Search results for "Building"
showing 10 items of 1985 documents
Flexural behaviour of glulam timber beams reinforced with FRP cords
2015
Abstract Glued laminated timber (glulam) is widely used as a construction material to make up lightweight and large span structures. The basic principle of this material consists in bonding together a number of layers of dimensioned timber with structural adhesives, in order to increase strength and stiffness of the member, and allowing to make up sustainable structures with great visual impact. Recent applications showed the effectiveness of fibre-reinforced polymer (FRP) composites in enhancing the structural performances of glulam beams, with particular reference on their flexural and shear strength. In fact FRP reinforcements could be used to strengthen existing structures or to reduce …
Influence of axial force and corrosion on failure of prestressed concrete structures considering M-V interaction
2021
Abstract Existing prestressed concrete structures suffer from degradation of prestressing for two main reasons: a defect of the sheath infills (cement grout) of bonded tendons, and corrosion of steel strands. These two causes, often concomitant, lead to a reduction over time of the effectiveness of initial prestressing, in addition to the ordinary tension losses due to concrete shrinkage and creep, and to steel relaxation. In many cases a consequence of bad grouting in bonded tendons is that the structure shows an intermediate behavior between that of external prestressing and that of internal bonded prestressing. This, added to damage to wires due to corrosion, makes it essential for the d…
Mix design and mechanical performance of geopolymeric binders and mortars using biomass fly ash and alkaline effluent from paper-pulp industry
2019
Abstract This work investigates the use of biomass fly ash (BFA) and an alkaline effluent (AEF), both generated from the Kraft pulp industry, in the preparation of geopolymeric binders and mortars for construction applications. BFA replaced the metakaolin (MK) while the AEF substituted the distilled water used to dissolve NaOH pellets. The mix design aims to maximize the amount of both the wastes and to optimize the materials properties, such as workability and mechanical performance. At the same time, also the environmental impact decreases enhancing the materials' sustainability and facilitating the circular economy. For the previously optimized BFA/MK ratio (70/30 wt.%) several NaOH/Na2S…
The effect of polycations on early cement paste
2010
International audience; This paper studies the possibility for improving the ductility of cement based materials by means of oligocationic additives. Actually, the setting of cement is due to ionic correlation forces between highly negatively charged C-S-H nanoparticles throughout a calcium rich solution. The main drawback of this strong attraction is its very short range that results in low elastic deformation of hydrated cementitious materials. A way to enlarge the attraction range between C-S-H particles would be to add cationic oligomers that would compete with calcium ions modifying the ionic correlation forces via a bridging mechanism of longer range, which could lead to a more ductil…
Experimental in situ behaviour of unreinforced masonry elements retrofitted by pre-tensioned stainless steel ribbons
2014
Abstract The results of in situ tests carried out on unreinforced and reinforced poor rubble masonry full-scale walls in the earthquake prone Messina (Italy) area are presented and discussed. This experimental research was aimed at the assessment of the in plane shear behaviour of ancient masonry strengthened with an innovative system for masonry and retrofitting of reinforced concrete element constituted by three-dimensional pre-tensioned stainless steel ribbons. A comparison between different strengthening configurations was made in order to characterise the behaviour of masonry panels under shear-compression load, focusing attention on the diagonal cracking failure mode. The effectivenes…
Improvements in aggregate-paste interface by the hydration of steelmaking waste in concretes and mortars
2019
[EN] The objective of the experimental work is to study the mechanical properties in self-compacting concretes (SCC) in which part of the limestone aggregate has been replaced by granulated blast furnace slag (GBFS) in different percentages ranging from 0% to 60%. The results show that at early ages the SCC with the largest content in slag tend to have lower compressive strengths due to the poor compacting of the aggregates, although in the long-term their strength increases due to the reactivity of the slag. In fact, at the age of 365 days, the mortars made with the substitution of 50% of cement by ground GBFS reach compressive strength similar to that of the mortar made with 100% of cemen…
Induced Modification of Flexural Toughness of Natural Hydraulic Lime Based Mortars by Addition of Giant Reed Fibers
2020
Abstract Nowadays, there is a growing need to reduce the environmental impact generated by the use of inorganic materials for building applications. The aim of this work is to investigate the bio-lime based mortar flexural toughness improvement due to the addition of common reed fibers (Arundo donax L.) in order to evaluate their possible application as ductile eco-compatible prefabricated bricks or laying and joint mortars for masonry. Different sets of specimens were tested by varying the fiber weight content and the fiber length. Moreover, chemical treatments with Linseed Oil and Polyethylene glycol (PEG) were performed to improve the physical and mechanical properties of the fibers as w…
Masonry columns confined with fabric reinforced cementitious matrix (FRCM) systems: A round robin test
2021
Abstract The conservation and the preservation of existing masonry buildings, most of them recognized as cultural heritage, require retrofitting techniques that should reduce the invasiveness and assure reversibility and compatibility with the substrate. In this perspective, the strengthening system should be able to improve the bearing capacity of the structural member and, at the same time, to assure mechanical and material compatibility. The use of Fabric Reinforced Cementitious Matrix (FRCM) composites is now recognized to be suitable for these purposes. Indeed, the inorganic matrix has comparable properties with respect to the existing historical mortars while the fabric has relevant t…
Behavior of fiber-reinforced concrete columns under axially and eccentrically compressive loads
2010
An experimental investigation into the behavior of 16 short, confined, reinforced concrete columns with and without steel fibers was carried out. The columns with square sections had a concrete core 165 x 165 mm (6.49 x 6.49 in.) at the midsection and were hunched at the ends to apply eccentric loading and prevent boundary effects. The specimens were tested to failure at different strain rates under two loading schemes: concentric compression and eccentric compression with a constant eccentricity. The axial load and axial strains were obtained to evaluate the effects of the presence of steel fibers, the thickness of the cover concrete, and the eccentricity of the applied axial load. The com…
Stainless steel grids for confinement of clay brick masonry columns
2016
This work presents the results of an experimental investigation on the behavior of 21 solid clay brick columns internally strengthened by stainless steel grids placed in the horizontal joints of mortar. This reinforcing technique can be applied as a constructive technique for new construction or as a retrofitting technique for existing structures (old structures to be reconstructed by original constructive method and internal reinforcement). Monotonic compressive loading tests were carried out under concentric and eccentric load. The effects of different numbers of steel grids and eccentricity of the external load were examined. Also, a detailed characterization of the constituent materials…