Search results for "Compressive Strength"
showing 10 items of 111 documents
In vitro evaluation of biomimetic chitosan-calcium phosphate scaffolds with potential application in bone tissue engineering.
2013
This work reports on the physicochemical properties and in vitro cytotoxicity assessment of chitosan–calcium phosphate (Cs–CP) scaffolds for bone tissue engineering, which were synthesized by a novel biomimetic co-precipitation method. X-ray diffraction (XRD) along with scanning electron microscopy (SEM) analysis confirmed the porous morphology of the scaffolds and the amorphous nature of the inorganic phase with different crystallite sizes and the formation of various forms of calcium phosphate. Compressive mechanical testing revealed that the Young’s modulus of the biomaterials is in the range of human trabecular bone. In vitro tests were performed on the biomaterials for up to 14 days to…
Does phosphorus affect the industrial Portland cement reactivity?
2018
Abstract The effect of phosphorous on the mineralogy and reactivity of Portland cement has been investigated through an industrial clinkers series. The samples were collected from the same Tunisian cement plant and classified according to the content of P2O5 from 0.5% to 1.1%. All samples were manufactured at the same thermal and cooling conditions as well as possible. The specimens were characterized by X-ray fluorescence spectrometry and optical microscopy techniques and their mineralogy was determined by X-ray powder diffraction coupled to the Rietveld analysis. The cements reactivity prepared from the clinkers was followed by means of isothermalcalorimetry. The compressive strength of t…
Pumice powder as filler of self-compacting concrete
2015
Abstract An experimental study on the rheological and mechanical properties of self-compacting concrete with pumice powder used as filler additive is presented. Self-compacting concrete (SCC) shows its peculiar characteristics in the fresh state and many researches have been developed with reference to its rheological characteristics paying attention to the techniques of self-compacting properties assessment. One of the most important aspect in concrete mix-design is the type and the amount of fillers with respect to water and cement: this amount has great influence not only on self-compacting properties (fluidity, segregation, etc.), but also on the mechanical properties of the mixture. Vo…
Development of a performance threshold approach for identifying the management options for stabilisation/solidification of lead polluted soils
2014
Two soils spiked with lead at different rates were stabilised/solidified using Portland cement and fy ash at different soil:binder ratios, and tested for their setting time, unconfined compressive strength, leachability and durability. A performance threshold approach was used in order to identify optimal management options for the products of the S/S treatment. Results show that soil texture, percentage of binders and lead concentration play an important part in the treatment, significantly influencing the performance of the resulting products in terms of curing, compressive strength and durability. Pb soil concentrations higher than 15000 mg kg-1 were found to heavily reduce the applicab…
Are there any differences in various polyaxial locking systems? A mechanical study of different locking screws in multidirectional angular stable dis…
2012
Numerous angular stable plates for the distal radius exist, and technically based comparisons of the polyaxial locking interfaces are lacking. The aim of this mechanical study was to investigate three different locking interfaces of angular stable volar plates by cantilever bending: VA-LCP Two-Column Distal Radius Plates 2.4 mm (Synthes® GmbH, Oberdorf, Switzerland), IXOS® P4 (Martin, Tuttlingen, Germany) and VariAX™ (Stryker®, Duisburg, Germany). We assessed the strength of 0°, 5°, 10° and 15° screw locking angles and tested the bending strength from 10° to 5° angles by cyclic loading until breakage. The final setup repeated the above assessments by inclusion of four locking screws. The si…
Suitability of Illite Based Clays of Latvia for Chemical and Thermal Activation
2014
Materials has been synthesized in the temperature range from 600-800 0C from illite based clays of Latvia under activation of KOH and NaOH solutions (4-6 M). Compressive strength and apparent porosity were measured. The effect of the concentration of KOH and NaOH solutions on the material mechanical properties was investigated by means of infrared spectroscopy (IR). Compressive strength data of the materials showed that via such activation building materials with good quality can be obtained.
The effect of through-thickness compressive stress on mode II interlaminar fracture toughness
2017
Abstract The effect of through-thickness compressive stress on mode II interlaminar fracture toughness is investigated experimentally and replicated numerically. The modified Transverse Crack Tensile specimen recently proposed by the authors is used, together with an experimental device designed to apply a constant transverse compressive stress on the surface of the specimen. Experiments are conducted using IM7/8552 specimens for different compressive stresses, ranging from 0 to 100 MPa, covering all the practical applications commonly encountered in the aeronautical industry (e.g., tightened filled holes or bolted joints). It is shown that mode II interlaminar fracture toughness increases …
Masonry Compressive Strength Prediction Using Artificial Neural Networks
2019
The masonry is not only included among the oldest building materials, but it is also the most widely used material due to its simple construction and low cost compared to the other modern building materials. Nevertheless, there is not yet a robust quantitative method, available in the literature, which can reliably predict its strength, based on the geometrical and mechanical characteristics of its components. This limitation is due to the highly nonlinear relation between the compressive strength of masonry and the geometrical and mechanical properties of the components of the masonry. In this paper, the application of artificial neural networks for predicting the compressive strength of m…
Behavior in compression of concrete cylinders externally wrapped with basalt fibers
2015
Abstract This paper gives additional information on the use of new class of composites constituted by Basalt Fiber Reinforced Polymer (BFRP) bonded with epoxy resin to concrete specimens as an alternative confinement material for compressed concrete members with respect to carbon or glass fibers. From the experimental point of view, concrete cylinders are wrapped with continuous fibers, in the form of sheets, applying both full and partial discrete wrapping with BFRP straps, and then tested in compression. For comparison, few other concrete cylinders are wrapped with Carbon Fiber Reinforced Polymer (CFRP) sheets and tested in compression. The number and type of plies (full or partial wrappi…
Antibacterial, physical and mechanical properties of bonding agent containing synthesized Zinc Dimethacrylate
2019
Background The aim of this study includes synthesis of zinc dimethacrylate ionomer (ZDMA) by a new method, incorporate it into resin bonding and evaluate its antibacterial, physical and mechanical properties. Material and methods Resin adhesives containing 0 to 5% wt of ZDMA was produced and the following tests were accomplished: A: Antibacterial test: 1.Direct contact test. 2.Material aging; in both of them the bacterial colony counting were performed. B: Physical test: 1.Degree of conversion (D.C). 2.Evaluating the amount of released Zinc ion release in aqueous medium. C: Mechanical test: 1.Compressive strength test. 2.Shear bond test (enamel and dentine separately). The obtained results …