Search results for "Extrusion"
showing 10 items of 142 documents
The Relevance of Kneading and Extrusion Parameters in the Manufacture of Active Porous Aluminas from Pseudoboehmites
1987
In order to study the effect-on crushing strength, attrition resistance, specific pore volume, and pore volume distribution of extrudates-of kneading and extrusion parameters in the manufacture of active porous aluminas, a commercial pseudoboehmite (Pural SB from Condea Chemie, Brunsbuttel, FRG) was employed. A minimum kneading torque was required to prepare an extrudable paste, predetermined by extrusion conditions. The torque had an upper limit with respect to certain extrudate properties. The amount of water and the concentration of nitric acid as binder solutions were found to have a decisive bearing on the mechanical properties and the distribution of the pore volume. Crushing strength…
Effect of Water on the Mechanical Behaviour of Extruded Flat Bread
1997
Abstract The effect of water on the mechanical properties of extruded breads was studied, at room temperature. As the moisture content was increased from 6 to 9% moisture, the resistance to fracture (compression tests) or rupture (tensile tests) was improved. Above this moisture range, plasticisation by water was the dominant phenomenon. The brittle to ductile transition was observed to occur within a moisture content range from 9 to 13·7% (w/w). The influence of water on the crispness of extruded bread, evaluated with sensory evaluation, is also described.
Glass Transition and Food Technology: A Critical Appraisal
2002
ABSTRACT: Most low water content or frozen food products are partly or fully amorphous. This review will discuss the extent to which it is possible to understand and predict their behavior during processing and storage, on the basis of glass transition temperature values (Tg) and phenomena related to glass transition. Two main conclusions are provisionally proposed. Firstly, glass transition cannot be considered as an absolute threshold for molecular mobility. Transport of water and other small molecules takes place even in the glassy state at a significant rate, resulting in effective exchange of water in multi-domains foods or sensitivity to oxidation of encapsulated materials. Texture pr…
Comparison of Different Processing Methods to Prepare Poly(lactid acid)–Hydrotalcite Composites
2013
The effect of the compounding method on the morphology and on the properties of poly(lactic acid) (PLA)-hydrotalcite (HT) composites was studied. Moreover, the influence of two different kinds of HT - organically modified (OM-HT) and unmodified (U-HT) - and their concentration was evaluated. The composites were prepared using either a single screw extruder (SSE), a counter rotating twin-screw compounder (TSC) or a corotating twin-screw extruder (TSE). The prepared materials were characterized by scanning electron microscopy, gel permeation chromatography (GPC) analysis, mechanical and rheological measurements. The results indicated that the best morphology, i.e., particles dimension and dis…
Bilayer biodegradable films prepared by co-extrusion film blowing: Mechanical performance, release kinetics of an antimicrobial agent and hydrolytic …
2020
Abstract Bilayer biodegradable, eco-friendly films were prepared by co-extrusion film blowing, coupling polylactic acid (PLA) and Bio-flex ® (BIO). Furthermore, in the PLA layer, carvacrol (CRV) was added as a natural antimicrobial additive, whereas a nanoclay (D72T) was integrated to protect CRV from volatilization and to modulate release. The materials were analyzed by morphological, chemical-physical, mechanical testing. Furthermore, CRV release and degradation tests were performed. The results pointed out that coupling the two matrices allows gathering the stiffness of PLA with the ductility of BIO. Furthermore, the interlayer adhesion is promoted by CRV. D72T exerts a key-role in avoid…
Two Consecutive Magneto-Structural Gas-Solid Transformations in Non-Porous Molecular Materials
2018
Modification of the magnetic properties in a solid-state material upon external stimulus has attracted much attention in the recent years for their potential applications as switches and sensors. Within the field of coordination polymers, gas sorption studies typically focus on porous solids, with the gas molecules accommodating in the channels. Here we present a 1D non-porous coordination polymer capable of incorporating HCl gas molecules, which not only causes a reordering of its atoms in the solid state but also provokes dramatic changes in the magnetic behavior. Subsequently, a further solid-gas transformation can occur with the extrusion of HCl gas molecules causing a second structural…
Recombinant cDNA encapsulation in small liposomes with hepatocyte access ability.
1993
Liposomal encapsulation efficiency of a recombinant cDNA was studied by several procedures. We observed that supernatant fraction of ultracentrifuged liposomes prepared by extrusion through polycarbonate filters of 400 nm pore size yielded a very homogeneous suspension of small (50 nm diameter) unilamellar liposomes with highest DNA/lipid ratio and great ability to access to hepatocytes.
Subtractive versus mass conserving metal shaping technologies: an environmental impact comparison
2015
The scientific studies in the domain of environmental sustainability of metal processing technologies predominantly focus on conventional material removal processes, as milling and turning. Despite some exceptions, many other non-machining technologies, such as metal forming processes, are still not well documented in terms of their energy and resource efficiency. Moreover, to properly evaluate the environmental impact of a given process, a standing-alone approach is no longer sufficient. In order to offer a valuable contribution in the domain of metal shaping sustainability, the present paper proposes a thorough methodology entailing to compare, from the environmental point of view, two tr…
Effectiveness of numerical simulation in avoiding defects in hot extrusion forging products
1999
The hot extrusion forging, in the production of an half shaft of a motorcycle engine, has been analysed by means of finite element simulations. The severe mesh distortion occurring in the simulation has been overcome with the aid of a code provided with automatic remeshing techniques. The study is aimed to promote the use of FEM not only in the designing phase but also as a tool able to investigate defects occurring at the production level.
The Continuous Extrusion Process CONFORM: a full 3D Thermal and Mechanical Analysis
2000
The principle of the Conform extrusion process is based on the action of a rotating wheel that drags and push the feed material by means of the frictional force existing between them. The Conform process has several advantages over the traditional extrusion processes. The preheating phase may be neglected, so that furnaces for heating are not necessary; furthermore, the product is continuous and welding phase of the billets is not required. The influence of three operative parameters, die geometry, velocity and die cooling rate, has been analysed in this paper by means of an “outranking approach” able to give precious indications for the assessment of the process.