Search results for "Fault"

Voltage source inverters: An easy approach for fast fault detection

2013

Fault-tolerant converters have been widely investigated for years and nowadays an extensive technical literature on this field exists. This paper presents a novel fault detection algorithm based on a simple geometrical approach. In the algorithm analysis both the case of faults in single device and the loss of an entire inverter leg have been considered. The proposed methodology is characterized by simplicity, low computational and implementation effort with a consequent fast execution and easy control integration. The suggested algorithm is verified by means of experimental tests and reveals a valid and suitable alternative to the existing state of the art in the field of inverter fault de…

The importance of fracture-healing on the deformation of fluid-filled layered systems

2014

International audience; Understanding the fracturingehealingerefracturing cycle is a fundamental part of studying the deformation dynamics and the permeability evolution of rock systems. Previous studies, however, have not examined the influence of healing i.e. fracture-closure through vein formation and the mechanical properties of the " healed " fractures (veins) on the rock deformation. We present results from a two-dimensional coupled hydro-mechanical model which simulates large time and spatial scale dynamic fracturing and healing of a porous medium under the influence of gravity, tectonic stretching and elevated fluid pressures. Our results show that healing decreases the local porosi…

Reliability Analysis of Three Homogeneous Fault-tolerant Inverter Topologies

2016

Abstract—In this article, non-redundant fault-tolerant inverter topologies are addressed. A novel fault-tolerant control strategy which enhances performances during post-fault operation is proposed. Benefits from the proposed strategy over conventional fault-tolerant topologies are investigated in terms of system reliability. Cost, post-fault performances, and system reliability of the proposed solution are compared with both a conventional triac-based fault-tolerant inverter and a T-type inverter. The reliability analysis of each selected configuration is carried out by means of Markov chains. The analysis is validated through a comparison of reliability and sensitivity curves. As shown by…

Source Mechanisms of Laboratory Earthquakes During Fault Nucleation and Formation

2021

Identifying deformation and pre-failure mechanisms preceding faulting is key for fault mechanics and for interpreting precursors to fault rupture. This study presents the results of a new and robust derivation of first motion polarity focal mechanism solutions (FMS) applied to acoustic emission (AE). FMS are solved using a least squares minimization of the fit between projected polarity measurements and the deviatoric stress field induced by dilatational (T-type), shearing (S-type), and compressional (C-type) sources. 4 × 10 cm cylindrical samples of Alzo Granite (AG, porosity <1%) and Darley Dale Sandstone (DDS, porosity ≈14%) underwent conventional triaxial tests in order to investigat…

SAFETY ANALYSES OF POTENTIAL EXPOSURE IN MEDICAL IRRADIATION PLANTS BY FUZZY FAULT TREE

2008

Bearing fault detection based on time-frequency representations of vibration signals

2015

To prevent failures of a rolling bearing in the gearbox drive system, acceleration sensors are used to detect fault-related signals of the bearing. It is a big challenge to observe and identify signals caused by bearing defects in the time domain or the frequency spectrum by a conventional Fourier analysis. The time-frequency representation of the fault-related signals implemented by the windowed Fourier transform is studied in this work. It is shown that the fault characteristic frequencies can be clearly identified in the time-frequency spectrum if a fault occurs in the bearing of the gearbox at different speeds. Otherwise, the shaft frequency and its multiples are the main harmonics in t…

The Leiza palaeo-fault: Role and importance in the Upper Cretaceous sedimentation and palaeogeography of the Basque Pyrenees (Spain)

1999

Abstract New analysis of the Upper Cretaceous deposits of the Central Depression, a syncline within the Basque Pyrenees, shows that this structure was a deep marine basin analogous to the regional flysch troughs. It was bounded by active faults, including the Leiza palaeo-fault, which sustained erosion of the partly subaerially exposed margins. The Leiza palaeo-fault and its western counterpart, the Kalamua palaeo-fault, are thought to constitute the former plate boundary between Iberia and Europe, and a westward continuation of the North Pyrenean Palaeo-Fault.

Mount Etna: Geochemical signals of magma ascent and unusually extensive plumbing system

2003

] FiveyearsofgasmonitoringfromselectedsitessuggestthatMtEtna’splumbingsystemismuchmoreextensivethanpreviously reported. It extends at least 40 km SW from thevolcano’s boundary along the NE-SW regional fault, whereit discharges about 200 tons/day of gas, containing heliumwith mantle-type isotopic composition. Synchronousvariations of

Recent Activity and Kinematics of the Bounding Faults of the Catanzaro Trough (Central Calabria, Italy): New Morphotectonic, Geodetic and Seismologic…

2021

A multidisciplinary work integrating structural, geodetic and seismological data was performed in the Catanzaro Trough (central Calabria, Italy) to define the seismotectonic setting of this area. The Catanzaro Trough is a structural depression transversal to the Calabrian Arc, lying in-between two longitudinal grabens: the Crati Basin to the north and the Mesima Basin to the south. The investigated area experienced some of the strongest historical earthquakes of Italy, whose seismogenic sources are still not well defined. We investigated and mapped the major WSW–ENE to WNW–ESE trending normal-oblique Lamezia-Catanzaro Fault System, bounding to the north the Catanzaro Trough. Morphotectonic …

Normal vs. strike-slip faulting during rift development in East Africa: The Malawi rift

1992

Kinematic analysis of Neogene and Quaternary faults demonstrates that the direction of extension in the Malawi rift rotated from east-northeast to southeast. Rift development commenced with the formation of half-grabens bounded by northwest-, north-, and northeast-striking normal faults. Owing to slightly oblique rifting, the northwest-striking faults in the northernmost rift segment show a small dextral oblique-slip component, whereas north- and northeast-oriented faults in the central part of the rift display a sinistral oblique-slip component. This first event resulted in block faulting and basin subsidence, which is largely responsible for the present-day basin morphology of Lake Malawi…