Search results for "Analysi"
showing 10 items of 27203 documents
Mass calibration of the energy axis in ToF- E elastic recoil detection analysis
2016
We report on procedures that we have developed to mass-calibrate the energy axis of ToF-E histograms in elastic recoil detection analysis. The obtained calibration parameters allow one to transform the ToF-E histogram into a calibrated ToF-M histogram.
Description of intermodulation generation of nonlinear responses beyond the validity of the power series expansion
2021
Weakly nonlinear responses are commonly described by a power series expansion. However, intermodulation distortion products that cannot be described by a power series have been observed in a variety of physical systems. As the power series description is only applicable within its radius of convergence, we choose an alternative approach based on Fourier coefficients to describe intermodulation levels beyond the convergence of the power series. The description over a wide power range allows us to make a decision about models and to determine previously inaccessible model parameters. We apply the approach to data obtained from the characterization of the nonlinear dielectric susceptibility of…
THE GYROTRON STARTUP SCENARIO IN THE SINGLE MODE TIME DEPENDENT APPROACH
2019
The paper explains how to solve the Gyrotron equation system in the Single Mode Time Dependent Approach. In particular, we point out problems encountered when solving these well-known equations. The starting current estimation approach a using time model is suggested. The solution has been implemented in the Matlab code, which is attached to the article.
Determination of impurity distributions in ingots of solar grade silicon by neutron activation analysis
2017
AbstractIn a series of crystallization experiments, the directional solidification of silicon was investigated as a low cost path for the production of silicon wafers for solar cells. Instrumental neutron activation analysis was employed to measure the influence of different crystallization parameters on the distribution of 3d-metal impurities of the produced ingots. A theoretical model describing the involved diffusion and segregation processes during the solidification and cooling of the ingots could be verified by the experimental results. By successive etching of the samples after the irradiation, it could be shown that a layer of at least 60 μm of the samples has to be removed to get r…
Broadband Ultrahigh-Resolution Spectroscopy of Particle-Induced X Rays: Extending the Limits of Nondestructive Analysis
2016
Nondestructive analysis (NDA) based on x-ray emission is widely used, for example, in the semiconductor and concrete industries. Here, we demonstrate significant quantitative and qualitative improvements in broadband x-ray NDA by combining particle-induced emission with detection based on superconducting microcalorimeter arrays. We show that the technique offers great promise in the elemental analysis of thin-film and bulk samples, especially in the difficult cases where tens of different elements with nearly overlapping emission lines have to be identified down to trace concentrations. We demonstrate the efficiency and resolving capabilities by spectroscopy of several complex multielement …
Thermal oxidation of the intermetallic phases Al 8 Mo 3 and AlMo 3
2017
Abstract The thermal oxidation reactions of the intermetallic phases Al8Mo3 and AlMo3 were investigated and analyzed by ex-situ powder-x-ray diffraction (XRD), difference thermal analysis (DTA), thermogravimetry (TGA), and infrared spectroscopy (IR). The initial oxidation reactions in air were found to yield Al2O3 and AlMo3 in the case of Al8Mo3 (Tonset =725 °C), and MoO3 as well as Al8−xMo3 (Tonset =435 °C) for the pure intermetallic phase AlMo3, respectively. Thus, both intermetallic phases are coexisting in an equilibrium within a temperature range of 300 °C under oxidizing conditions. The formation of β-Al2(MoO4)3 followed the second oxidizing process of the respective minority componen…
Oxy-nitrides characterization with a new ERD-TOF system
2017
Abstract A new time-of-flight (TOF) camera was installed on Elastic Recoil Detection (ERD) measurement setup on the Tandem Accelerator at Universite de Montreal. The camera consists of two timing detectors, developed and built by the Jyvaskyla group, that use a thin carbon foil and microchannel plates (MCP) to produce the start and stop signals. The position of the first detector is fixed at 18 cm from the target, while the position of the second detector can be varied between 50 and 90 cm from the first detector. This allows to increase time resolution by increasing the distance between the time-of-flight detectors or to increase solid angle by decreasing the distance. Moving the detector …
The Effect of the Harmonic Content Generated by AC/DC Modular Multilevel Converters on HVDC Cable Systems
2019
With the increasing penetration of renewable and decentralized energy sources into the power grid, an extended use of DC voltages is expected on both distribution and transmission levels. Generation of DC voltages by means of voltage source converters is associated with a wide spectrum of harmonic distortions at converter terminals, both on the ac and on the dc sides. This can lead to partial discharges in power cables, which deteriorate insulation material thus weakening its performance and reducing cable life-time. In the previously published paper, the effect of harmonic distortion on appearance of partial discharges in cable insulation was evaluated. Here, the study related to the PD be…
Computer-aided analysis and design procedure for rotating induction machine magnetic circuits and windings
2018
The aim of this study is to present a new, accurate, and user-friendly software procedure for the analysis and rapid design of rotating induction machine windings, considering both the electric and the magnetic specifications of the machine itself. This procedure is a valid aid for quick first stage design without the necessity of using finite element method (FEM)-based design procedures. FEM can be used in a second design phase in order to refine the first stage results. The design procedure is hereafter outlined and some examples show its capability.
Hydrogen bonding interaction of N5H with water: A first principle calculations
2019
Abstract The cyclopentazol (N5H) and its anion counterpart (N5–) have been studied extensively over the years and detected in the gas phase as well as in solution recently. In the present investigation, an attempt has been made to understand the interaction with water molecule using first principle calculations. Nature of interactions have been studied using both energy decomposition analysis and atoms in molecule (AIM) theory calculations. Further, the strength of non-covalent interactions were analysed using IGMplots.