Search results for "Electrical & Electronic"
showing 10 items of 489 documents
Metrological performances of voltage and current instrument transformers in harmonics measurements
2018
In the new electrical system scenario, the increasing presence of non-linear loads and renewable energy sources makes the measurement of harmonics an essential task. The accuracy of harmonic measurement firstly depends on the used instrument transformers for voltage and current sensing. Since the behavior of instrument transformers in non-sinusoidal conditions is not always well defined, this paper presents an experimental study on the metrological performances of current and voltage instrument transformers (CTs and VTs) in the presence of harmonics. Proper tests procedures are defined and measurement setups are developed for both CTs and VTs calibration. The analysis is carried out by usin…
Design and Realization of a Bidirectional Full Bridge Converter with Improved Modulation Strategies
2020
In this paper a Full-Bridge Converter (FBC) for bidirectional power transfer is presented. The proposed FBC is an isolated DC-DC bidirectional converter, connected to a double voltage source&mdash
Establishing material hygrothermal characteristics via long-term monitoring and best-fit numerical models
2020
Numerical models of heat and moisture transfer for performance forecast of lightweight insulating assemblies require many inputs. These include exterior climate data (i.e. temperature, relative humidity, solar radiation), interior climate data or standard models, transfer coefficients, correct initial conditions, etc. Most importantly, one needs reliable material models. A material model includes porosity, density, heat capacity, but also non-constant properties, such as thermal conductivity, vapor/liquid water diffusivity, sorption curves. These are, in general, difficult to determine, and material database entries often are incomplete, or simply non-existent. However, if one performs long…
A Cost-Effective Solution for Clearing High-Impedance Ground Faults in Overhead Low-Voltage Lines
2019
Downed distribution conductors in overhead distribution systems may not be a concern for equipment but greatly challenge the safety of persons, as well as the integrity of properties. Standard overcurrent protective devices may not be able to detect the magnitudes of currents resulting from high-impedance ground faults. Sophisticated relays able to detect high-impedance ground faults have been available to electric utilities. However, their implementation is rather uncommon, especially in developing countries, most likely due to their costs. In this paper, the authors formalize the problem, and propose a possible cost-effective solution for low-voltage overhead lines with neutral wire. This…
Min-Type Control Strategy of a DC-DC Synchronous Boost Converter
2019
International audience; This paper presents the analysis and design of a min-type strategy to control a synchronous boost converter in continuous conduction mode. The strategy uses a nonlinear switching surface to establish the change of topology in the converter and is analyzed by means of a sliding-mode control approach. Subsequently, the min-type strategy is modified by a hybrid control formulation, which introduces a hysteresis width and a dwell-time to obtain a finite switching frequency in the start-up and steady-state respectively. The hybrid control formulation is implemented digitally by means of a microprocessor which processes the samples of inductor current and capacitor voltage…
Design and Performance Evaluation of a High Power-Density EMI Filter for PWM Inverter-Fed Induction-Motor Drives
2016
This paper presents the design of an electromagnetic interference (EMI) filter for a low-voltage high-current induction-motor drives supplied by dc power grids. In order to effectively design the EMI filter, a suitable common-mode/differential-mode (CM/DM) separation technique has been used. Due to the high operating currents, the software-based separation technique using time-domain measurements has been applied. The proposed technique allows the CM and DM sections of the EMI filter to be properly selected in a more economical way, i.e., without the need of a dedicated hardware or costly radio frequency (RF) instrumentation. The design has been done according to a power-density criterion. …
Extending the Power Range of a Solar Inverter
2018
Solar inverters feature a minimum and maximum limit of the maximum power point voltage. Overcoming these limits leads to a disconnection of the power equipment, thus wasting the solar energy. In this paper, a solution to extend the power range of a solar inverter is presented. The proposed solution extends he minimum maximum power point limit of a commercial solar inverter by means of a battery energy storage system, including a DC/DC power converter. The battery energy storage system is connected in series to the photovoltaic module. If the photovoltaic module voltage drops below the minimum maximum power point limit, the battery energy storage system is enabled thus boosting the input vol…
An Innovative Coupling Solution for Power Line Communication in MV Electrical Networks
2019
One of the main problems in the diffusion of power line communication (PLC) in medium voltage (MV) networks is the need of a dedicated PLC coupler to be installed all over the network. To avoid this problem, the authors have studied, prototyped and patented an innovative PLC coupling solution which uses electrical elements embedded in most of the switchgears already installed in MV networks, i.e. the capacitive dividers of the voltage detecting systems (VDS). The new solution prototype is described in this paper, highlighting the advantages in terms of a significant reduction of both direct costs of equipment and infrastructures and indirect costs of installation and service interruption. T…
Active disturbance rejection control of linear induction motor
2017
This paper proposes the theoretical framework and the experimental application of the active disturbance rejection control to linear induction motors. Such a nonlinear control (ADRC) technique can be viewed as a particular kind of input-output linearization control, where the nonlinear transformation of the state is not computed by means of the model, but it is estimated online. Such an approach permits to cope with unmodelling dynamics, as well as uncertainty in the knowledge of the model parameters and exogenous disturbances. The effectiveness of the proposed ADRC control law has been verified both by numerical simulations and experimentally on a suitably developed test setup. Moreover, t…
A Model for the Study of Sheath Currents in Medium Voltage Cables for Industrial Application
2020
In this paper, the implementation of a simulation model for studying the effect of cross-bonding of metallic sheaths and/or non-magnetic armor of single-core medium voltage cables in the same circuit is discussed. With the use of single-core cables, the resistive losses due to the induced circulating currents in cable sheaths or armors causes an increase of cable temperature that reduces its ampacity. In addition, the risk of electric shock due to induced voltages may be present if a person is exposed to the armor/sheath at the unbounded end. For this reason, special bonding techniques are used to significantly reduce these currents. The authors have implemented a model that could be used t…