Search results for "FORCE"
showing 10 items of 3423 documents
Different sitting positions influence cross country sit skiers performance : Sitting position influence on force generation and cycle characteristics
2018
Cross country sit skiing is a Paralympic discipline in which athletes due to physical impairment ski sitting on a sit-ski. The impairment influences performance directly and also through sitting position. Athletes with a better trunk control usually adopt a sitting position called “kneeing” in which the hip joints are higher than the knee joints. In contrast, athletes with high impact of impairment prefer a sitting position called “knee high” in which the hip joints are lower than the knee joints. Able bodied athletes skiing on the ergometer in these two sitting positions showed different performance. However, to the best of authors’ knowledge, no studies have examined performance, force pr…
Stiffness and Reinforcement Effect of electrical Resistance Strain Gauges
2007
: The increasing use of low-modulus materials, on which the reinforcement effect of the electrical resistance strain gauge is not negligible, has re-opened the research interest into this issue. This study deals with the evaluation of stiffness, and of the strain gauge Young's modulus involved in the estimation of both the global and the local reinforcement effect; the relationship between the strain gauge stiffness and the local reinforcement effect is also analysed. In particular, the experimental technique used to determine the stiffness of some commercial strain gauges is described. The results show that the strain gauge stiffness alone does not permit an accurate evaluation of the loc…
In vivo muscle mechanics during normal locomotion is dependent on movement amplitude and contraction intensity
2001
The effects of movement amplitude and contraction intensity on triceps surae and quadriceps femoris muscle function were studied during repetitive hopping. In vivo forces from Achilles and patellar tendons were recorded with the optic fibre technique from eight volunteers. The performances were filmed (200 Hz) to determine changes in muscle-tendon unit length and velocity. When hopping with a small amplitude (23° knee flexion during the ground contact phase), the Achilles tendon was primarily loaded whereas patellar tendon forces were greater in large-amplitude hopping (56° knee flexion). In spite of the different magnitudes of stretch in the quadriceps femoris muscle, the stretching veloci…
Acupuncture in the treatment of temporomandibular disorders, facial pain, and postural neuromuscular disorders. Presentation of a clinical case
2021
Abstract Background and objectives Temporomandibular disorders have a multifactorial etiology and involve the masticatory muscles, temporomandibular joint and associated structures. Therefore, different treatments are proposed and used. The aim of this paper is the use of acupuncture to treat temporomandibular disorders and associated symptoms. This article presents a clinical case study of a 39-year-old patient who presented temporomandibular disorders and headache of muscular origin. Results After 10 acupuncture sessions, the results were highly satisfactory, with complete relief of headache pain and absence of joint disorders. These results suggest the efficacy of acupuncture in the symp…
Effects of muscle activation on shear between human soleus and gastrocnemius muscles
2017
Lateral connections between muscles provide pathways for myofascial force transmission. To elucidate whether these pathways have functional roles in vivo, we examined whether activation could alter the shear between the soleus (SOL) and lateral gastrocnemius (LG) muscles. We hypothesized that selective activation of LG would decrease the stretch-induced shear between LG and SOL. Eleven volunteers underwent a series of knee joint manipulations where plantar flexion force, LG, and SOL muscle fascicle lengths and relative displacement of aponeuroses between the muscles were obtained. Data during a passive full range of motion were recorded, followed by 20° knee extension stretches in both pass…
Nanoscale mechanical characterization of polymers by atomic force microscopy (AFM) nanoindentations: Viscoelastic characterization on a model material
2009
The Atomic Force Microscope (AFM), apart form its conventional use as a microscope, is also used for the characterization of the local mechanical properties of polymers. In fact, the elastic characterization of purely elastic materials using this instrument can be considered as a well assessed technique while the challenge remains the characterization of the viscoelastic mechanical properties. In particular, one finds the mechanical behavior changing when performing indentations at different loading rates, i.e., on different time scales. Moreover, this apparent viscoelastic behavior can also be due to complex contact mechanics phenomena, with the onset of plasticity and long-term viscoelast…
Developing National Career and Workforce Development Systems and Policies with Structured International Co-operation : Structures, Processes and Acti…
2017
This chapter describes the work undertaken by European Lifelong Guidance Policy Network, ELGPN during 2007-15, including the progress of lifelong guidance policy adaptation and implementation processes of the member countries at national, regional and local levels. In an evaluation of ELGPN’s work, members report that participation in the Network enriched their awareness of possible responses to common challenges and given them fresh perspectives and new insights into their national provision. A key strength of the Network was the strong ownership of its activities expressed by the national delegations. ELGPN member countries stress the importance of continuing structured European co-operat…
Thermal noise limit for ultra-high vacuum noncontact atomic force microscopy
2013
The noise of the frequency-shift signal Δf in noncontact atomic force microscopy (NC-AFM) consists of cantilever thermal noise, tip–surface-interaction noise and instrumental noise from the detection and signal processing systems. We investigate how the displacement-noise spectral density dz at the input of the frequency demodulator propagates to the frequency-shift-noise spectral density dΔf at the demodulator output in dependence of cantilever properties and settings of the signal processing electronics in the limit of a negligible tip–surface interaction and a measurement under ultrahigh-vacuum conditions. For a quantification of the noise figures, we calibrate the cantilever displacemen…
Modification of a commercial atomic force microscopy for low-noise, high-resolution frequency-modulation imaging in liquid environment.
2011
A key issue for high-resolution frequency-modulation atomic force microscopy imaging in liquids is minimizing the frequency noise, which requires a detailed analysis of the corresponding noise contributions. In this paper, we present a detailed description for modifying a commercial atomic force microscope (Bruker MultiMode V with Nanoscope V controller), aiming at atomic-resolution frequency-modulation imaging in ambient and in liquid environment. Care was taken to maintain the AFMs original stability and ease of operation. The new system builds upon an optimized light source, a new photodiode and an entirely new amplifier. Moreover, we introduce a home-built liquid cell and sample holder …
Non-linear analysis of plane steel prestressed truss in fire
2002
The concept of analysis of 2-D static loaded prestressed steel trusses till failure during fire using a modified method of forces is presented. Failure of steel trusses in fire is based on the criterion of stresses. Behaviour of steel is described by non-linear constitutive model (based on hypo-elastic Ramberg-Osgood formula and Dorn creep theory) and Plem proposition (for string). Both models are approximated in calculations by hyperbolic Norton-Bailey rule. Fire simulates thermal force as an action of high temperature that increases linearly up to some level. The complete formulation of this method is illustrated by the algorithm of model parameters identification. Analysis of results for…