ), shallow, polymictic and eutrophic lake (Võrtsjärv, Estonia, North Europe). The larval stable isotopic compositions were linked to the presence of methane-oxidising bacteria (MOB) in larval guts and sediments. 2. Molecular detection of MOB revealed their presence in vari…

Limnology and Aquatic Microbial Ecology of Byers Peninsula: A Main Freshwater Biodiversity Hotspot in Maritime Antarctica

2019

Here we present a comprehensive review of the diversity revealed by research in limnology and microbial ecology conducted in Byers Peninsula (Livingston Island, South Shetland Islands, Antarctica) during the last two decades. The site constitutes one of the largest ice-free areas within the Antarctic Peninsula region. Since it has a high level of environmental protection, it is less human-impacted compared to other sites within the South Shetland archipelago. The main investigations in Byers Peninsula focused on the physical and chemical limnology of the lakes, ponds, rivers, and wetlands, as well as on the structure of their planktonic and benthic microbial communities, and on the function…

Editorial: Changing Plankton Communities: Causes, Effects and Consequences

2019

Eutrophication and browning influence Daphnia nutritional ecology

2019

Climate change and land-use practices can enhance lake eutrophication and browning, which influence phytoplankton composition by decreasing the availability of food high in nutritional quality (algae) and increasing the abundance of low-quality food (terrestrial detritus, bacteria) for herbivorous zooplankton. Nutritionally valuable algae for zooplankton are rich in essential biomolecules such as amino acids, polyunsaturated fatty acids (PUFAs), sterols, and phosphorus. We performed laboratory experiments and showed a stronger positive relationship between zooplankton (Daphnia) cumulative offspring number and availability of high-quality algae (Cryptophytes: Rhodomonas/Cryptomonas; and Chry…

Self-assembled multivalent (SAMul) ligand systems with enhanced stability in the presence of human serum

2019

Self-assembled cationic micelles are an attractive platform for binding biologically-relevant polyanions such as heparin. This has potential applications in coagulation control, where a synthetic heparin rescue agent could be a useful replacement for protamine, which is in current clinical use. However, micelles can have low stability in human serum and unacceptable toxicity profiles. This paper reports the optimi- sation of self-assembled multivalent (SAMul) arrays of amphiphilic ligands to bind heparin in competitive conditions. Specifically, modification of the hydrophobic unit kinetically stabilises the self-assembled nanostructures, preventing loss of binding ability in the presence of…

To incinerate or not? - Effects of incineration on the concentrations of heavy metals and leaching efficiency of post-precipitated sewage sludge (RAV…

2020

The major element and heavy metal concentrations of post-precipitated sewage sludge (PPS) and its ash residue (PPA) were determined using microwave digestion followed by inductively coupled plasma optical emission spectrometry (ICP-OES) and mass spectrometry (ICP-MS). To the best of our knowledge, this has not been previously done. In both PPS and PPA the heavy metal concentrations were clearly below the average concentrations than those encountered in sewage sludge in Europe. The leaching efficiency of the metal (Al/ Fe) used as a precipitation agent from post-precipitated sludge and its ash residue with phosphoric acid was also investigated with previously optimized leaching conditions. T…

BIOCLEANING

2017

Cleaning is one of the first and most important steps in conservative restora- tion intervention, as it removes the unwanted layers of dirt and deposit from the surface of an artefact. It must be done selectively, however, by adapting the cleaning operation to the different zones and removing successive layers of deposit without acting directly on the original materials of the surface. Generally, cleaning protocols are based on chemical or physical procedures with potential negative effects for restorers’ health and/or for the materials constituting the artworks. As an alternative, solvent gels, rigid gels and resin soaps can be used for selective cleaning. In recent decades, biological cle…

A comprehensive comparison between halophilic granular and flocculent sludge in withstanding short and long-term salinity fluctuations

2018

The effects of salinity fluctuations on the activity of autochthonous halophilic bacteria in aerobic granular sludge (AGS) and flocculent activated sludge (FAS) reactors were investigated. The response of nitrifiers and denitrifiers activity to drastic and moderate salinity shocks in the short-term (ST) and long-term (LT) was examined. The BOD5removal efficiency decreased only in the reactors subjected to the drastic LT salinity increase. Nevertheless, stable performances were achieved 18 days after the shock in the AGS-R1 (90%), whereas after 27 days in the FAS-R1 (82%). The loss in nitritation efficiency was higher in the FAS reactors and was proportional to the shock intensity. Nitritati…

Mechanical and metallurgical characterization of AA6082-T6 sheet-bulk joints produced through a linear friction welding based approach

2020

In the last decades, new flexible manufacturing processes have been developed to face the demands, by many industrial fields, for highly customized complex functional parts. The peculiar design of these components often overcomes conventional sheet metal and bulk metal forming processes capabilities. In order to face this issue, new hybrid techniques, capable of exploit key advantages of different processes, have to be developed. In this study, a method to obtain sheet-bulk joints, based on the Linear Friction Welding process, is proposed. The feasibility of the technique was investigated through an experimental campaign carried out with varying pressure and oscillation frequency using AA60…

Comparison of electropolishing behaviours of TSC, ALM and cast 316L stainless steel in H 3 PO 4 /H 2 SO 4

2017

Abstract In recent decades, new manufacturing processes have been developed such as Thermal Spray Coating (TSC) and Additive Layer Manufacturing (ALM), which reduce or avoid machining of parts with complex geometries. This study aims to develop an Electropolishing (EP) process for TSC and ALM 316L Stainless Steel (SS). EP is an anodic dissolution process currently used in industry to reduce surface roughness and obtain a bright and smooth finish. The EP mechanism was studied, in a mixture of H3PO4 and H2SO4, for TSC, ALM and “cast” SS in order to determine the best conditions (time, temperature, potential). Special attention was paid to surface characterization by combining several techniqu…