Search results for "Alum"
showing 10 items of 1303 documents
Analysis of Electrical Energy Demands in Friction Stir Welding of Aluminum Alloys
2017
Abstract Manufacturing processes, as used for discrete part manufacturing, are responsible for a substantial part of the environmental impact of products. Despite that, most of metalworking processes are still poorly documented in terms of environmental footprint. To be more specific, the scientific research has well covered conventional machining processes, concerning the other processes there is a lack of knowledge in terms of environmental load characterization instead. The present paper aims to contribute to fill this knowledge gap and an energetic analysis of Friction Stir welding (FSW) is presented. Following the CO2PE! methodological approach, power studies and a preliminary time stu…
Re-forming end-of-life components through single point incremental forming
2020
Abstract Applying Circular Economy strategies is mandatory to face material demand while minimizing the environmental impact. Manufacturing processes are to be thought as means to enable material/component reuse strategies. This paper presents the suitability of Single Point Incremental Forming (SPIF) to re-form End-of-life sheet metal components. Deep drawing followed by SPIF process on aluminium alloys were carried out to simulate reforming processes chain. The resulting thinning and strain distributions were experimentally analysed for different configurations. The research proves that the local action and enhanced formability nature of SPIF allow non-homogeneously thinned and reduced fo…
Energy demand reduction of aluminum alloys recycling through friction stir extrusion processes implementation
2019
Abstract Aluminum alloys are characterized by high-energy demands for primary production. Recycling is a well-documented strategy to lower the environmental impact of light alloys production. Despite that, conventional recycling processes are still energy-intensive with a low energy efficiency. Also, permanent material losses occur during remelting because of oxidation. Recently, several solid-state recycling approaches have been analyzed; in fact, by avoiding the remelting step both energy and material can be saved and, therefore, the embodied energy of secondary production can be substantially reduced. In this paper, the solid-state approach Friction Stir Extrusion (FSE) is analyzed for a…
Weld quality prediction in linear friction welding of AA6082-T6 through an integrated numerical tool
2016
Abstract A numerical and an experimental campaign were carried out with varying oscillation frequency and interface pressure. The local values of the main field variables at the contact interface between the specimens were predicted by a Lagrangian, implicit, thermo-mechanical FEM model and used as input of a dedicated Neural Network (NN). The NN, integrated in the FEM environment, was designed in order to calculate both a Boolean output, indicating the occurrence of welding, and a continuous output, indicating the quality of the obtained solid state weld. The analysis of the obtained results allowed three different levels of bonding quality, i.e., no weld, sound weld and excess of heat, to…
On the impact of recycling strategies on energy demand and CO2 emissions when manufacturing Al-based components
2016
Abstract The industrial world is facing the challenge of reducing emissions by means of energy- and resource-efficient manufacturing strategies. In some cases, the exerted emissions and the energy demands related to conventional manufacturing processes are not as intensive as those required to extract and produce the raw materials of which the workpieces are made. Therefore, the consciousness of the impact of material usage and the eco-informed choice of the end-of-life scenarios are both needed in view of sustainable development. Aim of this paper is to offer a contribution to a better understanding of the environmental impact of forming and machining processes, for the production of Al-ba…
Influence of friction stir processing conditions on the manufacturing of Al-Mg-Zn-Cu alloy/boron carbide surface composite
2018
Abstract Surface metal matrix composites were synthesized via friction stir processing (FSP) on the surface of aluminium alloy 7075 (AA 7075) sheets by incorporating B4C particles (B4CP). The influence of tool rotational speeds, powder particle sizes, and change in tool travel direction between FSP passes on particle distribution and resulting properties were studied in detail. Change in tool travel direction, decreased tool rotation speed and fine B4C particles enhanced B4CP distribution and wear properties thereof. Wear resistance of composites were doubled on account of the B4CP distribution and resultant several strengthening mechanisms.
Using infrared thermography in order to compare laser and hybrid (laser plus MIG) welding processes
2009
International audience; In order to deepen the understanding of the differences between laser and laser-arc hybrid welding, comparisons were undertaken using thermography. The experiments were carried out for a T assembly of aluminium alloy plates. Modelling, based on the finite element method approach, was realized using IR temperature measurements and seam geometry. For a value of the power supply, depicted as a surface source in the hybrid case, agreement was found between simulated and measured temperatures. The arc power supply efficiency value is similar to the usually used value.
The application of the random balance method in laser machining of metals
2008
International audience; Features peculiar to laser technology offer some advantages over more traditional processes, but, like all processes, it has its limitations. This article studies the limitations of laser machining of metals, and quantifies, through an experimental design method, the influence of operating parameters on productivity and on the quality of the machined surface. Three study materials were used: an aluminium alloy, stainless steel and a titanium alloy. An initial reading of the results indicates that productivity depends mainly on the frequency of the laser pulse and that the aluminium alloy behaves differently from the other two. The quality of the machined surface, jud…
Influence of processing parameters and initial temper on Friction Stir Extrusion of 2050 aluminum alloy
2017
Abstract Friction Stir Extrusion is an innovative production technology that enables direct wire production via consolidation and extrusion of metal chips or solid billets. During the process, a rotating die is plunged into a cylindrical chamber containing the material to be extruded. The stirring action of the tool produces plastic flow in the extrusion chamber, densifying and heating the charge so that finally, fully dense rods are extruded. Experiments have been carried out in order to investigate the influence of process parameters and initial temper of the base material on the process variables and on the extrudates’ mechanical properties.
Effect of active heating and cooling on microstructure and mechanical properties of friction stir–welded dissimilar aluminium alloy and titanium butt…
2019
A butt joint configuration of AA6061–pure Ti was welded using friction stir welding (FSW) with an assisted cooling and heating conditions, aiming to attain a flawless joint. Cooling-assisted friction stir welding (CFSW) was carried out with a different cooling medium such as CO2, compressed air and water at controlled flow rate. However, heating-assisted friction stir welding (HFSW) was performed with heating source of GTAW torch just before FSW tool at different current density. Prepared specimens were subjected to optical microscopy (OM), scanning electron microscopy (SEM) and electrodischarge spectroscopy (EDS) for microstructural characterizations. The tensile strength and microhardness…