Search results for "Alum"
showing 10 items of 1303 documents
Dual role of interleukin-1alpha in delayed-type hypersensitivity and airway hyperresponsiveness.
2009
<i>Background:</i> Using a T helper (Th)1/Th2 disease model, we previously showed that genetically determined Th development depends on dendritic cell-derived interleukin (IL)-1α. In <i>Leishmania major</i> infections, Th1 immunity develops if IL-1α is present during T cell priming, whereas at later time points, IL-1α worsens disease outcome. In the present study, we determined the role of IL-1α in other Th2-mediated diseases. <i>Methods:</i> BALB/c mice were subjected to delayed-type hypersensitivity (DTH) or ovalbumin (OVA)/alum-induced allergic asthma in the presence or absence of IL-1α. <i>Results:</i> In DTH, mice treated with IL-1α durin…
Influence of initial treatments of aluminium on the morphological features of electrochemically formed alumina membranes
2003
Abstract The fabrication of alumina membranes by electrochemical oxidation of annealed aluminium was investigated. Porous layers were grown in 0.4 M H3PO4 at −1 and 5 °C at different anodising times. The morphology of the outer surface was found to be dependent on temperature and charge density, with both determining the extent of chemical dissolution of the anodic oxide. The inner-surface morphology was found to depend on the applied voltage only. The chemical dissolution rate of anodic oxide grown on annealed aluminium was found to be lower than that formed on unannealed aluminium under otherwise identical conditions. Such a difference in behaviour is explained in terms of a higher finish…
From C–S–H to C–A–S–H: Experimental study and thermodynamic modelling
2015
Abstract It has long been known that the stoichiometry of C–S–H varies with the calcium hydroxide concentration in solution. However, this issue is still far from understood. We revisit it in both experimental and modelling aspects. A careful analysis of the solubility confirms the existence of three different C–S–H phases, defined as Ca 4 H 4 Si 5 O 16 , Ca 2 H 2 Si 2 O 7 and Ca 6 (HSi 2 O 7 ) 2 (OH) 2 , respectively. The variation of the Ca/Si ratio of the three phases has been described by surface reactions: the increase of the Si content is accounted for by silicate bridging, the increase of calcium content and the surface charge are accounted for by reactions involving silanol groups v…
Behaviour of the high temperature corrosion of metals (TiAl3) coated with titanium aluminide
2010
During this study, intermetallic coatings TiAlx (x=1,2,3) were performed on titanium substrates: pure titanium and the commercial alloy, TA6V. The aim of this study was to elaborate aluminiure coatings on the surface and characterize the behaviour of these coated materials in oxidation at high temperature under air laboratory, under air enriched with water vapour and with sulfur. The coated materials were tested at three temperatures: 700°C, 800°C and 900°C. The coatings were realized at 1000°C by the pack-cementation process. The coatings realized are always adherent to the substrate. During oxidation the retrodiffusion of aluminium changes the nature of the phases and the organisation of …
On the Finite Element Simulation of Secondary Operations on Metallic Foams
2007
Metallic foams have been recently introduced also as industrial materials due to their well known advantages. In fact, their low mass in conjunction with the good thermal and mechanical properties push toward an extensive diffusion in manufacturing industry. In the study here addressed, a very accurate investigation concerning the latter two aspects has been carried out. In fact, a secondary manufacturing process, i.e. the foam bending, has been taken into account. Anyway, all the knowledge derived for sheet metal bending is not directly applicable to the foams. A finite element code has been utilized for modeling the foam behavior during the bending processes and an accurate material rheol…
Haemostatic agents on the shear bond strength of self-adhesive resin
2015
Background Dentin surface contaminated with haemostatic agents can interfere with the bonding of self-adhesive resin cement. Therefore the purpose of this study was to evaluate the effect of various haemostatic agents such as Aluminium chloride, Ferric sulphate and Tannic acid on the shear bond strength of self-adhesive resin luting agent. Material and Methods The buccal surfaces of extracted premolars were flattened to expose the dentine. The teeth were then randomly divided into four groups. In Group I Aluminium Chloride was applied on the flattened dentinal surface, in Group II Ferric Sulphate was applied to exposed dentin surface, in Group III tannic acid was applied on to the dentinal …
Mechanism of anionic polymerization of (meth)acrylates in the presence of aluminium alkyls, 1. 13C NMR studies of model compounds in toluene
1994
The bimetallic ate complex [(CH 3 ) 2 C=C(OEt)(O - AlR 3 )]Li + is regarded to be the model of the active centre of the polymerization of methyl methacrylate in the presence of aluminium alkyls. This complex is detectable by 13 C NMR up to 273 K. At ambient temperature irreversible decomposition takes place. Apart from the formation of the ate complex, excess aluminium chloride coordinates to the ester carbonyl groups of both the monomer and the polymer chain
On the mechanism of the interaction between oxygen and close-packed single-crystal aluminum surfaces
2003
Abstract Using periodic first principles simulations we investigate the interaction of oxygen molecules with both regular Al(111) and Al(001) surfaces as well as a stepped Al(111) substrate. The limitation of this approach is the use of thin metallic slabs with a limited range for their coverage by adsorbed oxygen. The advantage is the detailed modeling that is possible at an atomic level. On the regular Al(111) surface, we have been able to follow the oxidation process from the approach of O 2 molecules to the surface, through the chemisorption and absorption of O atoms, up to the formation of first Al 2 O 3 formula units. An energetically feasible mechanism for the formation of these Al 2…
Thermostimulated processes in statically and dynamically disordered luminescent solids
1993
Abstract Trap spectra depending on the concentration of defects in crystalline KBr-T1, LiF-Mg, Ti, A1 2 O 3 and glassy Na 2 O·SiO 2 are investigated. The nature of inhomogeneous broadening and continuous distribution of traps over activation energies at sufficiently high defect concentrations is considered. Impurity hopping controlled recombination of electronic excitations is observed. The presence of enlarged values of process activation energies and frequency factors is discussed in terms of the concept of dynamic disorder, taking into account the fluctuational changes in both the perfectpart and the structure of defects in the solid at high temperatures.
Defects in yttrium aluminium perovskite and garnet crystals: atomistic study
2000
Native and impurity point defects in both yttrium aluminium perovskite (YAP) and garnet (YAG) crystals are studied in the framework of the pair-potential approximation coupled with the shell model description of the lattice ions. The calculated formation energies for native defects suggest that the antisite disorder is preferred over the Frenkel and Schottky-like disorder in both YAP and YAG. The calculated values of the distortion caused by the antisite YAl x in the lattice turn out to be in an excellent agreement with the EXAFS measurements. In non-stoichiometric compounds, the calculated reaction energies indicate that excess Y2 O3 or Al2 O3 is most likely to be accommodated by the forma…