Search results for "Computer Science Applications"
showing 10 items of 3993 documents
Distribution of relaxation times in 0.5PMN-0.5PSN ceramics
2007
Dielectric properties of chemically ordered and disordered 0.5PbMg1/3Nb2/3O3-0.5 PbSc1/2Nb1/2O3 (0.5PMN-0.5PSN) ceramics were investigated in frequency range from 20 Hz to 3 GHz by dielectric spectroscopy. The broad dielectric dispersion, similar to this typically obtained for relaxor ferroelectrics (RFE), was observed in both ceramics below 350 K. The frequency dependence of dielectric permittivity of these ceramics were analyzed in terms of the distribution of relaxation times and showed the splitting into two components at lower temperatures. The longest relaxation times part slows down following Vogel-Fulcher law with lower freezing temperature compare with typical RFE like PbMg1/3Nb2/3…
Magnetization relaxation in YBCO films with improved supercurrent transport properties
2010
The relaxation of the irreversible magnetization in optimally doped YBCO films with natural and artificial pinning centres was measured in zero-field cooling conditions using SQUID magnetometry. The external magnetic field H was oriented along the c axis. An appropriate method for the determination of the characteristic vortex pinning energy from the normalized vortex-creep activation energy is discussed. This is based on the existence of a crossover elastic (collective) vortex creep at low temperatures T – plastic vortex creep at high T, caused by the T dependent macroscopic currents induced in the sample during magnetization measurements.
Influence of the boundary conditions on heat and mass transfer in spacer-filled channels
2017
The purpose of this study is to discuss some problems which arise in heat or mass transfer in complex channels, with special reference to the spacer-filled channels adopted in membrane processes. Among the issues addressed are the consistent definition of local and mean heat or mass transfer coefficients; the influence of the wall boundary conditions; the influence of one-side versus two-side heat/mass transfer. Most of the results discussed were obtained by finite volume CFD simulations concerning heat transfer in Membrane Distillation or mass transfer in Electrodialysis and Reverse Electrodialysis, but many of the conclusions apply also to different processes involving geometrically compl…
Time-Resolved Luminescence of Nanocrystalline Inorganic Complex Oxides
2007
Two types of complex nanosized oxides – cerium doped Y3Al5O12 (YAG) and CaWO4– have been studied by means of time-resolved luminescence spectroscopy. Comparative study of time-resolve luminescence characteristics of cerium doped YAG single crystal, nanopowders and nanoceramic as well as for CaWO4 macro- and nanocrystals has been done. Two components in the decay kinetic of Ce3+ related emission in YAG nanocrystals were detected and it was suggested that a different energy transfer rate to volume and surface Ce3+ ions takes place. It is shown that the segregation of Ce3+ ions near nanoparticles surface and/or dislocation lines plays a crucial role in degradation of light yield of cerium rela…
Nano composite membrane-electrode assembly formation for fuel cell-modeling aspects
2007
Long term stability is an essential requirement for fuel cell applications in automobile and stationary energy systems. In these systems the agglomeration of the catalyst nanoparticles is a well-known phenomenon which cannot be easily overcome or compensated for by re-designing the system. A direct result of this occurrence is the irreversible decrease of the electrochemical performance. Irregularities in electric field distribution are one root cause for migration and subsequent agglomeration of the catalyst nanoparticle. In this work, the impact of the electrode mechanical deformation on electric field distribution was studied using a computer modeling approach. Model of a Proton Exchange…
Microfabrication of hybrid fluid membrane for microengines
2015
International audience; This paper describes the microfabrication and dynamic characterization of thick membranes providing a technological solution for microengines. The studied membranes are called hybrid fluid-membrane (HFM) and consist of two thin membranes that encapsulate an incompressible fluid. This work details the microelectromechanical system (MEMS) scalable fabrication and characterization of HFMs. The membranes are composite structures based on Silicon spiral springs embedded in a polymer (RTV silicone). The anodic bonding of multiple stacks of Si/glass structures, the fluid filling and the sealing have been demonstrated. Various HFMs were successfully fabricated and their dyna…
Normal metal - insulator - superconductor thermometers and coolers with titanium-gold bilayer as the normal metal
2018
We have fabricated superconductor - insulator - normal metal - insulator - superconductor (SINIS) tunnel junctions in which Al acts as the superconductor, AlOx is the insulator, and the normal metal consists of a thin Ti layer (5 nm) covered with a thicker Au layer (40 nm). We have characterized the junctions by measuring their current-voltage curves between 60 mK and 750 mK. For comparison, the same measurements have been performed for a SINIS junction pair whose normal metal is Cu. The Ti-Au bilayer decreases the SINIS tunneling resistance by an order of magnitude compared to junctions where Cu is used as normal metal, made with the same oxidation parameters. The Ti-Au devices are much mo…
Riga Group’s recent results on laser applications for skin diagnostics
2021
Abstract The laser-related activities are reviewed of the Biophotonics Laboratory at UL Institute of Atomic Physics and Spectroscopy following the previous ICSQE-2018 conference. Four recent research projects are considered, including one EC Horizon-2020 project, two European Regional Development Fund (ERDF) projects and one project funded by the Latvian Council of Science (LCS). The projects are generally aimed at developing new optical methods and technologies for non-invasive in-vivo skin assessment to facilitate the early diagnostics of skin malformations (including cancers). Most of the projects explore novel approaches of camera-based biomedical imaging to the clinical diagnostics and…
Effect of the milling conditions on the degree of amorphization of selenium by milling in a planetary ball mill
2007
The effect of the milling parameters (rotation speed of the milling device and duration of milling) on the phase composition of the products of milling of fully crystalline selenium has been investigated. The milling was conducted using a planetary micromill and the phase composition of the milling products was determined by differential thermal analysis. It has been found that ball milling leads to the partial amorphization of the starting crystalline material. The content of amorphous phase in the milling products depends, in a rather complicated way, on the milling parameters. At the milling parameters adopted in the present study, the milling product was never fully amorphous. The compl…
Film-substrate lattice-engineering of HTS thin films
2008
Materials may show anisotropic properties on different crystal directions and this is also the case of High Temperature Superconductors (HTS). To take advantage of the materials anisotropy one concept of interest is 'orientation engineering' in thin films. This can be realized through the control of the film-substrate lattice relationship. Some examples in this regard are presented in this work and through comparative analysis we try to evaluate the viability of this approach and of he entcountered problems. It is expected that in the future this approach will generate new nano composite materials with new properties and effects leading to development of new devices with new or improved fun…