Search results for "Computer-aided design"

A distributed genetic algorithm for restoration of vertical line scratches

2008

This paper reports a distributed algorithm for the restoration of still frames corrupted by vertical line scratches. The restoration is here approached as an optimisation problem, and is solved using an ad-hoc Genetic Algorithm. The distributed algorithm is designed following a pipeline logical structure. The front end is a network of standard workstations with heterogeneous operating systems. The quality of image is appreciable and the computational time is quite low with respect the sequential version.

A solution process for simulation-based multiobjective design optimization with an application in the paper industry

2014

In this paper, we address some computational challenges arising in complex simulation-based design optimization problems. High computational cost, black-box formulation and stochasticity are some of the challenges related to optimization of design problems involving the simulation of complex mathematical models. Solving becomes even more challenging in case of multiple conflicting objectives that must be optimized simultaneously. In such cases, application of multiobjective optimization methods is necessary in order to gain an understanding of which design offers the best possible trade-off. We apply a three-stage solution process to meet the challenges mentioned above. As our case study, w…

Introduction to molecular topology: basic concepts and application to drug design.

2012

In this review it is dealt the use of molecular topology (MT) in the selection and design of new drugs. After an introduction of the actual methods used for drug design, the basic concepts of MT are defined, including examples of calculation of topological indices, which are numerical descriptors of molecular structures. The goal is making this calculation familiar to the potential students and allowing a straightforward comprehension of the topic. Finally, the achievements obtained in this field are detailed, so that the reader can figure out the great interest of this approach.

Twofold coordinated Ge defects induced by gamma-ray irradiation in Ge-doped SiO2

2008

We report an experimental study by photoluminescence, optical absorption and Electron Paramagnetic Resonance measurements on the effects of exposure of Ge-doped amorphous SiO2 to gamma ray radiation at room temperature. We have evidenced that irradiation at doses of the order of 1 MGy is able to generate Ge-related defects, recognizable from their optical properties as twofold coordinated Ge centers. Until now, such centers, responsible for photosensitivity of Ge-doped SiO2, have been induced only in synthesis procedures of materials. The found result evidences a role played by gamma radiation in generating photosensitive defects and could furnish a novel basis for photosensitive pattern wr…

The FiR 1 photon beam model adjustment according to in-air spectrum measurements with the Mg(Ar) ionization chamber.

2014

Abstract The mixed neutron–photon beam of FiR 1 reactor is used for boron–neutron capture therapy (BNCT) in Finland. A beam model has been defined for patient treatment planning and dosimetric calculations. The neutron beam model has been validated with an activation foil measurements. The photon beam model has not been thoroughly validated against measurements, due to the fact that the beam photon dose rate is low, at most only 2% of the total weighted patient dose at FiR 1. However, improvement of the photon dose detection accuracy is worthwhile, since the beam photon dose is of concern in the beam dosimetry. In this study, we have performed ionization chamber measurements with multiple b…

Filtered circular fingerprints improve either prediction or runtime performance while retaining interpretability

2016

Harmonic solution of semiconductor transport equations for microwave and millimetre-wave device modelling

2004

The transport equations for charges in a semiconductor have been solved for a periodic voltage excitation by means of a harmonic approach, for modelling of microwave and millimetre-wave active devices. The solution is based on the expansion of the unknown physical quantities in Fourier series in the time domain, and on the discretisation in the space domain. A Waveform-Balance technique in the time domain is used to solve the resulting non-linear equations system. In this way the time step is determined only by Nyquist's sampling requirements at the operating frequency, irrespective of the relaxation times of the semiconductor. This approach allows for a longer time step, and therefore a sh…

High-visibility interference fringes with femtosecond laser radiation.

2009

We propose and experimentally demonstrate an interferometer for femtosecond pulses with spectral bandwidth about 100 nm. The scheme is based on a Michelson interferometer with a dispersion compensating module. A diffractive lens serves the purpose of equalizing the optical-path-length difference for a wide range of frequencies. In this way, it is possible to register high-contrast interference fringes with micrometric resolution over the whole area of a commercial CCD sensor for broadband femtosecond pulses.

Mean-Field Game Modeling the Bandwagon Effect with Activation Costs

2015

This paper provides a mean-field game theoretic model of the bandwagon effect in social networks. This effect can be observed whenever individuals tend to align their own opinions to a mainstream opinion. The contribution is threefold. First, we describe the opinion propagation as a mean-field game with local interactions. Second, we establish mean-field equilibrium strategies in the case where the mainstream opinion is constant. Such strategies are shown to have a threshold structure. Third, we extend the use of threshold strategies to the case of time-varying mainstream opinion and study the evolution of the macroscopic system.

Novel algorithms for 3D surface point cloud boundary detection and edge reconstruction

2019

Abstract Tessellated surfaces generated from point clouds typically show inaccurate and jagged boundaries. This can lead to tolerance errors and problems such as machine judder if the model is used for ongoing manufacturing applications. This paper introduces a novel boundary point detection algorithm and spatial FFT-based filtering approach, which together allow for direct generation of low noise tessellated surfaces from point cloud data, which are not based on pre-defined threshold values. Existing detection techniques are optimized to detect points belonging to sharp edges and creases. The new algorithm is targeted at the detection of boundary points and it is able to do this better tha…