Search results for "Electromagnetic shielding"
showing 10 items of 79 documents
Charge measurement using an array of Faraday’s Cups on a printed circuit board
2014
Abstract An absolute method of measuring charge is to use a Faraday Cup (FC) principle. This study relates to a novel method of measuring charge on a flat substrate, which is coated with charged powder particles. The substrate consists of an array of FC with different dimensions. The sensor is manufactured using flame-retardant printed circuit board (PCB) technology. The objective of this work is to reduce the charge sharing by developing a grounded shield cup around each conductive cup in the array and accordingly increase cup-to-ground capacitance. The results have confirmed that the improved well shielding would provide a more accurate quantitative charge measurement.
Impact of industrial environments on the PC-based measurements
2007
In the paper we present a simple and fast procedure to evaluate the impact of the electromagnetic disturbances, which can be present in the industrial locations, on the measurements performed by a generic PC-based measurement instrument. The method is conceived starting from the data obtained by subjecting the instruments to the disturbances prescribed by the IEC-61326 standard. The results show that, even under heavy disturbances, the common good practices of shielding and grounding allow a correct employment of this kind of instrumentation.
Radiation leakage study for the Valencia applicators
2011
Abstract Introduction and purpose The Valencia applicators which are accessories of the microSelectron-HDR afterloader (Nucletron, Veenendaal, The Netherlands) are designed to treat skin lesions. These cup-shaped applicators are an alternative to superficial/orthovoltage x-ray treatment units. They limit the irradiation to the required area using tungsten-alloy shielding, and are equipped with a tungsten-alloy flattering filter allowing the treatment of skin tumors, the oral cavity, vaginal cuff, etc. The tungsten-alloy thickness to shield radiation is not the same in all parts of the applicators. This fact led us to question whether the leakage radiation differs depending on where it is me…
33S hyperfine interactions in H2S and SO2 and revision of the sulfur nuclear magnetic shielding scale
2014
Using the Lamb-dip technique, the hyperfine structure in the rotational spectra of H2(33)S and (33)SO2 has been resolved and the corresponding parameters--that is, the sulfur quadrupole-coupling and spin-rotation tensors--were determined. The experimental parameters are in good agreement with results from high-level coupled-cluster calculations, provided that up to quadruple excitations are considered in the cluster operator, sufficiently large basis sets are used, and vibrational corrections are accounted for. The (33)S spin-rotation tensor for H2S has been used to establish a new sulfur nuclear magnetic shielding scale, combining the paramagnetic part of the shielding as obtained from the…
Dosimetric perturbations of a lead shield for surface and interstitial high-dose-rate brachytherapy.
2014
In surface and interstitial high-dose-rate brachytherapy with either (60)Co, (192)Ir, or (169)Yb sources, some radiosensitive organs near the surface may be exposed to high absorbed doses. This may be reduced by covering the implants with a lead shield on the body surface, which results in dosimetric perturbations. Monte Carlo simulations in Geant4 were performed for the three radionuclides placed at a single dwell position. Four different shield thicknesses (0, 3, 6, and 10 mm) and three different source depths (0, 5, and 10 mm) in water were considered, with the lead shield placed at the phantom surface. Backscatter dose enhancement and transmission data were obtained for the lead shields…
Pyrolysed cork-geopolymer composites: A novel and sustainable EMI shielding building material
2019
Abstract In this investigation, and for the first time, pyrolysed sustainable cork was used to produce waste-based geopolymer-cork composites with enhanced electromagnetic interference (EMI) shielding properties. The influence of the pyrolysed cork amount and the geopolymer porosity on the EMI shielding ability of the composites was studied. The maximum total shielding effectiveness (SET) values achieved by these novel building materials (−13.8 to −15.9 dB) are equal to any other reported geopolymer microwave (MW) absorbers over the X-band, despite containing much lower carbon content. In addition, our composites were produced using an industrial waste (biomass fly ash) as raw material and …
Superconducting Solenoid System with Adjustable Shielding Factor for Precision Measurements of the Properties of the Antiproton
2019
Physical review applied 12(4), 044012 (2019). doi:10.1103/PhysRevApplied.12.044012
Improving the Efficiency of NFC Systems Through Optimizing the Sintered Ferrite Sheet Thickness Selection
2020
The reduction of embedded portable devices involves a magnetic field interference problem when it integrates near field communication (NFC) due to the presence of conductive surfaces, such as ground planes, batteries, or metallic enclosures. Flexible sintered ferrite sheets (FSFS) represent an interesting shielding solution to prevent electromagnetic interferences problems related to NFC, thanks to their ability to control the magnetic flux. The characterization of FSFS effectiveness is analyzed as a function of the sheet thickness in this contribution. This is performed with the aim of determining which is the optimum thickness value to retune an NFC antenna to its original operation frequ…
Electromagnetic shielding efficiency in Ka-band: carbon foam versus epoxy/carbon nanotube composites
2012
The wide application of microwaves stimulates searching for new materials with high electrical conductivity and electromagnetic (EM) interference shielding effectiveness (SE). We conducted a comparative study of EM SE in K a -band demonstrated by ultra-light micro-structural porous carbon solids (carbon foams) of different bulk densities, 0.042 to 0.150 g/cm 3 , and conventional flexible epoxy resin filled with carbon nanotubes (CNTs) in small concentrations, 1.5 wt.%. Microwave probing of carbon foams showed that the transmission through a 2 mm-thick layer strongly decreases with decreasing the pore size up to the level of 0.6%, due to a rise of reflectance ability. At the same time, 1 mm…
The Magnetic Properties of Electrical Pulses Delivered by Deep-Brain Stimulation Systems
2020
The aim of this article is to analyze the magnetic field properties for both the monopolar and bipolar electrode configurations of deep-brain stimulation electrodes using 3-D magnetic field measurements and to investigate if the magnetic measurements enable a localization of the electrode as a proof of concept. Therefore, a simplified head phantom with an integrated deep-brain stimulation electrode was created to measure the magnetic flux densities in all the three dimensions with a fluxgate magnetometer over a sensor trajectory of measuring points inside the magnetically shielded chamber. The magnitude of the magnetic flux density for monopolar stimulation and bipolar stimulation is in the…