Search results for "Engineering sciences"
showing 10 items of 2347 documents
Clustering Analysis of Questionnaire for Ph.D. studies in Electrical and Information Engineering in Europe
2013
The ELLEIEC ERASMUS thematic network was running from October 2008 to September 2011. This project deals with several aspects linked to Lifelong Learning in Electrical and Information Engineering in Europe. Within this project, Task 4 is dedicated to “Implementation issues across EIE”. The idea of this task was to see how we can, thanks to implementation using Programs available from the European Commission, and associates (ERASMUS, CD, ERASMUS-MUNDUS, ATLANTIS, IP) to emphasize and develop mobility and cross-recognition. Another aspect, strongly connected, was to analyze the existing and possible interactions of Higher Education Institutions and Lifelong Learning. The European consortium o…
Single molecules probe local density of modes (LDOS) around photonic nanostructures
2008
International audience; According to Fermi's golden rule, the fluorescence decay rate is directly proportional to the projected local density of photonic modes (LDOS) at the molecule location. The relevant LDOS depends on the molecule orientation. In this paper, the direct measurement of the fluorescence lifetime near gold dot photonic structures is investigated and compared to calculated LDOS. Detailed analysis of the decay channels is presented on the basis of numerical simulations.
Microfabrication of hybrid fluid membrane for microengines
2015
International audience; This paper describes the microfabrication and dynamic characterization of thick membranes providing a technological solution for microengines. The studied membranes are called hybrid fluid-membrane (HFM) and consist of two thin membranes that encapsulate an incompressible fluid. This work details the microelectromechanical system (MEMS) scalable fabrication and characterization of HFMs. The membranes are composite structures based on Silicon spiral springs embedded in a polymer (RTV silicone). The anodic bonding of multiple stacks of Si/glass structures, the fluid filling and the sealing have been demonstrated. Various HFMs were successfully fabricated and their dyna…
Extremely rapid acclimation of Escherichia coli to high temperature over a few generations of a fed-batch culture during slow warming
2014
This study aimed to demonstrate that adequate slow heating rate allows two strains of Escherichia coli rapid acclimation to higher temperature than upper growth and survival limits known to be strain-dependent. A laboratory (K12-TG1) and an environmental (DPD3084) strain of E. coli were subjected to rapid (few seconds) or slow warming (1 degrees C 12 h(-1)) in order to (re) evaluate upper survival and growth limits. The slow warming was applied from the ancestral temperature 37 degrees C to total cell death 46-54 degrees C: about 30 generations were propagated. Upper survival and growth limits for rapid warming (46 degrees C) were lower than for slow warming (46-54 degrees C). The thermal l…
Bi-objective multi-layer location–allocation model for the immediate aftermath of sudden-onset disasters
2019
International audience; Locating distribution centers is critical for humanitarians in the immediate aftermath of a sudden-onset disaster. A major challenge lies in balancing the complexity and uncertainty of the problem with time and resource constraints. To address this problem, we propose a location–allocation model that divides the topography of affected areas into multiple layers; considers constrained number and capacity of facilities and fleets; and allows decision-makers to explore trade-offs between response time and logistics costs. To illustrate our theoretical work, we apply the model to a real dataset from the 2015 Nepal earthquake response. For this case, our method results in…
Managing in-country transportation risks in humanitarian supply chains by logistics service providers: Insights from the 2015 Nepal earthquake
2017
International audience; Humanitarian supply chains (HSCs) play a central role in effective and efficient disaster relief operations. Transportation has a critical share in HSCs and managing its risks helps to avoid further disruptions in relief operations. However, there is no common approach to or culture of risk management that its applicability has been studied through recent cases. This paper incorporates an empirical research design and makes a threefold contribution: first, it identifies in-country transportation risks during Nepal response. Second, we evaluate afore identified risks through an expert driven risk assessment grid. Third, we use our field data to study how some humanita…
Dynamic Modeling and Driving Cycle Prediction for a Racing Series Hybrid Car
2014
International audience; This paper presents Noao, a plug-in series hybrid racing car equipped with an engine/generator set as range extender. To determine the velocity profile, i.e., performance of the car and its power profile, a dynamic model for this car is developed using pedal position as input. This value is easy to measure, representative for race cycles, and presents a novelty. The model is validated with the results from experiments. An analysis based on the map of Magny-Cours racing circuit and drivers pedal action on certain zones of the circuit is formulated and is used as a prediction tool to determine drivers inputs on other racing circuits and generate driving schedules. The …
Mechanical characterization of bio-based composite/metal laminates for an application in street furniture
2019
In this work, it is proposed to study the influence of three manufacturing parameters in the development of bio-basedcomposite/steel hybrids. These parameters arethe methodof assembly between composite and metal, the distribution of composite and steellayers throughthe thicknessof the hybrid,and the stacking sequence of the composite part of the hybrid. The study was conducted through impact tests at different energies and quasi-static three-point bending tests. For each of these parameters, the influenceon the mechanical properties of the hybrid is evaluated.The results show that these properties depend essentially on the relative distribution of steel and composite through the thickness.
Application of gas separation membranes to detritiation systems
2002
The use of gas separation membranes in tritium removal systems has been studied to develop a new detritiation process. The main advantage of this new process is to reduce the number and/or the size of equipments in comparison to conventional detritiation systems. The objective of this study is to choose the best suited membrane for this application. The hydrogen or its isotopes recovery performance of several commercial hollow fiber organic membranes has been analyzed thanks to three devices. Experiments are performed with small quantities of hydrogen gas or deuterium gas or tritium gas in the range representative of the radioactive contamination level in tritium handling gloveboxes. A math…
Neutron-Induced Effects on a Self-Refresh DRAM
2022
International audience; The field of radiation effects in electronics research includes unknowns for every new device, node size, and technical development. In this study, static and dynamic test methods were used to define the response of a self-refresh DRAM under neutron irradiation. The neutron-induced effects were investigated and characterised by event cross sections, soft-error rate, and bitmaps evaluations, leading to an identification of permanent and temporary stuck cells, single-bit upsets, and block errors. Block errors were identified in different patterns with dependency in the addressing order, leading to up to two thousand faulty words per event, representing a real threat fr…