Search results for "CERAMICS"
showing 10 items of 1599 documents
FORMATION OF FRACTAL MICRO- AND NANO-STRUCTURES IN CERAMIC TANTALUM PENTOXIDE UNDER CONCENTRATED FLUX OF LIGHT AND THEIR EFFECT ON THERMAL EXPANSION
2009
ABSTRACT Oxides of weak thermal expansion are the basis for stable ceramics and artefacts resistant to sharp cyclic variations of temperature. For technical applications is a wide interest in high-temperature materials of low or negative thermal expansion and, particularly, in studies of the micromechanisms in Ta2O5. Thermal expansion of ceramic pentoxides of tantalum is affected by conditions under which they are formed. After treatment by concentrated light flows anomalous segments of zero and even negative thermal expansion appear in ceramics of Ta2O5. The effect of treatment by concentrated light flux on formation of fractal nano-structures and thermal expansion of ceramic tantalum pent…
On the Elastic Behavior of a Cross-Ply Composite Pin-Joint with Clearance Fits
1999
The effect of pin/hole clearance fits on the elastic membranal behavior of a cross-ply fiber glass-reinforced epoxy laminate plate loaded in tension through a pin is examined by a finite element nonlinear contact analysis. No a priori assumption is made on the distribution of the contact pressure on the surface of the hole. Friction effects are not included. The numerical results correlate well with Hertzian theory of contact. It is demonstrated that clearance increases the peak compressive stress in the plate up to a factor of 3000% with respect to the perfect-fit case. Clearance also shifts the location of the peak tensile stress towards the pin/hole contact arc and decreases its magnitu…
On the Effect of Interference Fits in Composite Pin-Joints
1999
The Finite Element Method is used to determine the effect of pin/hole interference fits on the elastic membranal behavior of an orthotropic plate loaded in tension through a pin. A complete contact analysis is performed to handle the nonlinear contact problem. The study encompasses two levels of interference fits, two degrees of anisotropy of the plate, and two load levels. Friction effects are not included. Experimental results from Digital Speckle Pattern Interferometry are also presented. It is shown that the stress changes in the plate vary linearly with load when no pin/plate separation occurs. It is also shown that interference fits can have beneficial effects on the static and fatig…
Analysis of the effect of a stress raiser on the strength of a UD flax/epoxy composite in off-axis tension
2014
The effect of stress raisers in the form of a slit-like notch and an open circular hole on the tensile strength of a quasi-UD flax-fiber-reinforced composite is studied experimentally. A finite fracture mechanics approach is applied to determine the intralaminar fracture toughness of the composite and to predict the strength in the presence of stress concentration. Reasonably good agreement of the notch effect predicted using finite fracture mechanics with a coupled strength and toughness fracture criterion and test results is demonstrated.
A Study on the Effects of Clearance and Interference Fits in a Pin-Loaded Cross-Ply FGRP Laminate
1998
The elastic behavior of a cross-ply fiber glass-reinforced epoxy laminate loaded in tension through a pin fitted with clearance and interference is examined. A nonlinear contact analysis using the Finite Element Method and an experimental study by Speckle Interferometry are performed, showing fairly good correlation. An interesting comparison is performed between FEM results and Hertzian contact theory. Major conclusions are: (I) clearance causes high compressive stress in the bearing area, and does not influence the peak tensile stress; (2) interference has beneficial effects on the joint, as (a) it lowers the peak circumferential stress, and (b) it decreases the change of stress due to t…
Residual stresses and FCP prediction in FSW through a continuous FE model
2009
Abstract Residual stresses prediction is definitively a relevant and open issue in welding processes. In the last years, different numerical models are proposed by many researchers to predict the residual stress field in FSW butt joint. However, most of these works are based on properly tuned analytical models and neglect the effect of the mechanical action due to the presence of the tool pin. In the present paper, a continuous 3D FE model, which was previously developed by some of the authors, was used to simulate the FSW process of butt joints with a single block approach, and predict the residual stress field by considering both thermal and mechanical actions. Then, the residual stress e…
Glass fibre strength distribution determined by common experimental methods
2002
The tensile strength of brittle fibres is routinely described by the Weibull distribution. The parameters of the distribution can be obtained from tests on single fibres and fibre bundles or from model composite tests. However, there is growing evidence that the distribution parameters obtained by different experimental techniques differ systematically. In order to investigate the possible causes of such discrepancies, single-fibre tension, fibre bundle, and single-fibre fragmentation tests are employed in this study to obtain strength distribution of commercial E-glass fibres. The results reveal parameter dependence on the approach used to extract the distribution parameters from experimen…
Effectiveness of stirrups and steel fibres as shear reinforcement
2004
This paper presents the results of experimental tests carried out on rectangular simply supported beams made of hooked steel fibre reinforced concrete with and without stirrups, subjected to two-point symmetrically placed vertical loads. The tests, carried out with controlled displacements, allow one to record complete load-deflection curves by means of which it is possible to deduce information on dissipative capacity and ductile behaviour up to failure. Depending on the amount of transverse reinforcement, volume fraction of fibres added in the mix and shear span, the collapse mechanism is due to predominant shear or flexure, thus showing the influence of the aforementioned structural para…
Toward high performance renewable agave reinforced biocomposites: Optimization of fiber performance and fiber-matrix adhesion analysis
2017
Abstract The increasing sensitivity toward the environmental pollution and the recent laws on the environmental protection, have led to an increasing attention to the so called biocomposites, i.e. to ecofriendly or renewable composite materials, obtained from biopolymers reinforced by natural fibers. Although the contribution of various works reported in literature, focused on biocomposites reinforced by agave fibers, such materials are still exclusively used in the automotive industry for non-structural applications, and the implementation of high performance biocomposites for semi-structural and structural applications, is an expected, but not yet reached objective. Therefore, the present…
Salt-fog spray aging of jute-basalt reinforced hybrid structures. Flexural and low velocity impact response
2017
Abstract In this work, a study on the aging resistance of jute and jute-basalt interply hybrid laminates exposed to salt-fog is presented with the aim to investigate the possibility to enhance the durability of natural fiber reinforced composites for marine application by a ply-substitution approach. In particular, jute and basalt/jute reinforced composite plates were manufactured by vacuum assisted resin infusion in two different staking sequences (i.e., intercalated and sandwich-like basalt-jute) and aged under salt fog conditions. The effects of the accelerated aging at increasing times on the mechanical response of laminates were assessed in both quasi static (three point bending) and d…