Search results for "Carbide"

Interference Cancellation for LoRa Gateways and Impact on Network Capacity

2021

In this paper we propose LoRaSyNc (LoRa receiver with SyNchronization and Cancellation), a second generation LoRa receiver that implements Successive Interference Cancellation (SIC) and time synchronization to improve the performance of LoRa gateways. Indeed, the chirp spread spectrum modulation employed in LoRa experiences very high capture probability, and cancelling the strongest signal in case of collisions can significantly improve the cell capacity. An important feature of LoRaSyNc is the ability to track the frequency and clock drifts between the transmitter and receiver, during the whole demodulation of the interfered frame. Due to the use of low-cost oscillators on end-devices, a s…

A PARAMETERS’ SYNTHESIS OF GRINDING PROCESS MODELING FOR CARBIDE DRILLS DEEP HOLES AND SMALL DIAMETER

2013

Analysis of powdered tungsten carbide hard-metal precursors and cemented compact tungsten carbides using laser-induced breakdown spectroscopy

2007

Laser-induced breakdown spectroscopy (LIBS) has been applied to the direct analysis of powdered tungsten carbide hard-metal precursors and cemented tungsten carbides. The aim of this work was to examine the possibility of quantitative determination of the niobium, titanium, tantalum and cobalt. The investigated samples were in the form of pellets, pressed with and without binder (powdered silver) and in the form of cemented tungsten carbides. Several lasers and detection systems were utilized.

Solid-State Pyrolyses of Metal Phthalocyanines: A Simple Approach towards Nitrogen-Doped CNTs and Metal/Carbon Nanocables

2006

Solid-state pyrolysis of organometallic precursors has emerged as an alternative method for preparing carbon nanostructures such as carbon nanotubes (CNT) and carbon anions. The morphology of the tubes can be controlled by the nature of the precursors and the pyrolysis procedures, and micrometer long nanotubes, composed of metal carbide wires encased in a graphitic sheath. Cobalt phthalocyanine (CoPc) as well as iron phthalocyanine were pyrolyzed at different temperatures to obtain CNTs. HRTEM and energy-dispersion X-Ray analysis disclosed that the core consisted of long, iron-containing single crystals and that the core was fully surrounded by crystallized graphic carbon. Iron-filled carbo…

From nitrides to carbides: topotactic synthesis of the η-carbides Fe3Mo3C and Co3Mo3C

2004

The molybdenum bimetallic interstitial carbides Fe(3)Mo(3)C and Co(3)Mo(3)C have been synthesized by temperature-programmed reaction (TPR) between the molybdenum bimetallic interstitial nitrides Fe(3)Mo(3)N and Co(3)Mo(3)N and a flowing mixture of CH(4) and H(2) diluted in Ar. These compounds have been characterized by X-ray diffraction, laser Raman spectroscopy, elemental analysis, energy dispersive analysis of X rays, thermal analysis (in air) and scanning electron microscopy (field emission). Their structures have been refined from X-ray powder diffraction data. These carbides crystallize in the cubic system, space group Fd3m[a= 11.11376(6) and 11.0697(3)[Angstrom] for Fe and Co compound…

THE INFLUENCE OF TOOL STIFFNESS OF THE LIFETIME OF THE INSERTS IN INTERRUPTED CUTTING OPERATIONS

1989

ABSTRACT In the present paper the influence exerted by the stiffness of the tool-workpiece system under working conditions on tool life up to the fracture of carbide inserts in interrupted cutting is investigated. It is shown how, with the increase in compliance of the system, there is a corresponding increase in the average tool life of the insert which is greater the lesser the cutting speed. The results of tests carried out indicate as a possible cause the amount of damage evident in the successive phase of tool engagement with the workpiece. It was observed how, in this phase, the tool, vibrating at the same rate as the toolholder produces alternations in the cutting force. This effect …

Wear rates and wear mechanisms of alumina-based tools cutting steel at a low cutting speed

1997

Abstract Three ceramic insert materials, zirconia-toughened alumina (Al 2 O 3 –7vol%ZrO 2 ), mixed-based alumina (Al 2 O 3 –TiN–TiC–ZrO 2 ) and alumina reinforced with SiC whiskers (Al 2 O 3 –SiC w ), were used to cut AISI 1040 steel at 3.9 m s −1 . In addition, a traditional grade P10 insert (WC–TiC–Co) was tested. The lifetimes, according to KT/KM and VB B criteria, were determined using a profilometer and by image processing. The worn zones were observed with scanning electron microscopy techniques. Adhesion and plastic deformation were dominant wear mechanisms in zirconia-toughened alumina, mixed-based alumina and sintered carbide P10, both in the craters and in the cutting edges. As we…

Metal Matrix Composites - Mmc - Turning: Comparison of Tool Materials

2002

The main properties required to the modem cutting tools to be employed in production, are both high wear resistance and chemical stability. In this last years, in the machining of MMCs several kinds of coated tools have been developed; they are characterized by high hardness to resist to the relevant strength and abrasive action of the reinforce fibers or particles, arranged inside the matrix. In turning of MMC the employ of Tungsten Carbide tools coated with Polycrystalline Diamond (PCD) have shown to be very effective, whereas they are very expensive thus increasing the production costs.

Laser irradiation of carbon–tungsten materials

2014

Carbon–tungsten layers deposited on graphite by thermionic vacuum arc (TVA) were directly irradiated with a femtosecond terawatt laser. The morphological and structural changes produced in the irradiated area by different numbers of pulses were systematically explored, both along the spots and in their depths. Although micro-Raman and Synchrotron-x-ray diffraction investigations have shown no carbide formation, they have shown the unexpected presence of embedded nano-diamonds in the areas irradiated with high fluencies. Scanning electron microscopy images show a cumulative effect of the laser pulses on the morphology through the ablation process. The micro-Raman spatial mapping signalled an…

Growth of titanium oxynitride layers by short pulsed Nd:YAG laser treatment of Ti plates: Influence of the cumulated laser fluence.

2009

International audience; Titanium oxynitride layerswere formed by surface laser treatment of Ti plates in air using a Nd:YAG laser source of short pulse duration about 5 ns. The cumulated laser fluence was varied in the 100–1200 J cm2 range and its influence on the composition and the structure of the formed layers was studied by different characterization techniques providing physico-chemical and structural information. It was shown that the laser treatment induces the insertion of light elements as O, N and C in the formed layer with the amount increasing with the laser fluence. The in-depth composition of the layers and the co-existence of different phases were also studied. The way in wh…