Search results for "Computer Science Applications"
showing 10 items of 3993 documents
Using a neural network for predicting the average grain size in friction stir welding processes
2009
In the paper the microstructural phenomena in terms of average grain size occurring in friction stir welding (FSW) processes are focused. A neural network was linked to a finite element model (FEM) of the process to predict the average grain size values. The utilized net was trained starting from experimental data and numerical results of butt joints and then tested on further butt, lap and T-joints. The obtained results show the capability of the AI technique in conjunction with the FE tool to predict the final microstructure in the FSW joints.
Oil whip-induced wear in journal bearings
2014
Published version of an article in the journal: International Journal of Advanced Manufacturing Technology. Also available from the publisher at: http://dx.doi.org/10.1007/s00170-014-5805-8 This paper investigates the effect of oil whirl and oil whip in fluid film radial bearings due to possible metallic contact. The degree of metallic contact and thereby wear and tear between rotating shafts and bearing bushes is assessed by measuring electric currents through the oil film. The current as well as the voltage varied in accordance with the contact ratio between the shaft and bush in the fluid film radial bearing. The gauge signal thus indicates the degree of metallic contact based on the thi…
Reconstitution of a protein monolayer on thiolates functionalized gaas surface
2012
International audience; In the aim to realize an efficient resonant biosensor, gallium arsenide (GaAs) presents many advantages. In addition to its properties of transduction, GaAs is a crystal for which microfabrication processes were developed, conferring the possibility to miniaturize the device and integrate electronic circuit. Moreover, the biofunctionalization could be realized on the crystalline surface without layer deposition, constituting a real advantage to perform reusable sensor. The functionalization of GaAs surface was engaged in order to immobilize a protein monolayer on this substrate. Functionalization was done using a mixed self assembled monolayer of thiolate molecules. …
Comparison of the friction and wear properties of titanium and oxidised titanium in dry sliding against sintered high speed steel HS18-0-1 and agains…
2005
Abstract The paper presents the results of conformal pin-on-disc tribological tests concerning the hard oxidised zone, α-Ti(O), created at the surface of a titanium specimens sliding against the sintered and hardened up to 850 HV30, Grade T1 high speed steel (HS18-0-1) counterspecimens. Comparison with the results obtained for the tests performed against hardened up to 620 HV30 C45 carbon steel counterspecimens has been done. Testing was carried out at room temperature and at unlubricated conditions. After tests the structures and compositions of the worn surfaces and wear debris were a subject of LOM, SEM observations and X-ray microanalyses. In comparison with the baseline—the Ti/T1 HSS c…
The role of coatings in controlling the cutting process when turning with coated indexable inserts
1998
Abstract This paper is concerned with the variations in the specific cutting pressure and the tool–chip interface temperature that occur when machining a medium carbon steel and an austenitic stainless steel with TiC-, TiC/TiN- and TiC/Al2O3/TiN- coated inserts. Extensive experimental studies involving the cutting force and the interface temperature were performed. A standard thermocouple embedded in the workpiece was used to determine the cutting temperature. Two new parameters were introduced in order to compare both the mechanical and thermal loadings of the tool–chip contact for coated flat-faced and grooved inserts. Some optimal coating structures for high speed machining of these stee…
Friction and wear properties of titanium and oxidised titanium in dry sliding against hardened C45 steel
2004
Abstract The aim of the paper is to present the results of conformal pin-on-disc tribological tests concerning the hard oxidised zone created in superficial layer of a titanium specimen sliding against the hardened to a hardness of 690 HV carbon C45 steel counterspecimen. Tribological testing was carried out at room temperature and at unlubricated conditions. After tests the structures and chemical compositions of the wear debris and worn surfaces were a subject of SEM and X-ray investigations. In comparison with the baseline the technical quality titanium/C45 steel couple, the wear and lifetime performance of the oxidised titanium/steel C45couple was markedly superior. Dominant wear debris…
A three-dimensional cohesive-frictional grain-boundary micromechanical model for intergranular degradation and failure in polycrystalline materials
2013
Abstract In this study, a novel three-dimensional micro-mechanical crystal-level model for the analysis of intergranular degradation and failure in polycrystalline materials is presented. The polycrystalline microstructures are generated as Voronoi tessellations, that are able to retain the main statistical features of polycrystalline aggregates. The formulation is based on a grain-boundary integral representation of the elastic problem for the aggregate crystals, that are modeled as three-dimensional anisotropic elastic domains with random orientation in the three-dimensional space. The boundary integral representation involves only intergranular variables, namely interface displacement di…
A local chemical potential approach within the variable charge method formalism
2008
A new and computationally efficient implementation of the variable charge method of Streitz and Mintmire (1994 Phys. Rev. B 50 11996) is presented. In particular a local chemical potential approach that optimizes the charge on only those atoms expected to be ionic is developed. By doing so, the charge fluctuation problem experienced in regions far from any oxygen is solved, leading to a linear minimization problem of the electrostatic energy. In the dilute oxygen limit, such an approach can lead to at least an order of magnitude saving in computation.
Diagnostic Performance and Radiation Dose of the EOS System to Image Enchondromatosis: A Phantom Study
2020
Background: Radiation doses and capability of EOS, conventional radiography (CR), and computed tomography (CT) to detect and measure enchondromas in a dedicated five-year-old anthropomorphic phantom were compared. Methods: To simulate enchondromas, minced pieces of chicken bone and cartilage were packed in conventional kitchen plastic foil to create ovoidal/rounded masses and randomly hung on the phantom. The phantom was imaged five times with CR, CT, and EOS, each time changing the number and position of inserts. All images were reviewed by a senior radiologist and a radiology resident. Results: EOS and CR detected all inserts in 4/5 cases (80%), while in one case 1/17 inserts was not seen…
Modelling of Pe C alloys solidification using the artificial heat source method
1997
Abstract In the paper the numerical solutions concerning the cast iron and also the carbon steel solidification are presented. In order to take into account the non-linearities appearing in differential equations describing the boundary-initial problem considered — a certain algorithm called the artificial heat source method has been used. The examples illustrating the possibilities of proposed method applications have been solved by means of the boundary element method, but the others numerical methods can be also utilized.