Search results for "Element analysis"
showing 10 items of 105 documents
New experimental molecular stopping cross section data of Al2O3, for heavy ions
2014
Abstract Molecular stopping cross section data of Al2O3, for heavy ions of 12C, 16O, 28Si, 35Cl, 79Br within the energy range of 0.01–1.0 MeV/nucleon were measured. Both direct transmission and bulk analysis methods were applied. Stopping cross sections were calculated both with the SRIM and MSTAR codes. Evaluation and intercomparison of the new data with the calculated and previously measured ones are reported in this paper.
Effects of clearance on thick, single-lap bolted joints using through-the-thickness measuring techniques
2011
Composite materials have increasingly become more common in ground transportation. As this occured thicker panels, as compared to composite panels used in aviation, become necessary in order to withstand high impact loads and day to day degradation. The effectiveness of these panels was often limited by the strength of the joint in which the panel was attached to the frame of the vehicle. Investigating methods of reducing strain concentrations within these joints would increase the effectiveness in using composite materials in ground transportation applications by increasing the load necessary for joint failure to occur. In this study, fiber optic strain gages were embedded in a composite p…
Efficient photo-thermal activation of gold nanoparticle-doped polymer plasmonic switches
2012
International audience; We report on the photo-thermal activation of dielectric loaded plasmonic switches comprised of gold nanoparticle-doped polymer deposited onto a gold film. The plasmonic switches rely on a multi-mode interferometer design and are fabricated by electron beam lithography applied to a positive resin doped with gold nanoparticles at a volume ratio of 0.52%. A cross-bar switching is obtained at telecom wavelengths by pumping the devices with a visible beam having a frequency within the localized surface plasmon resonance band of the embedded nanoparticles. By comparing the switching performances of doped and undoped devices, we show that for the modest doping level we cons…
Mechanical behavior of implant assisted removable partial denture for Kennedy class II
2019
Made available in DSpace on 2020-12-12T01:22:13Z (GMT). No. of bitstreams: 0 Previous issue date: 2020-01-01 Background: This study evaluated the mechanical response of a removable partial denture (RPD) in Kennedy Class II according to being associated or not with implants. Material and Methods: Four RPDs were manufactured for a Kennedy Class II: CRPD-Conventional RPD, RPD+ 1M, RPD+2M and RPD+12M, respectively, signifying implant assisted RPDs with the implant installed in the first molar, second molar, and in the first and second molars. The finite element method was used to determine the most damaged support tooth under compressive load (300N, 10s) and strain gauge analysis was used to ev…
A Statistical Model of Spine Shape and Material for Population-Oriented Biomechanical Simulation
2021
In population-oriented ergonomics product design and musculoskeletal kinetics analysis, digital spine models of different shape, pose and material property are in great demand. The purpose of this study was to construct a parameterized finite element spine model with adjustable spine shape and material property. We used statistical shape model approach to learn inter-subject shape variations from 65 CT images of training subjects. Second order polynomial regression was used to model the age-dependent changes in vertebral material property derived from spatially aligned CT images. Finally, a parametric spine generator was developed to create finite element instances of different shapes and m…
Patient-specific simulation of the intrastromal ring segment implantation in corneas with keratoconus
2015
Purpose The purpose of this study was the simulation of the implantation of intrastromal corneal-ring segments for patients with keratoconus. The aim of the study was the prediction of the corneal curvature recovery after this intervention. Methods Seven patients with keratoconus diagnosed and treated by implantation of intrastromal corneal-ring segments were enrolled in the study. The 3D geometry of the cornea of each patient was obtained from its specific topography and a hyperelastic model was assumed to characterize its mechanical behavior. To simulate the intervention, the intrastromal corneal-ring segments were modeled and placed at the same location at which they were placed in the s…
Design of a Close Power Loop Test Bench for Contra-Rotating Propellers
2020
The aim of the research is to develop an azimuthing contra-rotating propeller for commercial applications with a power of 2000 kW. The thruster system is designed especially to be installed on high speed crafts (HSCs) for passenger transport with a cruising speed of about 35–40 knots. The topic is very useful because the azimuth thruster solutions currently do not find commercial applications in naval units for passenger transport. The latter are heavy, not very efficient from a hydrodynamic point of view and suitable for maximum cruising speed of about 18–20 knots. The study is interesting because among the advantages that these solutions provide are the possibility of transmitting very hi…
Platform switching on wide-diameter external hex implants: a finite element analysis.
2012
Objectives: The objective of this work was to use finite element analysis to compare the effect of forces coming to bear on abutments 4.1 or 5.0 mm in diameter connected to a 5.0 mm implant (i.e. with or without platform swit - ching). Study design: A 3D CAD model of a 5 x 11.5 mm external hex implant was developed, complete with a connection screw and either of two abutments, one 4.1 and the other 5 mm in diameter, to assess the influence of two loading conditions, i.e. 200 N loaded either axially or off center on the top of the abutment. Results and conclusions: In the symmetrically loaded models, greater stresses were transmitted to the bone in the area below the neck of the implant in t…
3D Data Acquisition and Numerical Analysis of a Footwear in Walking
2004
The aim of the paper is to set a procedure to study the load history of a footwear during a step with non-linear FE analysis. The geometric model tested was reconstructed from a real shoe by means of Reverse Engineering process, starting from dense point clouds acquired by non-contact scanning system. For each phase of the walk, the pressure values are obtained by a pressure distribution platform when tester is walking along the platform. The Finite Element model is easily generated by Hypermesh software using the CAD model. Ansys software is used to perform non-linear analyses. The procedure can be employed for improving the product performance in terms of durability, flexibility and comfo…
A macro-modelling approach for the analysis of infilled frame structures considering the effects of openings and vertical loads
2015
During the last decades, several macro-models have been proposed for the modelling of the infill panels' contribution to the lateral strength of frames. Despite all this effort, a robust model, which takes into account the influence of the vertical load, is not yet available. Furthermore, the influence of the very common case of infill walls with openings, such as windows and doors, has been neglected in all the code provisions that have been published so far. In this paper, an updated macro-model, based on the equivalent pin-jointed diagonal compressive strut, is presented. The proposed macro-model is able to represent the stiffening effect of the infill panel with openings by taking into …