Search results for "Design"
showing 10 items of 5885 documents
An FPGA-Based Software Defined Radio Platform for the 2.4GHz ISM Band
2006
A prototype of a Software Defined Radio (SDR) platform has been successfully designed and tested implementing a reconfigurable IEEE 802.11 and ZigBee receiver. The system exploits the reconfiguration capability of an FPGA for implementing a number of receiver configurations that share the same RF front-end. Configurations can be switched at run time, or can share the available logic and radio resource.
HEMT for low-noise microwaves: CAD-oriented performance evaluation
1995
This paper shows how a graphic processing of low-noise HEMT's small signal parameters, allows evaluating and comparing the actual performance obtainable in front-end applications. HEMT's tradeoff charts which solve tradeoffs among the basic low-noise amplifier performance are reported. Figures of merit for microwave low-noise HEMT which represent a fast way of evaluating HEMT in actual working conditions and of selecting the proper transistor, are defined. As an example, the tradeoff charts and the figures of merit of two HEMT's (Fujitsu FHR02FH, Sony 2SK677) and a pseudomorphic-HEMT (Celeritek CFB001-03) are reported and compared with the data sheets. © 1995, IEEE. All rights reserved.
Towards 100 % recycling of reclaimed asphalt in road surface courses: binder design methodology and case studies
2016
Reclaimed Asphalt (RA) has shown great potential to be reused in new asphalt mixtures, however its incorporation in top asphalt pavement layers is still very limited (10e30%). In fact, despite the advan- tages that its use implies, RA content in road pavement surface courses is still restricted in most countries due to mainly legislation limitations, but also some technical issues. This paper aims at being a step further to improve the latter by providing a methodology that allows producing fundamental inputs for confidently performing mix design of asphalt mixtures incorporating up to 100% RA. The methodology consists in an advanced preliminary binder's blend design that can be used with a…
Design, manufacturing and testing of a fast disconnecting system for the European target assembly concept of IFMIF
2013
The International Fusion Materials Irradiation Facility (IFMIF) will be equipped with a lithium target assembly to produce the required neutron flux for the irradiation of candidate fusion materials up to a damage rate of 100 dpa (cumulated damage in five years). The present European target assembly design is based on the so called replaceable backplate bayonet concept that was developed with the objective to simplify the maintenance operations for its refurbishment/replacement and to reduce the material for disposal as well. To this purpose it was also conceived to be attached to the lithium pipes and to the beam line by means of remotely operated connections based on clamped flanges with …
Determining the explosion risk level and the explosion hazard area for a group of natural gas wells
2016
Starting from the fact that the natural gas engineering profession is generally associated with a high occupational risk, the current paper aims to help increase the safety of natural gas wells and reduce the risk of work-related accidents, as well as the occurrence of professional illnesses, by applying an assessment method that has proven its efficiency in other industrial areas in combination with a computer-aided design software. More specifically, the paper focuses on two main research directions: assessing the explosion risk for employees working at natural gas wells and indicating areas with a higher explosion hazard by using a modern software that allows their presentation in 3D. Th…
Lighting control systems: Factors affecting energy savings' evaluation
2015
Abstract The use of automated lighting control systems allows to reduce lighting costs and to achieve significant energy savings. The energy performances of controls are affected by many factors, the impact of which is very difficult to account for during the design process. The goal of this paper is to describe the factors that influence the control systems’ energy performances, to analyze how the currently available calculation tools take them into account and finally to propose a simple method to adjust results obtained from the simulation software.
A simple and accurate model of photovoltaic modules for power system design
2014
Serviceability of segmental concrete arch-frame bridges built by cantilevering
2013
The evaluation of the safety degree in service life for a segmental prestressed concrete bridge built by the cantilever method presents different aspects related to strength, deformability, durability and to effects of time-dependent phenomena as creep and shrinkage. The case-study of a prestressed concrete frame bridge with inclined piers is presented, built by cantilevering, with precast segments. By considering the fundamental items of design and construction stages, the implications due to the arch effect in this static scheme are investigated, with respect to an equivalent bridge with a final scheme of continuous girder on vertical piers. The birth of a significant value of axial force…
Energy and environmental impacts of Energy related products (ErP): a case study of biomass-fuelled systems
2014
Abstract Energy-related Products (ErP) account for a large proportion of European energy and natural resource consumption. In 2007, ErP were responsible for the consumption of about 239 Mtoe of electricity and about 555 Mtoe of fuels. In order to reduce the energy and environmental impacts of these products, the European Commission published the Directive 2009/125/EC on the eco-design of ErP. This Directive represents a key component of European policy for improving the energy and environmental performances of products in the internal market. In this context, it is important to develop scientific research aimed at assessing the energy and environmental impacts of ErP, and at defining their …
Obtaining dynamic Norton parameters of a solar panel from manufacturer data
2016
Photovoltaic arrays have been shown to possess significant influence on the dynamic performance of coupled source-converter-load system while its dynamic resistance is the most important parameter, contributing to the overall system dynamics. In this paper, a method of deriving the parameters of linearized photovoltaic equivalent circuit from manufacturer data is proposed. The approach allows predicting the range of dynamic Norton parameters for the expected irradiation and temperature operation conditions thus defining clear bounds required for robust design of the system controller.