Search results for "Dose rate"

SU-E-T-508: Monte Carlo Dosimetric Study of the CSM40 Low Dose Rate Source

2013

Purpose: There is a LDR 137Cs brachytherapy source, CSM40, developed by Eckert & Ziegler BEBIG. Fundamental dosimetric datasets to be used on treatment planning systems do not exist for this source. This study aims to obtain quality dosimetric data for this source for its use in clinical practice as required by AAPM and ESTRO. Methods: Penelope2008 and GEANT4 Monte Carlo codes were used to characterize this source dosimetry. Water composition and mass density was that recommended by AAPM. Due to the typical energies of the 137 Cs, dose for small distances can be approximated by collisional kerma. Therefore, we have considered collisional kerma for r<20 cm. To provide adequate spatial resolu…

Technical note: Monte-Carlo dosimetry of the HDR 12i and Plus 192Ir sources.

2001

In this study a complete set of dosimetric data for the GammaMed high dose rate (HDR) 12i and Plus 192 Ir sources are presented. These data have been calculated by means of the Monte Carlo simulation code GEANT3. Absolute dose rate distributions in water are presented as conventional two dimensional (2D) Cartesian look-up tables, and in the TG43 formalism.

1989

A commercial low density polyethylene was irradiated by gamma irradiation at room temperature with different integrated doses and dose rates. The modifications induced in the material were studied by means of solubility and swelling measurements and related to structural modifications by calorimetric measurements. Results indicate that crosslinking prevails with respect to degradation at high dose rates and that the ageing phenomena occur essentially in the amorphous phase. Ein kommerzielles Polyethylen niedriger Dichte wurde bei unterschiedlicher integrierter Dosis und unterschiedlicher Dosisleistung bei Zimmertemperatur mit Gammastrahlung behandelt. Die Veranderungen des Materials wurden …

The influence of the processing temperature on gamma curing of epoxy resins for the production of advanced composites

2007

Abstract Gamma radiation curing of an epoxy monomer, in the presence of an iodonium salt, as initiator, is studied. Systems have been polymerized at the same irradiation dose and dose rate and at different processing temperatures. The experimental results show that all the irradiated materials exhibit a latent reactivity, undergoing toward an increase of crosslinking density if they are thermally cured after irradiation. The results indicate that the processing temperature affects both the crosslinking density after irradiation and the sensibility to the post-irradiation thermal treatment.

Fitted dosimetric parameters of high dose-rate 192Ir sources according to the AAPM TG43 formalism

2001

The purpose of this study is to find fitted functional forms to the anisotropy function, F(r,θ), and the radial dose function, g(r), in order to characterize dose-rate distributions around all the high-intensity 192 Ir sources currently in use. Dosimetry data are at present available as tables for: the microSelectron HDR (“classic” and “new” design models), the PDR source, and the VariSource HDR source, expressed in terms of the AAPM Task Group No. 43 recommendations. There is only one paper out which introduces a functional form to fit the anisotropy function, but only for symmetric sources with respect to the transverse axis. However, dosimetric data of the HDR and PDR sources mentioned a…

Monte Carlo dosimetric study of the BEBIG Co-60 HDR source

2005

Although not as widespread as Ir-192, Co-60 is also available on afterloading equipment devoted to high dose rate brachytherapy, mainly addressed to the treatment of gynaecological lesions. The purpose of this study is to obtain the dosimetric parameters of the Co-60 source used by the BEBIG MultiSource remote afterloader (BEBIG GmbH, Germany) for which there are no dosimetric data available in the literature. The Monte Carlo code GEANT4 has been used to obtain the TG43 parameters and the 2D dose rate table in Cartesian coordinates of the BEBIG Co-60 HDR source. The dose rate constant, radial dose function and anisotropy function have been calculated and are presented in a tabular form as w…

Characterisation of two new radiochromic gel dosimeters TruView™ and ClearView™ in combination with the vista™ optical CT scanner: A feasibility study

2018

This study aims at characterising the properties of TruView™ and ClearView™ two new gel dosimeters (Modus Medical Devices Inc.) and at studying the feasibility of relative dosimetry using these dosimeters and the Vista™ Optical CT scanner to accurately evaluate dose.In this work, we investigated key dosimetric aspects (dose response, energy and dose rate dependence) and stability of these radiochromic gels initiated in preliminary works (Huet et al., 2017; Colnot et al., 2017) using spectrophotometric measurements. Moreover, by mean of optical CT scanning (Vista™), their performances to measure relative depth dose (PDD) and cross profiles were analysed.TruView™ and ClearView™ present a line…

Low Dose-Rate, High Total Dose Set-Up for Rad-Hard CMOS I/O Circuits Testing

2017

In this paper, the planning of low dose-rate, high total dose testing campaign for I/O circuits is reported. In particular, the paper describes all development steps, starting from the rad-hard I/O circuits design and the implementation of the test-chip, which is meant to allow comparative testing between rad-hard and standard devices. The designed experimental setup permits in situ measurements, therefore the circuits behavior can be remotely monitored for very long periods. This feature enables low dose-rate testing up to very high dose.

FMECA Analyses of radiological over-exposure accident to patients in brachytherapy

2012

This paper presents safety analyses of accidental events which can involve patient during High Dose Rate brachytherapy treatment in over-exposures. The study has been performed by using the well-known techniques FMECA modified by Fuzzy logic theory. Moreover, fuzzy HEART methodology was employed in order to evaluate human error probabilities for each treatment stage. The obtained results, aimed to obtain a list of the deviations with a reasonable probability to produce significant adverse outcomes, provided some recommendations for procedures and safety equipments to reduce the occurrence of radiological over-exposure accidents.

Dosimetry comparison between TG-43 and Monte Carlo calculations using the Freiburg flap for skin high-dose-rate brachytherapy

2012

Abstract Purpose The purpose of this work was to evaluate whether the delivered dose to the skin surface and at the prescription depth when using a Freiburg flap applicator is in agreement with the one predicted by the treatment planning system (TPS) using the TG-43 dose-calculation formalism. Methods and Materials Monte Carlo (MC) simulations and radiochromic film measurements have been performed to obtain dose distributions with the source located at the center of one of the spheres and between two spheres. Primary and scatter dose contributions were evaluated to understand the role played by the scatter component. A standard treatment plan was generated using MC- and TG-43-based TPS appl…