Search results for "Converter"
showing 10 items of 275 documents
Design and simulation of efficient combinational circuits based on a new XOR structure in QCA technology
2021
AbstractQuantum-dot cellular automata (QCA), due to its unique characteristics like low power consumption, nanoscale design, and high computing speed is considered as an emerging technology, and it can be used as an alternative for CMOS technology in circuit design for quantum computers in the near future. XOR gate has many applications in the design of digital circuits in QCA. In this paper, an efficient novel structure of XOR gate is proposed in QCA. Also, a novel 1-bit comparator circuit, 1-bit full adder, binary to gray and gray to binary convertor code based on the proposed XOR is designed and simulated using QCADesigner 2.0.3. The simulation results demonstrated that the proposed stru…
Design and Realization of a Bidirectional Full Bridge Converter with Improved Modulation Strategies
2020
In this paper a Full-Bridge Converter (FBC) for bidirectional power transfer is presented. The proposed FBC is an isolated DC-DC bidirectional converter, connected to a double voltage source&mdash
Benefits and Drawbacks of A High Frequency Gan Zvzcps Converter
2017
This paper presents the benefits and drawbacks of replacing the traditional Si Mosfets transistors with enhancement mode GaN transistors in a Half-Bridge Zero Voltage and Zero Current Switching Power Switching (ZVZCPS) converter. This type of converters is usually used as Electronic Power Converters (EPC) for telecommunication satellites travelling-wave tube amplifiers (TWTAs). In this study, firstly the converter is theoretically analysed, obtaining its operation, losses and efficiency equations. From these equations, optimizations maps based on the main system parameters are obtained. These optimization maps are the key to quantify the potential benefits of GaN transistors in this type of…
Output Impedance Improvement Using Coupled Inductors
2017
When using a single DC/DC converter with multiple outputs and having a buck topology, which has one filter inductor per output, the designer can choose to couple these outputs together. This paper demonstrates additional benefits of coupling output inductors together. Apart from saving mass and volume, and due to an improved small signal behaviour it also reduces the output impedance of the regulated output. The paper will analyse a seven output push-pull converter used as a space power converter module and verify the theoretical results with experimental measurements.
Min-Type Control Strategy of a DC-DC Synchronous Boost Converter
2019
International audience; This paper presents the analysis and design of a min-type strategy to control a synchronous boost converter in continuous conduction mode. The strategy uses a nonlinear switching surface to establish the change of topology in the converter and is analyzed by means of a sliding-mode control approach. Subsequently, the min-type strategy is modified by a hybrid control formulation, which introduces a hysteresis width and a dwell-time to obtain a finite switching frequency in the start-up and steady-state respectively. The hybrid control formulation is implemented digitally by means of a microprocessor which processes the samples of inductor current and capacitor voltage…
Design and realization of a DC/DC converter with a partially saturated inductor
2017
DC/DC converters, in some types of applications such as portable equipments, can require more space than it is actually available. The inductor is typically the most bulky element and the possibility to reduce its size can save up to 50% of the converter volume and area [1][2], thus increasing the power density. This reduction, however, comes with nonlinear effects caused by the saturation of the ferromagnetic core. An appropriate modelling of the inductor and of the converter circuit is needed for guaranteeing a good output power quality (Fig. 1). A Boost converter with an inductor in the partially saturated roll-off operating zone was designed and realized to study the behaviour of DC/DC …
Design and Performance Evaluation of a High Power-Density EMI Filter for PWM Inverter-Fed Induction-Motor Drives
2016
This paper presents the design of an electromagnetic interference (EMI) filter for a low-voltage high-current induction-motor drives supplied by dc power grids. In order to effectively design the EMI filter, a suitable common-mode/differential-mode (CM/DM) separation technique has been used. Due to the high operating currents, the software-based separation technique using time-domain measurements has been applied. The proposed technique allows the CM and DM sections of the EMI filter to be properly selected in a more economical way, i.e., without the need of a dedicated hardware or costly radio frequency (RF) instrumentation. The design has been done according to a power-density criterion. …
Calibration of the underground muon detector of the Pierre Auger Observatory
2021
To obtain direct measurements of the muon content of extensive air showers with energy above $10^{16.5}$ eV, the Pierre Auger Observatory is currently being equipped with an underground muon detector (UMD), consisting of 219 10 $\mathrm{m^2}$-modules, each segmented into 64 scintillators coupled to silicon photomultipliers (SiPMs). Direct access to the shower muon content allows for the study of both of the composition of primary cosmic rays and of high-energy hadronic interactions in the forward direction. As the muon density can vary between tens of muons per m$^2$ close to the intersection of the shower axis with the ground to much less than one per m$^2$ when far away, the necessary bro…
DC-DC Converter for Photovoltaic Application with MPPT function embedded interleaved 4
2012
We present a DC-DC converter for photovoltaic (PV) applications that is suitable for a distributed power conversion approach, obtained by transferring part of the electronics from the inverter to the module. The proposed circuit is a high-efficiency four-phase interleaved boost converter employing relatively low-valued inductive and capacitive components. Its realization is made possible thanks to the design of a dedicated integrated circuit (IC) performing the converter control section as well as the Maximum Power Point Tracking (MPPT) algorithm. The solution is designed for a maximum delivered power of 300 W and to work with MPPT voltage between 9 V and 40 V, with maximum allowed panel cu…
Development of bidirectional dc-dc converters for hybrid power sources - Final Report
2018
A Bidirectional Isolated Full-Bridge Converter was designed, prototyped and tested. The device is intended to interface a Bank of Supercapacitors with a battery-powered bus, in order to boost the capability of supplying large power peaks. The converter was based on the Isolated Dual Active Bridge configuration. When driven by an external control voltage, it is capable of generating in both directions a train of current pulses, with 2kW peak power, for any battery voltage in the range 24-32V and for any supercapacitor voltage in the range 35-70V. Worst-case battery current was 70A. Pulse duration was 100ms with 50% duty cycle and 1 ms rise time.