Search results for "CIRCUIT"
showing 10 items of 936 documents
Optimal matching between optical rectennas and harvester circuits
2017
This paper deals with optimal coupling issues between rectennas and harvesting circuits. An optical rectenna consists of a nanoantenna usually coupled with an ultra-high speed rectifier. These devices aim to receive and convert solar and thermal radiation in a DC voltage, while a harvester circuit provides the energy to be stored. The rectenna impedance is influenced both by its structure and by the rectifying diode, the harvester circuit impedance has to be matched to optimize the power transfer. The purpose of this contribution is to discuss the best impedance conditions by taking into account the constraints that are due to the individual devices the conversion system consist of. Finally…
Análisis de eficacia y repercusión hemodinámica de los dispositivos de protección embólica de red para intervenciones endovasculares en un modelo hem…
2020
El tratamiento endovascular de obstrucciones arteriales presenta un continuo desarrollo, ofreciendo excelentes resultados con una morbilidad reducida frente a la cirugía convencional. Sin embargo, la emisión inadvertida de micropartículas puede generar daños graves en los tejidos y órganos diana. En este sentido existe poca información acerca de los dispositivos de protección embolica de red (DPEr). El objetivo principal de este estudio consistió en analizar las diferencias entre DPEr de uso comercial en cuanto a su eficacia, además de las repercusiones hemodinámicas antes y después de la inyección de partículas en un símil in vitro diseñado para esta finalidad. Materiales y Métodos: Estudi…
Comparison between Focused Electron/Ion Beam-Induced Deposition at Room Temperature and under Cryogenic Conditions
2019
This article belongs to the Special Issue Multi-Dimensional Direct-Write Nanofabrication.
Design and simulation of efficient combinational circuits based on a new XOR structure in QCA technology
2021
AbstractQuantum-dot cellular automata (QCA), due to its unique characteristics like low power consumption, nanoscale design, and high computing speed is considered as an emerging technology, and it can be used as an alternative for CMOS technology in circuit design for quantum computers in the near future. XOR gate has many applications in the design of digital circuits in QCA. In this paper, an efficient novel structure of XOR gate is proposed in QCA. Also, a novel 1-bit comparator circuit, 1-bit full adder, binary to gray and gray to binary convertor code based on the proposed XOR is designed and simulated using QCADesigner 2.0.3. The simulation results demonstrated that the proposed stru…
A Simulation Analysis for Assessing the Reliability of AC/DC Hybrid Microgrids - Part II: Port Area and Residential Area
2021
This paper reports the second part of a simulation study with the aim of evaluating the ability of two portions of a hybrid AC/DC MV/LV network in maintaining their operation in off-grid mode during the loss of the main AC grid due to a failure. In particular, this paper follows a dual purpose: first, it analysis two microgrids in a residential area and a port zone capability of operating in islanded mode, applying a probabilistic approach, while there is different energy use cases, and second is to evaluate some reliability indicators.
Surface and interface effects on the current-voltage characteristic curves of multiwall carbon nanotube-Si hybrid junctions selectively probed throug…
2021
The possibility to increase the efficiency of photovoltaic (PV) cells based on hybrid carbon nanotube (CNT)–Si heterojunctions is related to the ability to control the chemical properties of the CNT–Si interface and of the CNT bundle layer. In spite of the encouraging performances of PV cells based on multiwall (MW) CNT, so far few efforts have been made in the study of this device compared to single wall (SW) CNT–Si interfaces. Here, surface and interface effects on the current–voltage characteristic curves of MW CNT–Si hybrid junctions are investigated through exposure to HF vapors and to 10 ppm-NO2 and compared to the effects detected in SW CNT–Si junctions. Quite similar results in term…
Accuracy of Computer-Aided Dynamic Navigation Compared to Computer-Aided Static Navigation for Dental Implant Placement: An In Vitro Study
2019
Aim: To analyze the accuracy capability of two computer-aided navigation procedures for dental implant placement. Materials and Methods: A total of 40 dental implants were selected, which were randomly distributed into two study groups, namely, group A, consisting of those implants that were placed using a computer-aided static navigation system (n = 20) (guided implant (GI)) and group B, consisting of those implants that were placed using a computer-aided dynamic navigation system (n = 20) (navigation implant (NI)). The placement of the implants from group A was performed using surgical templates that were designed using 3D implant-planning software based on preoperative cone-beam computed…
Synthetic approach to the design of wide-band microwave injection-locked amplifiers
2010
In this work, a synthesis-based approach to the realization of wide-band microwave injection-locked amplifiers (ILA) is proposed. To this purpose, a transmission-type topology is combined with a feedback structure in which the "core ILA" is intentionally separated from the output (power) amplifier. A modular, matched, design of individual building blocks of the core ILA is then adopted, which allows their first-approximation exact modeling in the dynamical complex-envelope domain, following the theory earlier developed by Calandra-Sommariva. On this basis, analytic expressions for the main operating characteristics of the ILA (such as the locking bandwidth under small signal operation) are …
Approach to the Design of Transmission-Type Injection-Locked Microwave Oscillators through Behavioral Block Modeling
2010
In this work, an attempt is made toward the development of a systematic design method for the performance- driven dimensioning of the various elements comprising the structure of modern transistor-based microwave injection- locked oscillators with transmission-type topologies (TILOs). The proposed approach is based on the use of appropriate diakoptics of the various circuit blocks into a matched environment, and their behavioral modeling in the fundamental- frequency dynamical complex envelope domain with the help of standard circuit and E.M. simulation CAD tools. This will permit, in the end, to obtain closed-form expressions for the main TILO performances in terms of the design parameters…
Effective Recovery Process of Copper from Waste Printed Circuit Boards Utilizing Recycling of Leachate
2020
AbstractThis study presents an optimized leaching and electrowinning process for the recovery of copper from waste printed circuit boards including studies of chemical consumption and recirculation of leachate. Optimization of leaching was performed using response surface methodology in diluted sulfuric acid and hydrogen peroxide media. Optimum leaching conditions for copper were found by using 3.6 mol L−1 sulfuric acid, 6 vol.% hydrogen peroxide, pulp density of 75 g L−1 with 186 min leaching time at 20°C resulting in complete leaching of copper followed by over 92% recovery and purity of 99.9% in the electrowinning. Study of chemical consumption showed total decomposition of hydrogen pero…