Search results for "Fiber"

Supercontinuum generation in Ge-doped Y-shaped microstructured tapered fiber

2011

We have investigated the generation of supercontinuum in tapered Y-shaped fibers in the nanosecond pump regime. This fiber used to fabricate the tapers has, in addition, a Ge-doped core which enhances the nonlinearity of the material and the Raman gain. The fiber was pumped at 1064 nm in the ns pump regime (0.6 ns pulses and up to 3.2 kW peak power). The taper had a uniform waist of 0.9 μm diameter and 130 mm length, and the adiabatic transitions were 110 mm long. A flat spectrum spanning from 420 nm to 1870 nm was obtained using a single tapered fiber.

Sub-critical filtration conditions of commercial hollow-fibre membranes in a submerged anaerobic MBR (HF-SAnMBR) system: The effect of gas sparging i…

2012

A submerged anaerobic MBR demonstration plant with two commercial hollow-fibre ultrafiltration systems (PURON®, Koch Membrane Systems, PUR-PSH31) was operated using municipal wastewater at high levels of mixed liquor total solids (MLTS) (above 22gL -1). A modified flux-step method was applied to assess the critical flux (J C) at different gas sparging intensities. The results showed a linear dependency between J C and the specific gas demand per unit of membrane area (SGD m). J C ranged from 12 to 19LMH at SGD m values of between 0.17 and 0.5Nm 3h -1m -2, which are quite low in comparison to aerobic MBR. Long-term trials showed that the membranes operated steadily at fluxes close to the est…

Experimental study of the anaerobic urban wastewater treatment in a submerged hollow-fibre membrane bioreactor at pilot scale

2011

The aim of this study was to assess the effect of several operational variables on both biological and separation process performance in a submerged anaerobic membrane bioreactor pilot plant that treats urban wastewater. The pilot plant is equipped with two industrial hollow-fibre ultrafiltration membrane modules (PURON¿ Koch Membrane Systems, 30m 2 of filtration surface each). It was operated under mesophilic conditions (at 33°C), 70days of SRT, and variable HRT ranging from 20 to 6h. The effects of the influent COD/SO 4-S ratio (ranging from 2 to 12) and the MLTS concentration (ranging from 6 to 22gL -1) were also analysed. The main performance results were about 87% of COD removal, efflu…

Intrapulpal temperature changes during root surface irradiation with an 809-nm GaAlAs laser

2002

The aim of this study was to explore, in vitro, whether the irradiation of human root surfaces with a diode laser might induce nonphysiologic intrapulpal temperature elevations and, therefore, jeopardize pulp vitality.The pulps were removed from human maxillary and mandibular incisors extracted for periodontal reasons. The root canals were enlarged to an apical size #60 file. The teeth were radiographed with standard dental films and a millimeter grid to determine root thickness. The thickness of dentin between the root surface and the pulp in the irradiation areas was 1, 2, and 3 mm. To determine intrapulpal temperature changes during laser irradiation, 0.5-mm K-type thermocouples were ins…

On coverings with special points and monodromy group a Weyl group of type B_d

2014

In this paper we study Hurwitz spaces parameterizing coverings with special points and with monodromy group a Weyl group of type Bd. We prove that such spaces are irreducible if k > 3d ? 3. Here, k denotes the number of local monodromies that are reflections relative to long roots.

Production of hyaluronic acid derivative microfibers with controlled dimension as potential drug delivery system

2015

Mechanical behavior of carbon/flax hybrid composites for structural applications

2012

In this work, the influence of an unidirectional carbon fabric layer on the mechanical performances of bidirectional flax fabric/epoxy composites used for structural applications was studied. Two different bidirectional flax fabrics were used to produce flax fabric reinforced plastic (FFRP) laminates by a vacuum bagging process: one is normally used to make curtains; the other, heavier and more expensive than the previous one, is usually used as reinforcement in composite structures. In order to realize hybrid structures starting from FFRP, an unidirectional UHM carbon fabric was used to replace a bidirectional flax fabric. Tensile and three-point bending tests were performed to evaluate t…

Effects induced by 4.7 eV UV laser irradiation on pure silica core multimode optical fibers investigated by in situ optical absorption measurements

2011

We investigated by in situ optical absorption measurements the effects induced by 4.7 eV UV laser irradiation on pure silica core optical fibers. Laser irradiation with 100 MWcm−2 laser intensity generates in the fiber E′ centers which partially decay after irradiation due to their reaction with diffusing H2. An absorption band peaked at 5.3 eV is observed to grow in the post-irradiation stage with a kinetics anti-correlated to the decay of the 5.8 eV band of the E′ centers. The defect absorbing at 5.3 eV is proposed to be formed by trapping on pre-existing precursors of hydrogen atoms made available by breaking of H2 on E′.We also show by repeated irradiation experiments that the 5.3 eV-ab…

Expression Profile of Stress Proteins, Intermediate Filaments, and Adhesion Molecules in Experimentally Denervated and Reinnervated Rat Facial Muscle

1997

The immunohistochemical profiles of ubiquitin, heat shock protein 70, alpha-B-crystallin, desmin, vimentin, neural cell adhesion molecule (N-CAM), and tenascin in rat facial muscle were studied after permanent denervation by transection of the facial plexus on one side and compared with findings after immediate reinnervation by hypoglossal-facial nerve anastomosis subsequent to transection on the contralateral side. Levator labii muscle samples were collected sequentially at 2, 6, 7, 10, 20, and 24 weeks after surgery. Normal levator labii muscle fibers showed physiological expression of desmin and alpha-B-crystallin. Denervated rat facial muscle displayed distinct up-regulation of ubiquiti…

Analysis of image formation with a photon scanning tunneling microscope

1996

International audience; The photon scanning tunneling microscope (PSTM) is based on the frustration of a total internal reflected beam by the end of an optical fiber. Until now it has been used to obtain topographic information, generally for smooth samples. We report theoretical as well as experimental results on the observation of a step on a quartz substrate with the PSTM. These results demonstrate the effects on image formation of the distance between the fiber tip and the sample surface, the orientation of the incident beam with respect to the step, the polarization, and the coherence of the light. Good agreement exists between numerical simulations and experiments. We show that a pert…