Search results for "CER"
showing 10 items of 24496 documents
Formation of translucent nanostructured zirconia ceramics
2021
Abstract In this work the mechanisms that affect the optical transparency of nanostructured translucent ZrO2 ceramics are studied. The translucent ceramic samples were obtained from a low agglomeration nanosized powder at low pressure and low temperature sintering. Even low pressures cause structural changes and defect creation in the nanocrystals. Annealing was used to study the grain formation, structure and impact of defects. Significant changes in translucency were observed with increase in pore size. In order to further understand the defect creation, the obtained ceramics were doped with Er3+ ions and studied optically. Photoluminescence studies revealed a change in the ratio of green…
Aqueous Corrosion of the GeSe4 Chalcogenide Glass: Surface Properties and Corrosion Mechanism
2009
International audience; The aqueous corrosion behavior of the GeSe4 glass composition has been studied over time under various conditions (temperature and pH). The evolution of the surface topography by atomic force microscopy and properties such as surface hardness and reduced modulus, as well as the optical transmission in the 1-16 μm window, have been measured as a function of time spent in the corrosive solution. It was found that even if the glass reacts at room temperature, its optical transparency was barely affected. Nevertheless, the durability of GeSe4 was found to be drastically affected by an increase of both temperature and pH. Furthermore, pure selenium nanoparticles were form…
Interface evolution during magnetic pulse welding under extremely high strain rate collision: mechanisms, thermomechanical kinetics and consequences
2020
Abstract Magnetic pulse welding enables to produce perplexing interfacial morphologies due to the complex material response during the high strain rate collision. Thus, a thermomechanical model is used in this study to investigate the formation mechanism of the wake, vortex, swirling and mesoscale cavities with the increase of the impact intensity at the interface. The formation of these interfacial features are difficult to characterize by insitu methods, thus the origin of phenomena still remain a subject of open discussion. Our studies identify the governing mechanisms and the associated thermomechanical kinetics, which are responsible for the formation mechanism of interfacial features.…
Deposition of binder-free oxygen-vacancies NiCo2O4 based films with hollow microspheres via solution precursor thermal spray for supercapacitors
2019
Abstract Hollow micro-/nanostructures and oxygen vacancies are highly desirable for supercapacitors due to high active surface area and outstanding electrochemical properties. In order to benefiting from the both effect, binder-free oxygen-vacancies NiCo2O4 based films with hollow microspheres were pioneering directly deposited via one kind thermal spray technology, named solution precursor thermal spray (SPTS) process. To our best knowledge, the rapid one-step SPTS route was firstly employed to synthesize and deposit NiCo2O4 films for supercapacitor applications. The CV data clearly demonstrated that the specific capacitances of more oxygen-deficient NiCo2O4 electrodes with hollow microsph…
Effect of surface disorder on the domain structure of PLZT ceramics
2017
ABSTRACTPb1-xLax(Zr0.65Ti0.35)1-x/4O3 (PLZT x/65/35) ceramics were studied by Piezoresponse Force Microscopy in order to understand the origin of domain structure as a function of La content. We show that the domain topology is mainly determined by the composition and grain size. The characteristic correlation length decreases with increasing La content, being sensitive also to the synthesis method. The behavior of the correlation length is linked to the macroscopic properties, showing a strong increase of disorder with La doping. The roughness exponent for the domain wall in PLZT 9/65/35 is close to 2/3 indicating 1D character of domain walls in relaxors.
Metrological Properties of the Test Setup for Determination Shielding Effectiveness of the Industrial Cable Connectors
2017
Abstract The paper presents results related to assessment of the repeatability and reproducibility of the measurement test setup for determination the relative value of the shielding effectiveness coefficient of the industrial connectors. The construction of the proposed test setup, the measurement method and the procedure for the analysis of measurement results were described. To determine the value of the repeatability and reproducibility coefficient, the two–way analysis of variance was used, which additionally allows for an assessment of the influence of individual sources of variance. The measurements and their analysis were conducted for several frequencies in the range up to 1 GHz. A…
Thermal oxidation of the intermetallic phases Al 8 Mo 3 and AlMo 3
2017
Abstract The thermal oxidation reactions of the intermetallic phases Al8Mo3 and AlMo3 were investigated and analyzed by ex-situ powder-x-ray diffraction (XRD), difference thermal analysis (DTA), thermogravimetry (TGA), and infrared spectroscopy (IR). The initial oxidation reactions in air were found to yield Al2O3 and AlMo3 in the case of Al8Mo3 (Tonset =725 °C), and MoO3 as well as Al8−xMo3 (Tonset =435 °C) for the pure intermetallic phase AlMo3, respectively. Thus, both intermetallic phases are coexisting in an equilibrium within a temperature range of 300 °C under oxidizing conditions. The formation of β-Al2(MoO4)3 followed the second oxidizing process of the respective minority componen…
High sensitivity characterization of the nonlinear electric susceptibility of a glass ceramic in the microwave range
2019
The nonlinear electric susceptibility of a glass ceramic is characterized in the microwave range by measuring intermodulation of two high-power signals. To achieve the necessary sensitivity for dielectric nonlinearities, the setup ensures that the measured intermodulation can be ascribed to the material under test while all other intermodulation sources are suppressed. This is achieved by coupling three dielectric resonators in a cut-off waveguide. The third order nonlinearity of the glass ceramic is found to be χ3/er = (1.6 ± 0.8) × 10−15 m2/V2 at 950 MHz. The magnitude is comparable to the previously measured high-end sintered ceramics. The power of the intermodulation signal as a functio…
Quantification of relaxor behavior in (1 − x)Na0.5Bi0.5TiO3 – xCaTiO3 lead-free ceramics system
2019
Abstract This work examines the relaxor behavior of lead-free ceramic (1 − x)Na0.5Bi0.5TiO3–xCaTiO3 systems. A stable rhombohedral (R3c) phase is detected at room temperature for all compositions by XRD and Raman spectroscopy. Relaxor behavior was observed in the temperature range 300 K - 400 K for all materials. Ceramics exhibit normal ferroelectric properties at room temperature, and then they develop relaxor characteristics with increasing temperature showing the same dispersive properties. This work quantifies the relaxor phenomenon at low temperature. For instance, the maximum temperature of relaxor and the order of dispersion were determined at the strongest dispersion. Finally, the s…
Estimation des incertitudes de mesure sur bras polyarticulé portable par méthode de Monte Carlo
2013
International audience; Les bras polyarticulés portables ont progressivement évolué et sont de plus en plus utilisés dans l’industrie. Cependant, à l’heure actuelle, la traçabilité de ces dispositifs est difficile à effectuer et les incertitudes de mesures relatives à l’utilisation de ces appareils ne sont pas quantifiées. Le travail mené consiste à déterminer les incertitudes de mesures associées à la quantification, par un bras polyarticulé portable, des caractéristiques géométriques et dimensionnelles d’une pièce mécanique. Les travaux visant à élaborer un modèle d’incertitude de mesure, sont basés sur la méthode de Monte Carlo du supplément 1 du Guide pour l'expression de l'incertitude …