Search results for "Electromagnetic compatibility"
showing 10 items of 35 documents
Experimental EMF characterization of a secondary substation
2015
This paper presents the results of the experimental EMC characterization of a new medium/low voltage (MV/LV) secondary substation, which was developed in the framework of the research project "NEW CAB ELARC". It has two MV/LV transformers, with total rated power of 1000 kVA. To perform the experimental characterization, firstly an analysis was performed of the Italian and European standards recommendations. Different approaches were highlighted and the most appropriate procedures were identified for the measurement of the magnetic fields emissions, at power systems frequency (50 Hz) in steady-state conditions. A dedicated test lab was set up for the secondary substation characterization. Th…
Numerical investigation of the induced voltage on a cable placed at random locations inside a metallic enclosure
2008
In this paper, we investigate the induced voltage on a cable when placed at random locations inside a metallic enclosure. The analysis consists of a cable of defined length and fixed terminals, but different layouts, placed in a metallic enclosure containing an aperture. The induced voltages for the different layouts are computed for a plane wave incident on the aperture. A second analysis is performed with no cable (i.e., an empty enclosure) and the results are compared to those for the cable present. The results are compared to the resonance frequencies of the closed cavity and the aperture.
Immunity of a Virtual Instrument to conducted electromagnetic disturbances
2004
In the paper the performances of the Virtual Instruments under conducted electromagnetic disturbances are investigated, in order to find out if and how their metrological characteristics change with respect to the ones measured in absence of electromagnetic threats. The analysis is carried out by means of experimental tests, subjecting the AC power port of the systems under test to the conducted disturbances considered by the IEC-61326 standard and following the test procedures prescribed in the IEC-61000-4-series standards. The results show that the tested measurements instruments are sufficiently immune to these disturbances, since no variations of the distinctive parameters have been obs…
Virtual Instruments: Uncertainty Evaluation in the Presence of Electromagnetic Interferences
2007
The electromagnetic interferences can influence the performances of a virtual instrument; consequently, in a generic measurement performed by using these instruments, the related uncertainty values can increase. In the paper, we report the results of various experimental tests performed with the aim to check if and how the radiated and/or conducted disturbances affect the instruments' characteristics and, in particular, the single uncertainty sources. Starting from these results and applying an already proposed method for the uncertainty estimation in the measurements performed by means of virtual instruments, it is possible to take into account and to evaluate the contribute of the electro…
Wind Electrical energy generating systems EMC. A dedicated experimental simulator for tests
2008
In wind electrical energy generating systems, due to fast voltage and current fluctuations, the power converter represents a source of electromagnetic disturbances. EMI problems of stand alone wind generators are here analysed in order to take into account many different power quality problems which result in voltage fluctuations and harmonics in the net. This paper, moreover, presents a wind turbine experimental simulator (WTES) that moves a wind electrical energy generating system (WEEGS) to carry out EMI measurements and the relative experimental results. The WEEGS here taken into account comprises a wound rotor induction generator (WRIG) in which the frequency transformation from the ro…
Impact of industrial environments on the PC-based measurements
2007
In the paper we present a simple and fast procedure to evaluate the impact of the electromagnetic disturbances, which can be present in the industrial locations, on the measurements performed by a generic PC-based measurement instrument. The method is conceived starting from the data obtained by subjecting the instruments to the disturbances prescribed by the IEC-61326 standard. The results show that, even under heavy disturbances, the common good practices of shielding and grounding allow a correct employment of this kind of instrumentation.
2-D approach to the analysis of semianechoic chambers using a hybrid technique
2003
Semianechoic chambers are the most widely used emplacements for electromagnetic compatibility (EMC) tests. In this work a new and efficient technique for the analysis of 2-D simplified model of a chamber with arbitrary absorber is introduced and validated Some advanced results are presented, and a 2-D figure of merit for studying the overall behaviour of the chamber is proposed.
Evaluation of radiated EMI in 42 V vehicle electrical systems by FDTD simulation
2007
In this paper a full 3D numerical scheme, based on the finite difference time domain method, is used to predict the electromagnetic radiated interference generated by 42 V vehicle power electronic driven electrical loads. An experimental set-up has been arranged on purpose in order to validate the proposed simulation tool. To this aim, the features of a semi-anechoic electromagnetic chamber have been exploited in order to operate in a shielded test site for the measurement of near field radiated emissions. Two different three-dimensional geometrical configurations of realistic vehicle installations of the loads, are studied. A comparative analysis among measured and computed results is perf…
A local linear black-box identification technique for power converters modeling
2009
In this paper, a black-box modeling technique for power electronic converters, also used in automotive environment is presented. The aim of this work is to provide a simple yet versatile and powerful tool to schematize complex electric devices in vehicular appliances, in order to fulfill the electromagnetic compatibility already during the project stage. By using input and output measured data, a composite local linear state space model is built up. Radial basis functions are used as weights for the local systems. The proposed approach is validated and applied in modeling a DC/DC converter for DC motors, a pulse width modulation inverter and a controlled rectifier.
Electromagnetic immunity analysis of a new interface device with power line communication for smart grid and energy storage applications
2013
An analysis of EMC standards related to smart grid devices with PLC port has been carried out and the standardization lacks have been pointed out with reference to the evaluation of electromagnetic immunity to narrowband, coming from other communication systems connected to the grid, and RF disturbances conducted disturbances, usually present in a power grid. In particular, the paper analyses the electromagnetic conducted immunity of a new interface protection device (ID) for smart grid and energy storage applications. The new ID is equipped with a measuring board, a STM32 microcontroller, for data elaboration and memorization, and a ST7580 N-PSK powerline transceiver. An experimental test …