Search results for "Ball mill"

Influence of the high energy ball milling on structure and reactivity of the Ni+Al powder mixture

2013

Abstract Investigation of the micro- and atomic structures for the planetary ball-milled Ni + Al mixtures has revealed existence of intermediate nano-crystalline and amorphous phases, which are not detectable by XRD analysis, but can be observed by means of HRTEM. Annealing of the milled mixtures at moderate temperature, 205–280 °C, transforms the nano-phases into crystal state and makes them XRD-detectable. These nano-scale structures may serve as nucleus for the intermetallic phases produced via reaction between Ni and Al and, therefore, decrease the activation energy of this reaction and diminish the temperature of the reaction initiation. Apparently, the active nano-phases are formed du…

Influence of mechanical activation on the physical stability of salbutamol sulphate.

2003

Abstract In order to obtain the optimal particle size distribution for pharmaceutical powders in dry powder inhalers the particles have to be micronised. In most cases the process of micronisation is connected with a high input of energy which induces disorder and defects on the surface of the drug particles and as a result changes in the crystallinity. Consequently, changes in the physical stability of the powders may occur. To investigate changes on the physical stability of the powder, different analytical methods are used in the present investigation: laser diffraction, Differential Scanning Calorimetry (DSC), isothermal microcalorimetry and DVS-method. Air-jet-milling is one of the mos…

Enhancement of self-sustaining reaction Cu3Si phase formation starting from mechanically activated powders

2000

Mechanical high-energy ball milling of an 3Cu Si elemental powders mixture was used to activate a self-sustaining combustion reaction or so-called self-sustaining high-temperature synthesis (SHS) to form the copper silicide phase, a reaction for which the thermodynamic criterion proposed by Munir for self-propagation reaction is not favorable. A complete characterization of the end-products was performed with X-ray diffraction analysis and scanning electron microscopy. Thermal and structural information describing the combustion front initiated by heating up a sample to 180°C in a Cu:Si system is communicated. This paper clearly shows that the mechanically activated self-sustaining high-tem…

Effects of ball-milling on the hydrogen sorption properties of LaNi5

2009

Abstract Pressure–composition isotherms of LaNi 5 alloys were studied as function of ball-milling time. Results indicate that ball-milling convert a part of the LaNi 5 to a non-absorbing state—a state which does not absorb hydrogen under conditions where un-milled LaNi 5 powders absorb and transform to LaNi 5 H 6 , in addition to particle size reduction and creation of defects. The non-absorbing fraction in the milled sample is found to grow with increase in the ball-milling time. The resistance to the hydride formation of the long-time ball-milled LaNi 5 samples is found to continue even after a 1-h high vacuum annealing at around 1000 K. This indicates that the hydrogen-absorption-resist-…

Synthesis of nanocrystalline NbAl3 by mechanical and field activation

2001

Abstract The mechanically-activated, field-activated, and pressure-assisted synthesis (MAFAPAS) process, which combines the simultaneous synthesis and densification of nanophase materials, was utilized to produce nanocrystalline NbAl3 material from Nb+3Al mechanically activated powders. Nb+3Al elemental powders were co-milled for a short time in a specially designed planetary ball mill to obtain nanoscale distributed reactants but to avoid the formation of any product phases. These were then subjected to high AC currents (1500–1650 A) and uniaxial pressures (56–84 MPa). Under these conditions, a reaction is initiated by field activation and completed within a short period of time (3–6 min).…

Nanoconfined mixed Li and Mg borohydrides as materials for solid state hydrogen storage

2012

Abstract Several mixtures of LiBH4 and Mg(BH4)2 borohydrides in different stoichiometric ratios (1:0, 2:1, 1:1, 1:2, 0:1), prepared by high energy ball milling, have been investigated with X-ray powder diffraction and thermal programmed desorption (TPD) volumetric analysis to test the dehydrogenation kinetics in correlation with the physical mixture composition. Afterwards mixed and unmixed borohydrides were dispersed on high specific surface area ball milled graphite by means of the solvent infiltration technique. BET and statistical thickness methods were used to characterize the support surface properties, and SEM micrographs gave a better understanding of the preparation techniques. It …

Synthesis of niobium aluminides using mechanically activated self-propagating high-temperature synthesis and mechanically activated annealing process

1999

The mechanically activated self-propagating high-temperature synthesis (MASHS) technique and the mechanically activated annealing process (M2AP) were used to produce NbAl3 intermetallic compound. The MASHS process results from the combination of two steps: first, a mechanical activation of the Nb 3Al powders mixture; second, a self-propagating high-temperature synthesis (SHS). The M2AP process also results from the combination of two steps: the first is the same; the second consists of the annealing of as-milled powders. Based on X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and X-ray energy dispersive spectroscopy (EDXS), the as-milled powders, MASHS, and M2AP end-pr…

Dense Mosi2 produced by reactive flash sintering: Control of Mo/Si agglomerates prepared by high-energy ball milling

2011

The objective of this work is to determine the influence of the agglomeration state of the MA mixture on the microstructure and the chemical composition of SPS end-products. In order to produce MoSi2 with a microstructure and a density perfectly controlled via reactive sintering implying an SHS reaction, the characteristics of Mo/Si mechanically activated (MA) powder mixtures were investigated. Indeed, the MA powders have been characterized in terms of their surface specific area, size, phase composition and microstructure. The high-energy milling allows the formation of agglomerates (0.8 to 800 μm) composed of nanometric crystallites of molybdenum and silicon, as a consequence of a continu…

Dilatometric Characterization of Micrograined Metallic Powders

1995

Synergistic effects of multiwalled carbon nanotubes and Al on the electrochemical hydrogen storage properties of Mg2Ni-type alloy prepared by mechani…

2012

Abstract Mg 2− x Al x Ni ( x  = 0, 0.25) electrode alloys with and without multiwalled carbon nanotubes (MWCNTs) have been prepared by mechanical alloying (MA) under argon atmosphere at room temperature using a planetary high-energy ball mill. The microstructures of synthesized alloys are characterized by XRD, SEM and TEM. XRD analysis results indicate that Al substitution results in the formation of AlNi-type solid solution that can interstitially dissolve hydrogen atoms. In contrast, the addition of MWCNTs hardly affects the XRD patterns. SEM observations show that after co-milling with 5 wt. % MWCNTs, the particle sizes of both Mg 2 Ni and Mg 1.75 Al 0.25 Ni milled alloys are decreased e…