Search results for "Cobaltite"
showing 7 items of 7 documents
Interface reactivity study between La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF) cathode material and metallic interconnect for fuel cell
2011
Abstract Interface reactivity between La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF) cathode material and metallic interconnect (Crofer22APU) was investigated in laboratory air at 700 °C. Due to the interconnect geometry, two interfaces have been analysed: (i) interconnect rib/cathode interface (physically in contact); (ii) the interface under the channel of interconnect. In both cases, formation of a parasite phase was observed after various ageing treatments (20 h, 100 h and 200 h). However, the growth of the determined SrCrO4 parasite phase depends on interface type and on ageing time. Two different mechanisms have been established in function of interface type: (i) SrCrO4 phase was formed after solid …
La1-xSrxCo1-yFeyO3-delta perovskites: Preparation, characterization and solar photocatalytic activity
2015
Abstract LaCoO3 perovskites substituted by Sr at the A site and/or by Fe at the B site have been prepared by the citrate method. Characterizations by several techniques, such as specific surface area (BET method), XRD, TPR, SEM, UV–vis in DRS mode, XPS and TGA analyses, have been performed. The so prepared La1−xSrxCo1−yFeyO3−δ perovskites are semiconductor materials showing band gap energy values from 1.9 to 3.2 eV. They displayed solar photocatalytic activity for the 2-propanol degradation in gas–solid regime. The photocatalytic results suggest that the perovskites containing Fe are less active and the activity decreases by increasing the Fe content, however the presence of iron avoids the…
Segmented Thermoelectric Oxide-Based Module for High-Temperature Waste Heat Harvesting
2015
We report a high-performance thermoelectric (TE) oxide-based module using the segmentation of half-Heusler Ti_(0.3)Zr_(0.35)Hf_(0.35)CoSb_(0.8)Sn_(0.2) and misfit-layered cobaltite Ca_3Co_4O_(9+δ) as the p-leg and 2 % Al-doped ZnO as the n-leg. The maximum output power of a 4-couple segmented module at ΔT=700 K attains a value of approximately 6.5 kW m^(−2), which is three times higher than that of the best reported non-segmented oxide module. The TE properties of individual legs, as well as the interfacial contact resistances, were characterized as a function of temperature. Numerical modeling was used to predict the efficiency and to evaluate the influence of the electrical and thermal lo…
Strontium and iron-doped barium cobaltite prepared by solution combustion synthesis: exploring a mixed-fuel approach for tailored intermediate temper…
2013
Ba0.5Sr0.5Co0.8Fe0.2O3-? (BSCF) powders were prepared by solution combustion synthesis using single and double fuels. The effect of the fuel mixture on the main properties of this well-known solid oxide fuel cell cathode material with high oxygen ion and electronic conduction was investigated in detail. Results showed that the fuel mixture significantly affected the area-specific resistance of the BSCF cathode materials, by controlling the oxygen deficiency and stabilizing the Co2+ oxidation state. It was demonstrated that high fuel-to-metal cations molar ratios and high reducing power of the combustion fuel mixture are mainly responsible for the decreasing of the area-specific resistance o…
High performance p-type segmented leg of misfit-layered cobaltite and half-Heusler alloy
2015
In this study, a segmented p-type leg of doped misfit-layered cobaltite Ca_(2.8)Lu_(0.15)Ag_(0.05)Co_4O_(9+δ) and half-Heusler Ti_(0.3)Zr_(0.35)Hf_(0.35)CoSb_(0.8)Sn_(0.2) alloy was fabricated and characterized. The thermoelectric properties of single components, segmented leg, and the electrical contact resistance of the joint part were measured as a function of temperature. The output power generation characteristics of segmented legs were characterized in air under various temperature gradients, ΔT, with the hot side temperature up to 1153 K. At ΔT ≈ 756 K, the maximum conversion efficiency reached a value of ∼5%, which is about 65% of that expected from the materials without parasitic l…
Ab initio thermodynamic study of (Ba,Sr)(Co,Fe)O3 perovskite solid solutions for fuel cell applications
2013
(Ba,Sr)(Co,Fe)O3 (BSCF) perovskite solid solutions are promising materials for solid oxide fuel cell cathodes and oxygen permeation membranes. Cathode performance strongly depends on the morphology of these materials remaining as a single phase or two-phase mixture. Combining ab initio calculations of the atomic and electronic structure of different supercells with thermodynamics of solid solutions, we have constructed and discussed phase diagrams of several important BSCF chemical compositions. It is demonstrated that in BSC cobaltite solid solution the spinodal decomposition may occur already at relatively low temperatures, while ferrite (BSF and SCF) solid solutions decompose at relative…
Solid-state compatibility of Ca:LaNbO4 with perovskite cathodes: Evidences from X-ray microspectroscopy
2022
The solid-state compatibility between calcium-doped lanthanum niobate and three perovskite cathode materials was investigated using two X-ray microbeam techniques, micro X-ray fluorescence and micro X-ray absorption spectroscopy. The cathode powders (lanthanum strontium ferrite, either cobalt or copper-doped, and lanthanum strontium cobaltite) in contact with the dense electrolyte pellet were annealed at 1150 degrees C for 12-144 h to simulate the effect of thermal stresses due to fabrication and long-term operation. As a result, several interdiffusion phenomena were then observed on the bilayer cross-sections: in particular, the chemical state and coordination environment of calcium, iron,…