Search results for "Biocomposite"

Analysis of the Parameters Affecting the Stiffness of Short Sisal Fiber Biocomposites Manufactured by Compression-Molding

2021

The use of natural fiber-based composites is on the rise in many industries. Thanks to their eco-sustainability, these innovative materials make it possible to adapt the production of components, systems and machines to the increasingly stringent regulations on environmental protection, while at the same time reducing production costs, weight and operating costs. Optimizing the mechanical properties of biocomposites is an important goal of applied research. In this work, using a new numerical approach, the effects of the volume fraction, average length, distribution of orientation and curvature of fibers on the Young’s modulus of a biocomposite reinforced with short natural fibers were stud…

Opuntia Ficus Indica based green composites for NPK fertilizer controlled release produced by compression molding and fused deposition modeling

2022

Excessive fertilization causes ecological problems due to leaching issues. To solve this problem and promote agriculture sustainability an innovative green composite for controlled release fertilizers was produced by adding NPK fertilizer flour to a biodegradable polymer with or without Opuntia Ficus Indica (OFI) particles. Six for- mulations were produced and employed for the fabrication of devices both for compression molding and fused deposition modeling (FDM). Both fillers displayed a good dispersion in the composites, excellent adhesion with the polymeric matrix and effectively acted as reinforcement. The decrease of NPK release rate (up to 30 days) was achieved using whole composites …

Mechanical response of PLA-based biocomposites under creep conditions

2017

Over the last decades, polymer composites containing natural fibers are receiving growing attention both from academia and the industry, as possible alternatives of composites containing synthetic fibers [1]. Moreover, in order to reduce the environmental impacts related to the use of oil-derived polymer matrices, biodegradable ones obtained from renewable sources such as poly(lactic acid) (PLA) have been considered [2]. Several papers are available regarding the mechanical behavior of natural fibers reinforced PLA composites, but only few deal with their creep behavior [3]. In the present work, the tensile creep behaviour of PLA based composites, containing flax and jute plain weave woven …

Green composites for fertilizer controlled release produced by compression molding and FDM

2023

Excessive fertilization causes ecological problems due to leaching issues. To solve this problem and promote agriculture sustainability an innovative green composite for controlled release fertilizers was produced by adding NPK fertilizer flour to a biodegradable polymer with or without Opuntia Ficus Indica (OFI) particles. Six formulations were produced and employed for the fabrication of devices both for compression molding (CM) and fused deposition modeling (FDM). Both fillers displayed a good dispersion in the composites, excellent adhesion with the polymeric matrix and effectively acted as reinforcement. The decrease of NPK release rate (up to 30 days) was achieved using whole composit…

Physical and antibacterial properties of PLA electrospun mats loaded with carvacrol and nisin

2022

Functional, biopolymeric electrospun structures for the controlled release of antimicrobial agents are gaining in-creasing interest in food packaging applications. In this study, the physical and antibacterial performances of ternary systems composed of polylactic acid (PLA) electrospun mats loaded with 20 wt% of different relative amounts of carvacrol (CRV) and a commercial nisin formulation (Nis) were assessed. Scanning electron micrographs displayed micro-scaled fibers with different diameter size distributions depending on the relative concentrations of the additives. The PLA/CRV/Nis membranes??? wettability was affected by the relative amount of CRV and Nis loaded, switching from hydro…

The Use of Waste Hazelnut Shells as a Reinforcement in the Development of Green Biocomposites.

2022

Biodegradable Mater-Bi (MB) composites reinforced with hazelnut shell (HS) powder were prepared in a co-rotating twin-screw extruder followed by compression molding and injection molding. The effects of reinforcement on the morphology, static and dynamic mechanical properties, and thermal and rheological properties of MB/HS biocomposites were studied. Rheological tests showed that the incorporation of HS significantly increased the viscosity of composites with non-Newtonian behavior at low frequencies. On the other hand, a scanning electron microscope (SEM) examination revealed poor interfacial adhesion between the matrix and the filler. The thermal property results indicated that HS could …

Polymer-based 'green' composites

2009

Water absorption and hydrothermal performance of PHBV/sisal biocomposites

2014

[EN] The performance of biocomposites of poly(hydroxybutyrate-co-valerate) (PHBV) and sisal fibre subjected to hydrothermal tests at different temperatures above the glass transition of PHBV (TH ¿ 26, 36 and 46 C) was evaluated in this study. The influences of both the fibre content and presence of coupling agent were focused. The water absorption capability and water diffusion rate were considered for a statistical factorial analysis. Afterwards, the physico-chemical properties of water-saturated biocomposites were assessed by Fourier-Transform Infrared Analysis, Size Exclusion Chromatography, Differential Scanning Calorimetry and Scanning Electron Microscopy. It was found that the water d…

Effective elastic properties of biocomposites using 3D computational homogenization and X-ray microcomputed tomography

2021

A 3D computational homogenization method based on X-ray microcomputed tomography (μCT) was proposed and implemented to investigate how the fiber weight fraction, orthotropy and orientation distribution affect the effective elastic properties of regenerated cellulose fiber-polylactic acid (PLA) biocomposites. Three-dimensional microstructures reconstructed by means of the X-ray μCT were used as the representative volume elements (RVEs) and incorporated into the finite element solver within the computational homogenization framework. The present method used Euclidean bipartite matching technique so as to eliminate the generation of artificial periodic boundaries and use the in-situ solution d…

Structure and performance properties of environmentally-friendly biocomposites based on poly(ɛ-caprolactone) modified with copper slag and shale dril…

2018

The potential application of two types of industrial wastes, drill cuttings (DC) and copper slag (CS), as silica-rich modifiers of poly(ɛ-caprolactone) (PCL) was investigated. Chemical structure and physical properties of DC and CS fillers were characterized using X-ray diffractometer, X-ray fluorescence spectroscopy, particle size and density measurements. PCL/DC and PCL/CS composites with a variable content of filler (5 to 50 parts by weight) were prepared by melt compounding in an internal mixer. It was observed that lower particle size of DC filler enhanced processing of biocomposites comparing to CS filler. Smaller particles of DC filler and thus the higher specific surface area, enabl…