Search results for "Converters"

Nonlinear Modeling of DC/DC Converters Using the Hammerstein's Approach

2007

This paper deals with the modelling of highly nonlinear switching power-electronics converters using black-box identification methods. The duty cycle and the output voltage are chosen, respectively, as the input and the output of the model. A nonlinear Hammerstein-type mathematical model, consisting of a static nonlinearity and a linear time-invariant model, is considered in order to cope with the well-known limitations of the more common small-signal models, i.e. the entity of the variations of the variables around a well-defined steady-state operating point and the incorrect reproduction of the steady-state behavior corresponding to input step variations from the above steady-state operat…

Automatic EMI filter design for power electronic converters oriented to high power density

2018

In this paper, a complete computer aided procedure based on the power density concept and aimed at the automatic design of EMI filters for power electronic converters is presented. It is rule-based, and it uses suitable databases built-up by considering information on passive components available from commercial datasheets. The power density constraint is taken into consideration by imposing the minimization of the filter volume and/or weight; nevertheless, the system in which the automatically designed filter is included satisfies the electromagnetic compatibility standards limits. Experimental validations of the proposed procedure are presented for two real case studies, for which the per…

Design of EMI Filters Using Multi-Objective Optimization

2018

A multi-objective design procedure for EMI filters in power converters is proposed. In a first step, the results obtained by an automatic design of EMI filters for power electronic converters oriented to satisfy the electromagnetic compatibility standards and the power density constraint which impose the minimization of the filter volume and/or weight, are evaluated. In a second step, the power losses and the cost related to the EMI filter configurations are estimated. By using the dominance concept, the EMI filter designs which are part of the Pareto front are selected among a discrete set of feasible configurations. Therefore, the configurations of the Pareto front take into consideration…

Overview and performance comparison of grid synchronization algorithms

2014

Distributed power generation units are experiencing an impressive growth. Consequently, the amount of energy injected by non-linear loads as power converters is expected to increase. Stability and quality of the overall grid are heavily affected by performances of grid-side converters. In this paper, an overview of grid-synchronization technique is proposed. The grid-side inverter is implemented in MATLAB/Simulink® environment including current control and grid-synchronization section. Both Synchronous Reference Frame (SRF) and Decoupled Double Synchronous Reference Frame (DDSRF) PLL algorithms are implemented. A performance comparison is carried out under ideal and unbalanced utility condi…

Intraluminal Doppler-sonography: a new device for data analysis and its in vitro test

2002

Summary form only given. A special data acquisition unit has been developed which allows to process on-line not only the mean-phasic Doppler shift signal but also to analyze the spectral contents and the received A-mode signal. The probe consists of a 3f-catheter which is activated by a pulsed transmitter-receiver (Millar). The carrier frequency is 20 MHz and the impulse repetition rate is 62.5 kHz. Two modular A/D converters are used. One digitizes directly the Doppler shift frequencies in the range less than 20 kHz (sampling rate 100 kHz, resolution 12 bit); the other digitizes the RF-signal (sampling rate 200 MHz, resolution 8 bit). For further processing, data are transferred via separa…

On the design of a multiple-output DC/DC converter for the PHI experiment on-board of solar orbiter

2013

Power converters for experiments that have to fly on board space missions (satellite, launchers, etc.) have very stringent requirements due to its use in a very harsh environment. The selection of a suitable topology is therefore not only based on standard requirements but additional more strict ones have also to be fulfilled. This work shows the design procedure followed to build the Power Converter Module (PCM) for the Polarimetric and Helioseismic Imager (SO/PHI), experiment on board the Solar Orbiter Satellite. The selected topology has been a Push-Pull, for a power level of approximately 35 W and with seven output voltages. Galvanic isolation is needed from primary to secondary, but no…

High-Resolution and Low Resource Time To Digital Converters for the KM3NeT Neutrino Telescope

2015

MuPix10: First Results from the Final Design

2021

Many years of research and development of High Voltage Monolithic Active Pixel Sensors (HVMAPS) have culminated in the final design for the Mu3e pixel sensor. MuPix10 is a fully monolithic sensor with an active pixel matrix size of $20\times20\,\mathrm{mm}^2$ produced in the $180\,\mathrm{nm}$ HV-CMOS process at TSI Semiconductors. The pixel size is $80\times80\,\mathrm{\mu m}^2$. Hits are read out using a column-drain architecture and sent over up to four serial links with up to $1.6\,\left.\mathrm{Gbit}\middle/\mathrm{s}\right.$ each. By means of DC/DC converters and exclusive usage of on-chip biasing, MuPix10 is fully operable with a minimal set of electrical connections. This is an inte…

A Temperature Dependent Non-Linear Inductor Model for a DC/DC Boost Converter

2018

This paper is focused on the use of non-linear inductors in DC/DC switching converters, as well as their behaviour due to changes in current and temperature. The model of an inductor is set up on the basis of experimental data, which are automatically acquired by a virtual instrument; from those data, a polynomial curve describing the inductance variations is obtained. The analysis of the converter, performed by including the proposed model, is validated by experimental tests.

Power Quality Savings with Controlled Fault-Tolerant Power Converters

2011

Power quality is simply the interaction of electrical power with electrical equipments. If electrical equipments operate correctly and reliably without being damaged or stressed, a suitable level of power quality is assured. On the other hand, if the electrical equipment malfunctions, is unreliable, or is damaged during normal usage, power quality is poor and probably the economical loss could be preeminent over the technical one. In the scenario of the Distributed generation power quality issues will be more- over important because an higher dissemination of power conditioning equip- ment will be requested and this obviously will increase the sources of vulnera- bility for the electrical s…