Search results for "Applied physics"
showing 10 items of 1226 documents
Overcoming synchronization issues in wireless technology Partial Discharge measurement
2016
In this paper, several aspects of the fundamentals of wireless Partial Discharge (PD) measurements are first discussed. Then, the relevance of the problem of voltage synchronization in PD wireless diagnosis is outlined. When portable instruments are used for PD detection, the main issue is the voltage measurement at the site where the PD detection is carried out. When such analysis is carried out over shielded cables, the AC (50/60 Hz) voltage reference signal is not easily detectable, while one of the basic parameters for PD diagnosis, the displacement of the inception voltage of the PD as compared to the reference voltage, is not available. Even if highperformance sensors are readily avai…
Interior permanent magnet synchronous motors: Impact of the variability of the parameters on their efficiency
2016
In the scientific literature, various authors presented different control strategies aimed to increase the efficiency of the interior permanent magnet synchronous motors. These strategies, starting from a well-known mathematical model of the dynamic behaviour of the motor, are able to reduce the power losses acting on the magnetizing component of the stator current. However, none of the proposed approaches takes into account that, varying the working conditions of the motor, also the values of the parameters, which have an impact on the power losses, can vary. In this paper, therefore, starting from an accurate measurement of the motor characteristics for various values of speed and load, w…
A cogging torque minimization procedure for IPMSMs based on different laminate geometry
2016
This paper presents a possible minimization procedure of the cogging torque generated by an IPMSM (Interior Permanent Magnet Synchronous Machine) with a progressive modification of a basic geometrical structure of rotor laminates. More in detail, an IPMSM model is analyzed by using a Finite Element Method (FEM) approach. Then, other IPMSM models, which are obtained by modifying the geometry of the IPMSM rotor laminates and by maintaining the same stator configuration, are proposed and discussed. From the obtained simulation results, the cogging torque components for each structure are determined by means of FEM and compared to each other. From this comparison, it can be stated that the cogg…
Piezoelectric Rainfall Energy Harvester Performance by an Advanced Arduino-Based Measuring System
2018
This paper presents the performances of rainfall energy harvesting through the use of a piezoelectric transducer and an Arduino-based measuring system. Different studies agree on the possibility of generating electricity from rainfall, but to date, a study on measuring the quantity of energy produced during rainfall is still missing. The present study begins with results obtained from laboratory researchers using piezoelectric transducers and oscilloscopes, finalized to measure the energy produced from a single raindrop, and concludes with an ad hoc Arduino-based measuring system, aimed to measure the actual amount of electrical energy produced by a piezoelectric transducer that is exposed …
Optimized design of high power density EMI filters for power electronic converters
2016
Nowadays, power density of power converters and related EMI filters is gaining more and more attention. This severely impacts on the design constraints in several application domains. A conventional design of the EMI filter does not guarantee the selection of components/configuration leading to the best power density. For this reason, an optimized design procedure of discrete EMI filters in terms of power density is proposed in this paper. It is based on a previously developed rule-based design procedure, introducing here additional features to obtain a more effective optimization of EMI filter's power density. The proposed approach has been validated in terms of EMI filter's performance an…
Greening island: Renewable energies mix to satisfy electrical needs of Pantelleria in Mediterranean sea
2016
In this article the authors analyze the renewable mix in order to satisfy the energy needs of a real island in the Mediterranean sea, Pantelleria, which represents an optimal starting point to increase the production of electrical energy from renewable sources in minor islands. In this text are exposed different alternative sources, such as solar, wind and wave energy. Moreover, it is exposed a project of an innovative conversion device proposed by Department of Energy of University of Palermo, compared to a different one proposed by Politecnico di Torino. The procedures applied in the present article, as well as the main equations used, are the result of previous applications made in diffe…
A tunnel magnetoresistive effect wattmeters-based wireless sensors network
2017
Abstract In the present work a wireless sensors network (WSN) for smart energy metering is presented using the ZigBee protocol as the communication link. Each network node process the electrical power by means of a Wheatstone bridge sensor based on the tunnel magnetoresistive (TMR) effect working as analogue multiplier. The electrical power is acquired and processed by a digital signal processor that extracts various parameters of interest like current and voltage load, active power and power factor by means of Fourier analysis. All the obtained electrical parameters at each node are served and shown in a web page that can be easily accessed by authorized users.
New statistical post processing approach for precise fault and defect localization in TRI database acquired on complex VLSI
2013
International audience; Timing issue, missing or extra state transitions or unusual consumption can be detected and localized by Time Resolved Imaging (TRI) database analysis. Although, long test pattern can challenge this process. The number of photons to process rapidly increases and the acquisition time to have a good signal over noise ratio (SNR) can be prohibitive. As a result, the tracking of the defect emission signature inside a huge database can be quite complicated. In this paper, a method based on data mining techniques is suggested to help the TRI end user to have a good idea about where to start a deeper analysis of the integrated circuit, even with such complex databases.
Frequency mapping in dynamic light emission with wavelet transform
2013
International audience; Dynamic photon emission microscopy is an e cient tool to analyse today's integrated circuit. Nevertheless, the reduction of transistor's dimensions leads to more complex acquisitions where many spots can be seen. A frequency characterization of the whole acquired area can help to have a better understanding of it. With that purpose in mind, a new methodology to draw frequency mapping of dynamic light emission acquisition is reported. It is fully automated and based on wavelet transform and autocorrelation function. Regarding the possible use in an industrial context, the suggested method can help to localize abnormal emission activity and it gives some perspectives o…
Finite-element performance comparison of IPMSMs with unsymmetrical double-layer windings
2017
This paper presents a comparison of the performances between IPMSMs (Interior Permanent Magnet Synchronous Machine) with a symmetrical and with two different types of unsymmetrical windings. The aim is to demonstrate that the adoption of slightly unsymmetrical windings does not significantly affect the performances of the machines, both in terms of cogging torque and torque/load angle characteristics, providing also the advantage of a higher possibility of choice in terms of slot number/poles ratio. More in particular, an IPMSM model (named IPMSM-1) derived from a commercial geometry equipped with a symmetrical winding is analyzed by using a Finite Element Method (FEM) approach. The simulat…