Search results for "Biodegradable polymers"
showing 10 items of 26 documents
The Use of Waste Hazelnut Shells as a Reinforcement in the Development of Green Biocomposites.
2022
Biodegradable Mater-Bi (MB) composites reinforced with hazelnut shell (HS) powder were prepared in a co-rotating twin-screw extruder followed by compression molding and injection molding. The effects of reinforcement on the morphology, static and dynamic mechanical properties, and thermal and rheological properties of MB/HS biocomposites were studied. Rheological tests showed that the incorporation of HS significantly increased the viscosity of composites with non-Newtonian behavior at low frequencies. On the other hand, a scanning electron microscope (SEM) examination revealed poor interfacial adhesion between the matrix and the filler. The thermal property results indicated that HS could …
Polymer-based 'green' composites
2009
Biodegradable polymer-wood flour composites: main properties and biodegradability
2009
During the last years, a considerably increasing rate of attention has arisen on biodegradable polymers. In the meanwhile, the use of wood-plastic composites (WPC) has grown in importance, especially in the United States. The combination of biodegradable polymers and wood-based fillers allows obtaining the typical advantages achievable with the use of WPCs, with the further advantage of the biodegradability and compostability of the matrix (and not only of the filler). In this work, the characterization and the biodegradability assessment of Mater-Bi®-wood flour composites have been carried out.
LEMONGRASS PLANT LEAF AND CULM AS POTENTIAL SOURCES OF REINFORCEMENT FOR BIO-COMPOSITES
2022
A possible source of natural reinforcement for bio-composites can be represented by lemongrass plant (Cymbopogon flexuosus), a clumped and perennial grass which belongs to the Poaceae family. This plant is extensively used for several applications such as pharmacology, food preservation and cosmetics but, to the best of our knowledge, few papers were published on its use as source for reinforcement of composites and no one article was focused on the comparison between lemongrass leaves and culms as potential source of natural reinforcement. To this aim, a preliminary investigation on leaf and culm fibers was carried out to compare their physical and chemical features as well as their tensil…
USE OF BIODEGRADABLE POLYMERS FOR FOAM EXTRUSION
2013
Toward the Decarbonization of Plastic: Monopolymer Blend of Virgin and Recycled Bio-Based, Biodegradable Polymer.
2022
Decarbonization of plastics is based on two main pillars: bio-based polymers and recycling. Mechanical recycling of biodegradable polymers could improve the social, economic and environmental impact of the use of these materials. In this regard, the aim of this study was to investigate whether concentrations of the same recycled biopolymer could significantly affect the rheological and mechanical properties of biodegradable monopolymer blends. Monopolymer blends are blends made of the same polymers, virgin and recycled. A sample of commercially available biodegradable blend was reprocessed in a single-screw extruder until two extrusion cycles were completed. These samples were exposed to gr…
Photo-Oxidative and Soil Burial Degradation of Irrigation Tubes Based on Biodegradable Polymer Blends
2019
: Irrigation tubes based on biodegradable polymers were prepared via an extrusion-drawing process by Irritec and compared to conventional pipes made of high-density polyethylene (HDPE). A commercial polylactide/poly (butyleneadipate-co-butyleneterephthalate) (PLA/PBAT) blend (Bio-Flex®
Polymeric scaffolds based on blends of poly-l-lactic acid (PLLA) with poly-d-l- lactic acid (PLA) prepared via thermally induced phase separation (TI…
2012
Porous scaffolds based on blends of high crystalline Poly-L-lactic acid (PLLA) with low crystalline poly-D-L-lactic acid (PLA) were prepared via Ther- mally Induced Phase Separation (TIPS), with the aim of exploring the possibility to control the degradation behaviour of the PLA-based scaffold, simultaneously pre- serving the morphological characteristics required for tissue engineering applica- tions. Porous foams with different PLLA/PLA weight ratios (from 95/5 to 60/40) were produced and characterised in terms of pore size, porosity, and thermal properties. The scaffolds present an open porosity, with average pore sizes ranging from 30 to 70 lm. Results showed that, when dealing with a P…