Search results for "Fiber"
showing 10 items of 2343 documents
A Non-Invasive Thermal Drift Compensation Technique Applied to a Spin-Valve Magnetoresistive Current Sensor
2011
A compensation method for the sensitivity drift of a magnetoresistive (MR) Wheatstone bridge current sensor is proposed. The technique was carried out by placing a ruthenium temperature sensor and the MR sensor to be compensated inside a generalized impedance converter circuit (GIC). No internal modification of the sensor bridge arms is required so that the circuit is capable of compensating practical industrial sensors. The method is based on the temperature modulation of the current supplied to the bridge, which improves previous solutions based on constant current compensation. Experimental results are shown using a microfabricated spin-valve MR current sensor. The temperature compensati…
A New Method to Measure 3D Textile Defects by Using Dual-lens Camera
2013
International audience; Industrial textile fabric with functionalization always has a high standard requirement. Take polytetrafluoroethylene (PTFE) conveyor belt as an example, the base fabrics must be of first-rate quality, with no weaving faults or broken fibers on coated surface [1]. In a previous work, we have proposed an original method to measure the height of the fiber based on variable homography. This measurement is based on a single camera acquiring two successive frames. This scheme is working well, but measurement depends on conveyor speed used for scrolling fabric. In this paper, we propose an improvement by using a new acquisition device based on two mini-lenses assembled as …
Dimensionless analysis of RC rectangular sections under axial load and biaxial bending
2012
This paper proposes a numerical procedure able to provide ultimate curvature and moment domains of rectangular RC sections subjected to combined axial load and biaxial bending. The formulation is carried out in dimensionless terms in order to give results that are valid for classes of sections characterized by the same values of the geometric and mechanical parameters governing the section response. The role of some of these parameters is investigated here. The results show possible correlations linking the actual values of moment and curvature to the values corresponding to two cases of uniaxial bending to be considered separately. © 2012 Elsevier Ltd.
Fiber laser mode locked through an evolutionary algorithm
2015
Mode locking of fiber lasers generally involves adjusting several control parameters, in connection with a wide range of accessible short-pulse dynamics. In this Letter, we experimentally demonstrate the ability of an evolutionary algorithm to prescribe a set of cavity parameters entailing specific self-starting mode locking. The prescribed parameters are applied to electrically driven polarization controllers, thus shaping the effective nonlinear transfer function at play within the fiber cavity. According to the specifications of the objective function used for the optimization procedure, various short-pulse regimes are obtained. Our versatile method represents an effective novel avenue f…
Effect of FRP Wraps on the Compressive Behaviour of Slender Masonry Columns
2017
In the last decade, Fibre Reinforced Polymer (FRP) wrapping technique has become a common method to retrofit masonry piers or columns with poor structural performances. The passive confinement effect induced by the external wrap allows increasing the compressive strength and ductility of the member. Several studies highlighted as the efficacy of this technique is affected by several key parameters, including the shape of the transverse cross section, stress intensification at the strength corner of sharp sections, amount and mechanical properties of adopted composite. Despite this technique has been widely studied from both theoretical and experimental point of view, most of studies focused…
High-velocity Impact Location on Aircraft panels Using Macro-fiber Composite piezoelectric Rosettes
2010
In this article, an approach based on an array of macro-fiber composite (MFC) transducers arranged as rosettes is proposed for high-velocity impact location on isotropic and composite aircraft panels. Each rosette, using the directivity behavior of three MFC sensors, provides the direction of an incoming wave generated by the impact source as a principal strain angle. A minimum of two rosettes is sufficient to determine the impact location by intersecting the wave directions. The piezoelectric rosette approach is easier to implement than the well-known time-of-flight-based triangulation of acoustic emissions because it does not require knowledge of the wave speed in the material. Hence, th…
Simplified flexural response of steel-fiber reinforced concrete beams
2008
In the present paper, an analytical model is proposed that is able to determine the flexural response of supported beams under four-point bending tests. Cases of normal strength reinforced concrete beams with longitudinal bars in the presence of reinforcing hooked steel fibers and transverse stirrups are considered. A simplified analytical model is presented that is able to calculate the load-deflection curves and the maximum and ultimate deflections occurring in the case of shear or flexure failures. In the case of shear failure, the maximum shear strength of the beams is evaluated by using a recent analytical expression proposed by the author able to account for the shear-to-moment intera…
On the hygrothermal behavior of coconuts fiber insulators on green roofs.
2020
Coconut fibre insulators, represent an insulating material considered as “exotic”, which clashes with the doubts of his thermo-hygrometric behavior, in particular, in the case of covering technology such as green roofs, a technological solution adopted in the case of sustainable buildings or nearly zero energy building. Green roofs represent a valid constructive solution with high thermal performances, adopted in existing and new buildings. The purpose of the research regards the study of the thermo-hygrometric behavior of the concrete and Cross-Laminated Timber (CLT) slabs, insulated with coconut fibre-boards (CF) such as alternative synthetic insulators, referred to 10 different green roo…
Finite element modelling of slipage between FRP rebar and concrete in pull-out test
2014
The paper presents numerical results of direct pull-out test of glass fiber-reinforced polymer (GFRP) rebars embedded in concrete. Rebars of three different cross-sections are considered: circular without longitudinal ribs and with two and four ribs. The design analyses of the rebar configurations embedded in concrete are investigated by the 3D finite element method (FEM), which takes into account the non-linearity using ANSYS software. The results of the numerical model with two ribs were compared with the experimental results. Then, the effect of different rebar geometries to the load-slip pull-out curves was studied. It is concluded that the influence of rib height and width on the pull-…
Label-free wavelength and phase detection based SMS fiber immunosensors optimized with cladding etching
2018
The performance of E-SMS (Etched Singlemode-Multimode-Singlemode) optical fiber structures as immunosensors has been assessed by the implementation of antibody/antigen immunoassays. Through this procedure it has been proven that E-SMS structures are effective and suitable optical platforms for label-free biosensing. Using the phase shift and tracking the wavelength response it was found that the fabricated E-SMS devices exhibited limits of detection (LOD) down up to concentrations of 0.2mg/L of antigens in solution. This was achieved by coating the E-SMS with an antibody-based biolayer (goat IgG) that is able to determine the presence of anti-goat IgG antigen. Both a wavelength detection an…