Search results for "Composite material"
showing 10 items of 2340 documents
Fracture of a Brittle Membrane
1997
A unique microstructure of the fiber networks deposited from foam-fiber suspensions
2015
Abstract Fiber networks can be formed using aqueous foam as the suspending medium. The mean bubble size of the foam affects the resulting pore-size distribution of the fiber network. The foam–fiber interactions cause in particular an increase in the proportion of large micropores of the network, in comparison with the fiber networks that result from traditional water forming at a similar material density. Experiments were carried out for two different types of cellulose fiber, and characterization of the resulting pore structure was based on X-ray microtomography of the resulting fiber networks. The unique pore structure obtained with foam forming was reflected in various macroscopic proper…
Ultrasonication as a Method of Investigation of the Mechanical Properties of Doped Hafnium Barium Titanate
2012
The purpose of this study was to fabricate dense ceramic specimens from the system of BaTiO3-BaHfO3 and then to perform mechanical tests. The effect of Hf content on a microstructure and mechanical properties of the BaTiO3-BaHfO3 solid solution was investigated at room temperature. To determine the elastic constants (the Young′s modulus E, the shear modulus G, bulk modulus K and the Poisson′s ratio v) of BaHfxTi1-xO3 a method of measurement of the longitudinal (VL ) and transverse (VT ) ultrasonic wave velocities for this type of material was developed.
Effect of two novel bio-based rejuvenators on the performance of 50% RAP mixes - a statistical study on the complex modulus of asphalt binders and as…
2019
An experimental study was conducted to evaluate the effectiveness of two bio-additives as rejuvenators on the properties of asphalt mixtures containing 50% RAP and their binder constituents containing 37% RAP binder. Before mixing, the rejuvenators were blended with fresh bitumen and the extracted and recovered RAP bitumen, and changes in the rheological properties of the binders were assessed using performance grading (PG) criteria. The results showed that both rejuvenators could improve the low-temperature performance of the aged RAP binder and restore its low-temperature properties. Master curves for the unaged, RTFO-aged, and PAV aged blends were constructed using both the Christensen-A…
Tensile behaviour of anti-symmetric CFRP composite
2011
Abstract This paper addresses the response of a 17-ply anti-symmetric carbon/epoxy composite subjected to uniaxial tensile loading. Hashin ply damage model is adopted to describe the damage behaviour of the plies, whereas damage initiation and progression of the interfaces are characterised by mixed-mode cohesive damage model. Force-displacement curves obtained numerically and experimentally show good agreement. Results show that all laminae and interfaces experience the damage except laminae with 0o fibre. In addition, damage is concentrated at the tab and central regions of the tensile specimen. Edge delamination is observed in all interfaces.
Stress Transfer within CNT Fibres: A FEA Approach
2015
Abstract Carbon nanotube (CNT) fibres are characterized by extreme anisotropy in their structure and physical properties. These fibres have been shown to have high axial strength, but poor shear strength between carbon nanotubes; for this reason it is difficult to transfer stress uniformly acrossthe fibre cross section. Here, Finite Element Analysis (FEA) is used to predict the stress distribution and the stress-strain curves of CNT fibres. The resultsdemonstrate that, in accordance with St. Venant principle,very considerable length-to-diameter ratios (> 10 3 ) are required to obtain a uniform stress distribution within the fibres even in the presence of low applied strain.
Reliability of numerical models for simulating galvanic corrosion processes
2012
International audience; Maturity of numerical simulation represents an important issue in the development of predictive models of galvanic corrosion. As widely used in electrochemical engineering, a coupled electrochemical-transport-reaction (CETR) model is recommended to simulate the current distribution above a galvanic corrosion cell made of the cut-edge of a galvanized steel sheet. Nevertheless, simulating current density distributions obtained experimentally by scanning vibrating electrode technique (SVET) above such a galvanic cell appears to be more accurate using an electrostatic model considering a homogeneous conductivity. In this case, the absence of concentration gradients next …
Reactivity of gypsum faces according to the relative humidity by scanning force microscopy
1997
Abstract This article reports the experimental observation of the stability of the different faces of calcium sulphate dihydrate (gypsum CaSO 4 .2H 2 O) according to the relative humidity. Scanning Force Microscopy experiments were carried out with a view to discerning the topography of the surfaces, the chemical compositional domains, and in an attempt to evaluate the friction and viscoelastic properties of the surface. Our results indicate that the (010) face of gypsum is hydrophilic and very reactive contrary to the less hydrophilic (120) and (101) faces which remain stable depending on the relative humidity. It is clear from our results that a precipitation like process can be induced b…
Flexible minerals: self-assembled calcite spicules with extreme bending strength.
2013
Flexi-Fibers Glass or metal fibers can show incredible flexibility. Natalio et al. (p. 1298 ; see the Perspective by Sethmann ) used the protein silicatein-α, which is responsible for the biomineralization of silicates in sponges, to guide the formation of spicules made of calcite. These synthetic spicules could be bent to a high degree because of their inherent elasticity, whilst retaining the ability to guide light.
Rheological and Mechanical Behavior of LDPE/Calcium Carbonate Nanocomposites and Microcomposites
2012
The increase of the interest in polymer nanocomposites has been leading to continuous growing search toward nanofillers alternative to the widely known clay-based ones. One of these possible alternatives is represented by calcium carbonate nanoparticles, which have not been widely investigated in such context. In this article, a study on the rheological and morphological behavior of dif- ferent low density polyethylene-calcium carbonate nanocomposites, compared with a reference calcium carbonate microcomposite, is presented. Several different nanosized calcium carbonates at different amounts were used. The results from the rheological and me- chanical tests outlined that only minor changes …