Search results for "Environmental engineering"
showing 10 items of 2674 documents
Biological minimization of excess sludge in a membrane bioreactor: Effect of plant configuration on sludge production, nutrient removal efficiency an…
2018
Abstract Excess sludge minimization was studied in a MBR with pre-denitrification scheme. Sludge minimization, nitrogen removal performance and membrane fouling tendency were investigated in two configurations, characterized by a different position of the sludge retention reactor (SRR). In particular, the SRR was placed: i) in the return activated sludge line (Anaerobic Side-Stream Reactor – ASSR configuration) and ii) in the mainstream between the anoxic and aerobic reactor (Anaerobic Main-Stream Reactor – AMSR configuration). The achieved results demonstrated that the ASSR enabled a higher excess sludge reduction (74% vs 32%), while achieving lower biological nitrogen removal (BNR) (TN = …
Integrated fixed-film activated sludge membrane bioreactors versus membrane bioreactors for nutrient removal: A comprehensive comparison
2018
Abstract This research elucidates the pollutants (nutrients and carbon) removal performance and nitrous oxide (N2O) emissions of two pilot plants. Specifically, a University of Cape Town (UCT) Membrane Bioreactor (MBR) plant and an Integrated Fixed Film Activated Sludge (IFAS)-UCT-MBR plant were investigated. The plants were fed with real wastewater augmented with acetate and glycerol in order to control the influent carbon nitrogen ratio (C/N). The short-term effect of the inlet C/N ratio variation (C/N = 5 mgCOD/mgN and C/N = 10 mgCOD/mgN) on the behaviour of both plants was investigated. The results showed that the IFAS-UCT-MBR configuration provided the best performance in terms of poll…
Suspended and attached biomass in an mbr system treating high strength wastewater Loads
2012
abstract
A comprehensive integrated membrane bioreactor model for greenhouse gas emissions
2018
Abstract A comprehensive integrated membrane bioreactor (MBR) model for wastewater treatment is here proposed. The model quantifies the main biological and physical processes. The model describes the biological removal of organic matter, nitrogen and phosphorus including greenhouse gases (carbon dioxide, CO 2 and nitrous oxide, N 2 O). The model takes into account the following main innovative aspects jointly: i. Two-step nitrification process; ii. N 2 O formation due to ammonia-oxidizing bacteria as a product of the hydroxylamine oxidation (NH 2 OH) and of the nitrite (NO 2 − ) reduction; iii. Soluble microbial product (SMP) formation/degradation due to microbial growth and endogenous resp…
Membrane bioreactors for treatment of saline wastewater contaminated by hydrocarbons (diesel fuel): An experimental pilot plant case study
2016
Abstract The paper reports the main results of an experimental campaign performed on a membrane bioreactor pilot plant designed to treat synthetic shipboard slops. The experimental campaign was divided into two phases: salinity acclimation up to 20 g NaCl L −1 (Phase I) and hydrocarbon (diesel fuel) dosing (Phase II). The observed results show that the carbon removal was not severely affected by the wastewater features. Conversely, respirometric tests showed that nitrification was strongly affected by the salinity (33% of nitrification efficiency at 20 g NaCl L −1 – Phase I) as a result of the salinity in the autotrophic biomass. Moreover, the sludge viscosity increased during Phase II due …
Performance of a MBR pilot plant treating high strength wastewater subject to salinity increase: Analysis of biomass activity and fouling behaviour
2013
Membrane bioreactors produce high quality effluents that could be suitable for reuse. However, when treating high strength wastewater subject to a salinity increase, a modification of biomass characteristics may occur. This circumstance is of importance, since it can have a significant impact in terms of biokinetic as well as fouling behaviour. The aim of the study was to evaluate the performance of a pilot plant MBR, in terms of biomass activity and membrane fouling, fed with high strength synthetic wastewater, when subject to a salinity increase. With normal salinity, the pilot plant showed high removal efficiencies and high biomass respiratory activity. On the other hand, the salinity in…
Sequential batch membrane bio-reactor for wastewater treatment: The effect of increased salinity
2016
In this work, a sequential batch membrane bioreactor pilot plant is investigated to analyze the effect of a gradual increase in salinity on carbon and nutrient removal, membrane fouling and biomass kinetic parameters. The salinity was increased by 2 g NaCl L-1 per week up to 10 g NaCl L-1. The total COD removal efficiency was quite high (93%) throughout the experiment. A gradual biomass acclimation to the salinity level was observed during the experiment, highlighting the good recovery capabilities of the system. Nitrification was also influenced by the increase in salinity, with a slight decrease in nitrification efficiency (the lowest value was obtained at 10 g NaCl L-1 due to lower nitri…
Performance of industrial scale hollow-fibre membranes in a submerged anaerobic MBR (HF-SAnMBR) system at mesophilic and psychrophilic conditions
2013
The aim of this work was to evaluate the effect of temperature on the performance of industrial hollow-fibre (HF) membranes treating urban wastewater in a submerged anaerobic MBR system (SAnMBR). To this end, a demonstration plant with two commercial HF ultrafiltration membrane modules (PURON®, Koch Membrane Systems, PUR-PSH31) was operated at 20, 25 and 33 °C. The mixed liquor total solid (MLTS) level was a key factor affecting membrane permeability (K). K was higher under psychrophilic than mesophilic conditions when operating at similar transmembrane fluxes and MLTS, because the biomass activity of the psychrophilic mixed liquor was lower than the mesophilic mixed liquor. Thus, lower ext…
Effect of preparation method on the properties of poly(methyl methacrylate)/mesoporous silica composites
2019
The preparation method of a polymer composite and the filler loading are amongst the factors that influence the properties of the final composites. This article studies the effect of these factors on the thermal stability and thermal degradation kinetics of poly(methyl methacrylate) (PMMA)/mesoporous silica (MCM-41) composites filled with small amounts of MCM-41. The PMMA/MCM-41 composites were prepared through in situ polymerisation and melt mixing methods, with MCM-41 loadings of 0.1, 0.3, and 0.5 wt.%. The presence of MCM-41 increased the thermal stability of PMMA/MCM-41 composites prepared by melt mixing, but in the case of the in situ polymerised samples, the MCM-41 accelerated the deg…
Removal of algae from biological cultures: a challenge for electrocoagulation?
2014
BACKGROUND In the search for novel technologies for the treatment of urban wastewater, combined anaerobic–algae membrane bioreactors have become a very interesting choice. Recovery of algae produced in these reactors has become the key point to obtain a good economic efficiency with this technology. In this work, electrocoagulation is studied as an alternative for the coarse removal of algae from a biological culture. RESULTS Results demonstrate that the electrochemical technology is a suitable technology for this purpose allowing the removal of more than 90% of the algae without modifying significantly the pH and with an operating cost below 0.04 € m−3. The same general trends are observed…