Search results for "CONST"

Enhanced superconductivity in atomically thin TaS2

2016

The ability to exfoliate layered materials down to the single layer limit has presented the opportunity to understand how a gradual reduction in dimensionality affects the properties of bulk materials. Here we use this top–down approach to address the problem of superconductivity in the two-dimensional limit. The transport properties of electronic devices based on 2H tantalum disulfide flakes of different thicknesses are presented. We observe that superconductivity persists down to the thinnest layer investigated (3.5 nm), and interestingly, we find a pronounced enhancement in the critical temperature from 0.5 to 2.2 K as the layers are thinned down. In addition, we propose a tight-binding …

Porcine Model for Deep Superior Epigastric Artery Perforator Flap Harvesting: Anatomy and Technique

2018

BACKGROUND Microsurgical training on rats before starting with clinical practice is a well-established routine. Animal model training is less widespread for perforator flaps, although these flaps represent a technical challenge. Unlike other flaps, they require specific technical skills that need to be adequately trained on a living model 1 : a cadaver is not enough because no bleeding, vessel damage, or vasospasm can be simulated. 2 The purpose of this study was to assess the suitability of the porcine abdomen as a training model for the deep inferior epigastric artery perforator (DIEAP) flap, commonly used in human breast reconstruction. METHODS A female swine (Sus scrofa domesticus, ssp;…

Continuity and Change in Cosmological Ideas in Spain Between the Sixteenth and Seventeenth Centuries: The Impact of Celestial Novelties

2010

The star which became visible in 1572 in the constellation of Cassiopeia (identified by twentieth-century astronomers as a Type I supernova), and the works and polemics to which it gave rise, marked an important stage in the abandonment of Aristotelian and medieval cosmology and their replacement by the idea of the infinite—or indefinite—universe of modern physics and astronomy.

Study of nucleation and growth processes of ettringite in diluted conditions

2020

Abstract Ettringite is a key compound of cementitious materials, formed during hydration that influences the rheological behavior of the cement paste. Despite its importance, ettringite formation has been poorly studied. In this work, nucleation and growth processes of ettringite were separately investigated. Ettringite nucleation was described using the Classical Nucleation Theory and an interfacial crystal-solution energy was determined. After the initial primary homogeneous nucleation, when the surface of already formed crystals was still low, the precipitation rate was shown to depend almost exclusively on the solution supersaturation. When the surface of crystals in suspension was gett…

Capacity constrained supply chains: a simulation study

2008

This paper explores the relationship between constrained capacity and supply chain performance. Six capacity constraint levels are studied under different inventory policies and information sharing strategies. The results suggest that an increment of production capacity, used in industry as local approach to manage increasing incoming orders, does not necessarily imply an improvement in customer service. In presence of information distortions, the strategy of augmenting production capacity can lead to satisfy at a higher cost an over-estimated market demand. The collaborative practices provide bullwhip effect dampening and inventory stability, and increase the ability of the structure to av…

Il confronto tra Supreme Court e dottrina inglese: un vento nuovo soffia a Westminster

2016

Optimization of the Surface Roughness Equation obtained by Al7136 End-Milling

2017

The aim of this paper is to optimize the regression equation of the surface roughness obtained by 7136 aluminium alloy machined by end-milling process. The surface roughness is dependent on certain process parameters, which can vary, causing in this way variations of the surface quality. The research method used in this paper is the experiment and the Taguchi design of experiment. The experiment was performed using an experimental stand, in which every step to get the purpose, is presented. The measurements were made using a portable surface roughness tester. In the first part of the paper the influence percentage of the involved parameters in the machining process, was determined. Then, a …

Atomistic Simulations of the LaMnO3 (110) Polar Surface.

2003

The results of atomic structure calculations, with a focus on the surface relaxation and polarization, are presented for the LaMnO3 (110) O-terminated polar surface. We compare results of the classical shell model calculations for four possible terminations, including (1 × 2) (110) surface reconstruction, and demonstrate that the latter has the lowest surface energy. The surface energy is saturated only when six to eight near-surface atomic planes are relaxed which is accompanied by the considerable dipole moments perpendicular to the surface. Results are compared with those for iso-structural BaTiO3 (110) surfaces.

Geometric Properties of the 3D Spine Curve

2003

Through a 3D reconstruction of the human back surface using structured light techniques, we study the properties of spine curve by means of a set of parameters related to measures commonly applied in medicine. In this way, descriptors for measuring the abnormalities in the projections of the front and sagittal planes can be computed. We build the spine curve in 3D and analyse the behaviour of the Frenet frame when along the curve the deformation processes in idiophatic scoliosis appear.

Algorithms for the calculation of the view factors between human body and rectangular surfaces in parallelepiped environments

1992

Abstract The thermal comfort conditions for people in moderate thermal environments are subjected to spatial changes, depending on the radiative exchanges of the human body with the surrounding surfaces. Radiative thermal exchanges are notably accounted for by means of the “view factors” between a person in a given posture and the surface of the enclosure. These important parameters can be evaluated by means of a large set of graphs by Fanger, for rectangular surfaces. But the handling of graphs could lead to reading errors. In this paper a simple algorithm is presented, which is able to compute the required view factors. A validation, by means of a comparison against experimental data, is …