Search results for "C120"
showing 10 items of 297 documents
Failure Analysis of a Humeral Shaft Locking Compression Plate—Surface Investigation and Simulation by Finite Element Method
2019
A case study of a failed humeral shaft locking compression plate is presented, starting with a clinical case where failure occurred and an implant replacement was required. This study uses finite element method (FEM) in order to determine the failure modes for the clinical case. Four loading scenarios that simulate daily life activities were considered for determining the stress distribution in a humeral shaft locking compression plate (LCP). Referring to the simulation results, the failure analysis was performed on the explant. Using fracture surface investigation methods, stereomicroscopy and scanning electron microscopy (SEM), a mixed mode failure was determined. An initial fatigue failu…
Surface Reflectance: An Optical Method for Multiscale Curvature Characterization of Wear on Ceramic–Metal Composites
2020
Surface gradient characterization by light reflectance (SGCLR) is used for the first time for multiscale curvature calculations and discrimination of worn surfaces on six damaged ceramic&ndash
Bivariate analysis of taekwondo actions: The effectiveness of techniques and tactics in an Olympic taekwondo championship.
2020
This paper describes the effectiveness of technical-tactical actions performed during a tournament. A total of 14,145 actions of the 2012 London Olympic Games were analysed. Differences emerged in the use of tactics, techniques, zones, legs and guard to score. Regarding tactics, anticipatory counterattacks were the most effective for scoring one and three points. Circular techniques were the most effective for scoring one point, linear to score three points, and spin techniques to score two and four points. Actions to the chest results in a score of one to two points and actions to the head in a score of three to four points. The rear leg was more effective in scoring one, two and four poin…
Comparison of lower limb segments kinematics in taekwondo kick. an approach to the proximal to distal motion
2015
Abstract In taekwondo, there is a lack of consensus about how the kick sequence occurs. The aim of this study was to analyse the peak velocity (resultant and value in each plane) of lower limb segments (thigh, shank and foot), and the time to reach this peak velocity in the kicking lower limb during the execution of the roundhouse kick technique. Ten experienced taekwondo athletes (five males and five females; mean age of 25.3 ±5.1 years; mean experience of 12.9 ±5.3 years) participated voluntarily in this study performing consecutive kicking trials to a target located at their sternum height. Measurements for the kinematic analysis were performed using two 3D force plates and an eight came…
Understanding Action and Adventure Sports Participation—An Ecological Dynamics Perspective
2017
© 2017, The Author(s). Previous research has considered action and adventure sports using a variety of associated terms and definitions which has led to confusing discourse and contradictory research findings. Traditional narratives have typically considered participation exclusively as the pastime of young people with abnormal characteristics or personalities having unhealthy and pathological tendencies to take risks because of the need for thrill, excitement or an adrenaline ‘rush’. Conversely, recent research has linked even the most extreme forms of action and adventure sports to positive physical and psychological health and well-being outcomes. Here, we argue that traditional framewor…
Activity profile, PlayerLoad™ and heart rate response of Gaelic football players : A pilot study
2019
The objectives of this study were to; quantify positional differences in the activity profiles of Gaelic football players and to evaluate decrements in physical performance during a pre-season competition. Global positioning system (GPS) data was recorded from 36 players from 3 teams across 5 games. The relative distance covered in locomotor activities, peak speed, relative PlayerLoad™ (PL.min -1 )and heart rate responses were evaluated between playing positions and across match periods using a mixed model analysis. The mean relative distance of 92.4 ± 23.3 m.min -1 covered,comprised 28.4 ± 10.2 m.min -1 of high intensity running (m.min -1 ≥4.0 m.s -1 ) and 9.9 ± 3.9 m.min -1 of very high i…
The Influence of Hyaluronic Acid Biofunctionalization of a Bovine Bone Substitute on Osteoblast Activity In Vitro
2021
Bovine bone substitute materials (BSMs) are used for oral bone regeneration. The objective was to analyze the influence of BSM biofunctionalization via hyaluronic acid (HA) on human osteoblasts (HOBs). BSMs with ± HA were incubated with HOBs including HOBs alone as a negative control. On days 3, 7 and 10, cell viability, migration and proliferation were analyzed by fluorescence staining, scratch wound assay and MTT assay. On days 3, 7 and 10, an increased cell viability was demonstrated for BSM+ compared with BSM− and the control (each p ≤ 0.05). The cell migration was enhanced for BSM+ compared with BSM− and the control after day 3 and day 7 (each p ≤ 0.05). At day 10, an accelerated wound…
Characterization and Evaluation of Hydrothermal Liquefaction Char from Alkali Lignin in Subcritical Temperatures.
2021
An evaluation of hydrothermal liquefaction (HTL) char is investigated in this work. Morphological studies, N2 adsorption behavior, FTIR analysis, thermal behavior, and elemental composition are studied. The HTL char yield showed an increase with higher operating temperatures. It increased from 11.02% to 33% when the temperature increased from 573 K to 623 K. At lower temperatures, the residence time showed an impact on the yield, while close to the critical point, residence time became less impactful. Elemental analysis showed that both higher operating temperatures and longer residence times increased the nitrogen content of the chars from 0.32% to 0.51%. FTIR analysis suggested the char b…
Improving the Performance of Steel Machining Processes through Cutting by Vibration Control
2021
Machining processes through cutting are accompanied by dynamic phenomena that influence the quality of the processed surfaces. Thus, this research aimed to design, make, and use a tool with optimal functional geometry, which allowed a reduction of the dynamic phenomena that occur in the cutting process. In order to carry out the research, the process of cutting by front turning with transversal advance was taken into account. Additionally, semi-finished products with a diameter of Ø = 150 mm made of C45 steel were chosen for processing (1.0503). The manufacturing processes were performed with the help of two tools: a cutting tool, the classic construction version, and another that was the i…
Vacancy Defects in Ga2O3: First-Principles Calculations of Electronic Structure
2021
This research was funded by the Science Committee of the Ministry of Education and Science of the Republic of Kazakhstan (Grant No. AP08856540) as well as by the Latvian research council via the Latvian National Research Program under the topic ?High-Energy Physics and Accelerator Technologies?, Agreement No: VPP-IZM-CERN-2020/1-0002 for A.I. Popov. In addition, J. Purans is grateful to the ERAF project 1.1.1.1/20/A/057 while A. Platonenko was supported by Latvian Research Council No. LZP-2018/1-0214. The authors thank A. Lushchik and M. Lushchik for many useful discussions. The research was (partly) performed in the Institute of Solid State Physics, University of Latvia ISSP UL. ISSP UL as…