Search results for "Biot"
showing 10 items of 8384 documents
Vibration Control of a High-Speed Precision Servo Numerically Controlled Punching Press: Multidomain Simulation and Experiments
2017
A three-degree-of-freedom mathematical vibration model of a high-speed punching press was developed in order to explore the vibration modes of the punching press. A multidomain model of the punching press was established to predict the kinematic state during different conditions, as well as the effects of load fluctuation on the motor speed. Experimental measurements of the acceleration of the punching press were carried out. The results comparison reveals that the multidomain model is consistent with the vibration model and the experimental measurements. Modal analysis and structure modification of the punching press were conducted. The foundation at the base of the punching press was impr…
Neural modelling of friction material cold performance
2008
The complex and highly non-linear phenomena involved during braking are primarily caused by friction materials’ characteristics. The final friction materials' characteristics are determined by their compositions, manufacturing, and the brake's operating conditions. Analytical models of friction materials' behaviour are difficult, even impossible, to obtain for the case of different brakes' operating conditions. That is why, in this paper, all relevant influences on the friction materials' cold performance have been integrated by means of artificial neural networks. The influences of 26 input parameters, defined by the friction materials' composition (18 ingredients), manufacturing (five pa…
Springback of thick sheet AHSS subject to bending under tension
2012
Lien vers la version éditeur : http://www.sciencedirect.com/science/article/pii/S0020740312000677 The springback behavior of four advanced high-strength sheet steels (Dual-Phase, TRIP, ferrite-bainite) with thicknesses ranging from 1.2 to 4 mm was investigated by means of the bending-under-tension (BUT) test. The applicability of several guidelines from the literature was investigated experimentally and numerically. The monotonic decrease of springback as back force increased was confirmed for this category of sheet steels, and a general trend for the non-linear influence of the tool radius was observed. The influence of numerical factors on the predicted values of springback was investigat…
Quasi-Static Displacement Self-Sensing Measurement for a 2-DOF Piezoelectric Cantilevered Actuator
2017
This paper proposes a self-sensing measurement technique to perform the precise estimation of the displacements along two axes in a two-degrees-of-freedom (2-DOF) piezoelectric actuator. For that, a new electrical circuit scheme that permits charge amplification is first proposed to match the different electrodes combination of the 2-DOF actuator. Then, a new bivariable observer that precisely estimates the displacements is calculated and implemented experimentally in a cascade with the electrical circuit to complete the self-sensing. The experimental tests and results verification with external sensors revealed that the measured displacements given by the developed self-sensing measurement…
Robust control for high performance induction motor drives based on partial state-feedback linearization
2019
This paper deals with a robust input-output feedback linearization control technique for induction motors. Indeed, classic feedback linearization presents two main disadvantages: 1) the accuracy of the dynamic model; and 2) the corresponding correct knowledge of the model parameters. To address this issue, the linear controller has been substituted with a suitably controller designed to be robust to the variations of the main parameters of the induction motor, like stator and rotor resistances, and the three-phase magnetizing inductance. The proposed controller has been tested both in numerical simulation and experimentally on a suitably designed test setup. Moreover, it has been compared w…
Current fault signatures of Voltage Source Inverters in different reference frames
2016
This paper considers different current patterns used to identify the correct fault signatures in Voltage Source Inverters (VSI). At the beginning, the Authors consider the currents patterns from which a simple or a double fault can be encompassed both in the case of controllable device only or with its free wheeling companion diode. After the discussion of diagnosis algorithm suitable for electrical drives and principally based on a persistent near zero current condition current in the natural phase reference frame, the stationary reference frame is then considered as a tool to identify both the faulted phase as the device or various combination of faulted devices. On the contrary, the Auth…
Enhancing tracking performance in a smartphone-based navigation system for visually impaired people
2016
In this paper we show how to enhance the tracking performance of Arianna, a low-cost augmented reality system designed to meet the needs of people with problems of orientation, people with sight impairment and blind people. For augmented reality system we mean the design of: i) a set of paths and tags to be deployed in the environment, realized in various ways depending on the context (decorative elements easily identifiable, colorful stripes, QR code, RFID, etc.); ii) an instrument of mediation between the reality and the user (typically a smartphone) to access the information disseminated in the environment by means of a camera and provide a vibration feedback signal to the users for foll…
Effect of the mutual position between weld seam and reinforcement on the residual stress distribution in Friction Stir Welding of AA6082 skin and str…
2016
Abstract In the paper, a numerical and experimental study was carried out to highlight the effect of the distance d between the weld seam and the reinforcement on the residual stress distribution in Friction Stir Welded AA6082-T6 structures. An L-shaped profile was welded to a sheet metal with varying tool rotation and distance d from the weld seam. The Cut Compliance method was used to determine the resulting longitudinal residual stress. A dedicated FE model for FSW was set up, validated and utilized to predict the longitudinal residual stress in the assembled part. The analysis allowed the identification of a few design guidelines in order to reduce the detrimental effects of the residua…
Physical Load Among Construction Workers and Analysis with Objective Ergonomics Research Method
2016
There is growing number of work related musculoskeletal disorders among workers in construction industry. Employees in construction professions admit physical load and discomfort in various body parts after the work. Accordingly to Eurostat statistical data 60 % of total work related diseases are attributed to musculoskeletal disorders in Latvia. The aim of this study was to determine physical load of construction auxiliary workers and bricklayers using objective ergonomics research method HR monitoring and subjective ergonomic risk assessment methods. The research involved full time 8 auxiliary construction workers and 7 bricklayers. Analysis of the heart rate monitoring data proved that o…
A review of diagnostics and prognostics of low-speed machinery towards wind turbine farm-level health management
2016
Abstract Large wind farms are gaining prominence due to increasing dependence on renewable energy. In order to operate these wind farms reliably and efficiently, advanced maintenance strategies such as condition based maintenance are necessary. However, wind turbines pose unique challenges in terms of irregular load patterns, intermittent operation and harsh weather conditions, which have deterring effects on life of rotating machinery. This paper reviews the state-of-the-art in the area of diagnostics and prognostics pertaining to two critical failure prone components of wind turbines, namely, low-speed bearings and planetary gearboxes. The survey evaluates those methods that are applicabl…