Search results for "Epoxy"
showing 10 items of 384 documents
13C NMR spectra of eudesmane derivatives
1992
The 13C NMR spectral data of 18 eudesmane derivatives, mainly acids and esters of natural and synthetic origin, are reported, and the γ-effect of the epoxide ring in two diastereoisomeric epoxy esters is discussed.
Weak Interactions Modulating the Dimensionality in Supramolecular Architectures in Three New Nickel(II)-Hydrazone Complexes, Magnetostructural Correl…
2011
Three different ONO donor acetyl hydrazone Schiff bases have been synthesized from the condensation of acetic hydrazide with three different carbonyl compounds: salicylaldehyde (HL(1)), 2-hydroxyacetophenone (HL(2)), and 2, 3-dihydroxybenzaldehyde (HL(3)). These tridentate ligands are reacted with Ni(OOCCF(3))(2)·xH(2)O to yield three new Ni(II) complexes having distorted octahedral geometry at each Ni center: [Ni(L(1))(OOCCF(3))(CH(3)OH)](2) (1), [Ni(L(2))(OOCCF(3))(H(2)O)](2) (2), and [Ni(L(3))(L(3)H)](OOCCF(3))(H(2)O)(1.65)(CH(3)OH)(0.35) (3). The ligands and the complexes have been characterized by elemental analysis and IR and UV-vis spectroscopy, and the structures of the complexes ha…
Exceedingly Fast Oxygen Atom Transfer to Olefins via a Catalytically Competent Nonheme Iron Species
2016
El mateix article està publicat en alemany a l'edició alemanya d' 'Angewandte Chemie' (ISSN 0044-8249, EISSN 1521-3757), 2016, vol. 128, núm. 21, p.6418–6422. DOI http://dx.doi.org/10.1002/ange.201601396 The reaction of [Fe(CF3SO3)2(PyNMe3)] with excess peracetic acid at −40 °C leads to the accumulation of a metastable compound that exists as a pair of electromeric species, [FeIII(OOAc)(PyNMe3)]2+ and [FeV(O)(OAc)(PyNMe3)]2+, in fast equilibrium. Stopped-flow UV/Vis analysis confirmed that oxygen atom transfer (OAT) from these electromeric species to olefinic substrates is exceedingly fast, forming epoxides with stereoretention. The impact of the electronic and steric properties of the subs…
Surface Anisotropy in the Expansion Behavior of Laminated Quasi-Isotropic Composites
1984
Mesure a l'aide d'un extensometre des deformations thermiques superficielles de deux materiaux stratifies resine epoxy-fibre de graphite. Les resultats dependent de la direction de mesure, l'anisotropie superficielle associee est inversement proportionnelle aux dimensions de l'echantillon et proportionnelle au rapport d'anisotropie d'une lamelle isolee. Comparaison avec la theorie des stratifications
Use of linear discriminant analysis applied to vibrational spectroscopy data to characterize commercial varnishes employed for art purposes.
2007
An improvement of methodologies for characterising synthetic resins used in varnishes employed for art purposes has been suggested. Several kinds of standard of the most common polymeric resins (acrylic, vinyl, poly(vinyl alcohol), alkyd, cellulose nitrate, latex, polyester, polyurethane, epoxy, organosilicic, and ketonic) were analyzed by Fourier transform infrared (FTIR) spectroscopy. Synthetic resins characterization is based on the mathematical treatment of their whole spectrum, dividing it in 13 sections, avoiding the one-by-one interpretation of the absorption bands. The mathematical model takes as variables the maximal absorbance of each section, and each synthetic standard resin as …
Benchmarking of strength models for unidirectional composites under longitudinal tension
2018
© 2018 Elsevier Ltd Several modelling approaches are available in the literature to predict longitudinal tensile failure of fibre-reinforced polymers. However, a systematic, blind and unbiased comparison between the predictions from the different models and against experimental data has never been performed. This paper presents a benchmarking exercise performed for three different models from the literature: (i) an analytical hierarchical scaling law for composite fibre bundles, (ii) direct numerical simulations of composite fibre bundles, and (iii) a multiscale finite-element simulation method. The results show that there are significant discrepancies between the predictions of the differe…
Debonding failure mechanisms in prestressed CFRP/epoxy/concrete connections
2014
Abstract This paper presents an investigation on the failure mode in prestress force-release tests of CFRP strips bonded to concrete substrates. Background of the study is the gradient anchorage technique. Firstly, experimental test series are presented. It is shown that considerable differences in failure mechanisms between lap-shear and the before mentioned release tests exist. The study reveals a strong Mode I-influence in the debonding process, compared to a Mode II for lap-shear tests. Secondly, FE simulations with a commercially available software are introduced. It is demonstrated that delamination in a force-release test occurs by a mixed-mode failure over the strip width.
Effect of plasma treatment on the properties of Arundo Donax L. leaf fibres and its bio-based epoxy composites: A preliminary study
2016
Abstract A preliminary investigation about the effect of plasma treatment on the properties of natural fibres extracted from the leaf of the giant reed Arundo Donax L. and their compatibility with a bio-based epoxy resin is performed. To this aim, the influence of plasma treatment on the functional groups and on the thermal behaviour of fibre were investigated using Fourier transform infrared spectroscopy and thermogravimetric analysis. Moreover, the mechanical characterization of fibres was performed through fibre tensile tests. Short randomly oriented fibres/bio-based epoxy composites were manufactured by hand lay-up method followed by compression moulding, varying both fibres weight cont…
Effect of Plasma Treatment on Mechanical and Thermal Properties of Marble Powder/Epoxy Composites
2016
The aim of this work was to study the effect of the plasma treatment on the behavior of composite structures reinforced with marble powder, obtained as processing waste in the “Custonaci” basin. Moreover, different filler amounts (i.e. 10%wt, 20%, 30% in weight) were investigated. For the mechanical characterization, tensile and flexural quasi-static tests, Charpy impact test, and dynamic mechanical thermal analysis (DMTA) were performed. For the thermal stability, thermogravimetric analysis was carried out. Finally, real density and fraction of voids were measured. It was observed that untreated marble powder, on one hand, increases tensile and flexural stiffness and improves thermal stabi…
Incorporation of Silica Nanospherical Particles into Epoxy-Amine Crosslinked Materials
2008
Composites of silica nanospheres coated with crosslinked epoxy–amine were synthesised and examined by 29Si-magic-angle-spinning nuclear magnetic resonance spectroscopy, thermogravimetric analysis, Fourier transform infrared spectroscopy and scanning electron microscopy. The most representative fact is that epoxy-modified nanospheres lost less weight at high temperatures. At temperatures greater than 300°C the loss of weight for epoxy-modified nanospheres was rather lower than for unmodified nanospheres. This helped them to retain their structures, as the loss of weight can have adverse effects on network defects, due to the loss of crosslinks by unit of volume.