Search results for "Carbon film"

Anodic Electro Deposition of CeO2 and Co-Doped CeO2 Thin Films

2013

CeO2 and Co containing CeO2 thin films were deposited on indium tin oxide and stainless steel by anodic electrodeposition. Scanning electron microscopy showed that the films are flat and show globular morphology and cracks resulting from volume shrinking. According to XRD and Raman Spectroscopy pure ceria layers are crystalline, while the presence of Co induces the formation of amorphous films. The good adhesion and the compactness allowed the photoelectrochemical characterization of the films. A band gap value of 2.9 eV was estimated for CeO2, while slightly higher values (̃3.0 eV) were estimated for Co containing films. A mechanism for ceria anodic electrodeposition is proposed and discus…

Antibacterial and barrier properties of oriented polymer films with ZnO thin films applied with atomic layer deposition at low temperatures

2014

Abstract Concerns on food safety, and need for high quality and extended shelf-life of packaged foods have promoted the development of antibacterial barrier packaging materials. Few articles have been available dealing with the barrier or antimicrobial properties of zinc oxide thin films deposited at low temperature with atomic layer deposition (ALD) onto commercial polymer films typically used for packaging purposes. The purpose of this paper was to study the properties of ZnO thin films compared to those of aluminum oxide. It was also possible to deposit ZnO thin films onto oriented polylactic acid and polypropylene films at relatively low temperatures using ozone instead of water as an o…

Growth of manganese sulfide (α-MnS) thin films by thermal vacuum evaporation: Structural, morphological and optical properties

2016

Abstract MnS thin films have been successfully prepared by thermal evaporation method at different substrate temperatures using different masses of MnS powder. The prepared films were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and UV–visible spectrophotometry. The XRD measurements show that the films crystallized in the pure α-MnS for substrate temperatures above 100 °C. The optical bandgap of thin films is found to be in the range of 3.2–3.3 eV. A factorial experimental design was used for determining the influence of the two experimental parameters on the films growth.

Mechanical properties of nanostructured carbon layers grown by CVD and PLD techniques

2010

Pulsed laser deposition (PLD) and chemical vapour deposition (CVD) have been proven to be among the most successful techniques for growing the entire spectrum of carbon films, which can be used in a wide range of technical applications. Here an investigation has been performed to explore the effect of different growing techniques (PLD and CVD) and process parameters (such as deposition time and substrate type) on the films' morphology and mechanical properties. The mechanical properties of the grown thin films were characterised by means of nano/micro indentation and scratch test techniques. It was observed that the thickness of the Al2O3 interlayer (between the Fe catalyst nanoparticles an…

Epitaxial growth and properties of (001)-oriented TbBaCo2O6−δ films

2008

Thin epitaxial films of TbBaCo2O6−δ cobaltites have been synthesized using pulsed laser deposition. It was found that the film properties are extremely sensitive to the oxygen pressure during deposition, temperature of the substrate, and the cooling rate. Growth parameters were optimized for δ≈0.5 films with ordered Tb and Ba ions, as well as oxygen vacancies. The properties of these c-axis oriented films are similar to bulk TbBaCo2O5.5: they show a metal-insulator phase transition at TMI≈350 K, ferromagnetic order below TC=285 K, and antiferromagnetism at T<Ti≈230 K.

Studies on atomic layer deposition of IRMOF-8 thin films

2015

Deposition of IRMOF-8 thin films by atomic layer deposition was studied at 260–320 C. Zinc acetate and 2,6-naphthalenedicarboxylic acid were used as the precursors. The as-deposited amorphous films were crystallized in 70% relative humidity at room temperature resulting in an unknown phase with a large unit cell. An autoclave with dimethylformamide as the solvent was used to recrystallize the films into IRMOF-8 as confirmed by grazing incidence x-ray diffraction. The films were further characterized by high temperature x-ray diffraction (HTXRD), field emission scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR), time-of-flight elastic recoil detection analysis (TOF-…

Superconducting hollow and solid fibers and thin films of YBa2Cu3OX from a polymeric precursor

1990

Atomic layer deposition of WO3 thin films using W(CO)6 and O3 precursors

2012

Here we report a new atomic layer deposition (ALD) process for WO3 thin films based on W(CO)6 as a tungsten source and ozone as a source of oxygen. A narrow ALD temperature window is found at 195–205 °C for WO3 with a deposition rate of 0.23 A per cycle. As-deposited films are partially crystalline with root mean square (rms) roughness values of 4.7 nm for 90 nm thick films; annealing the films at 600–1000 °C under oxygen or nitrogen atmospheres enhances the degree of crystallinity considerably. Our results show that the straightforward ALD chemistry of carbonyl compounds and ozone is applicable to the deposition of WO3 thin films.

Economical device for measuring thickness of a thin polymer film

1994

An inexpensive device (about $2K) for thickness measurements of thin (<1 μm) polymer films has been constructed. The homogeneous film is placed on a bulk substrate and three semiconductor lasers of different wavelengths are used to measure the reflectances at normal incidence. The thickness can be deduced with typically 4–8 nm uncertainty.

Effect of Boron Doping on the Wear Behavior of the Growth and Nucleation Surfaces of Micro- and Nanocrystalline Diamond Films

2016

B-doped diamond has become the ultimate material for applications in the field of microelectromechanical systems (MEMS), which require both highly wear resistant and electrically conductive diamond films and microstructures. Despite the extensive research of the tribological properties of undoped diamond, to date there is very limited knowledge of the wear properties of highly B-doped diamond. Therefore, in this work a comprehensive investigation of the wear behavior of highly B-doped diamond is presented. Reciprocating sliding tests are performed on micro- and nanocrystalline diamond (MCD, NCD) films with varying B-doping levels and thicknesses. We demonstrate a linear dependency of the we…