Search results for "GRADE"
showing 10 items of 695 documents
Acousto-optic interaction in biconical tapered fibers: shaping of the stopbands
2016
The effect of a gradual reduction of the fiber diameter on the acousto-optic (AO) interaction is reported. The experimental and theoretical study of the intermodal coupling induced by a flexural acoustic wave in a biconical tapered fiber shows that it is possible to shape the transmission spectrum, for example, substantially broadening the bandwidth of the resonant couplings. The geometry of the taper transitions can be regarded as an extra degree of freedom to design the AO devices. Optical bandwidths above 45 nm are reported in a tapered fiber with a gradual reduction of the fiber down to 70 μm diameter. The effect of including long taper transition is also reported in a double-tapered st…
Parabolic pulse generation with dispersion decreasing optical fiber
2007
We experimentally demonstrate the possibility to generate parabolic pulses via a single dispersion decreasing optical fiber with normal dispersion. We numerically and experimentally outline the influence of the dispersion profile.
Passive compensation of the thermal drift of magnetostriction based Q-switched fiber lasers
2009
Abstract The authors propose and demonstrate a method to compensate the thermal drift of magnetostriction based Q-switched fiber lasers, which is caused by the eddy currents induced in the Terfenol-D magnetostrictive actuators. The consequent wavelength detuning between the fiber gratings of the laser is passively compensated by the use of Monel 400 as thermal actuator of the non-modulated grating. A highly stable pulsed signal is achieved in the range of 1 Hz–5 kHz, with a wavelength detuning between gratings maintained below 10 pm. Furthermore, an optimization of the use of the pump power is proposed, utilizing part of it for simultaneously pumping a fiber optic based amplification stage.
Novel in-line fiber-optic filters and polarisers
2005
Novel in-line devices, based on a tapered fiber whose uniform waist has been metal-coated, are reported. The resonant excitation of a surface plasma mode of the metal film allows for the design of wavelength filters and polarisers
Photonic-crystal fiber-based pressure sensor for dual environment monitoring.
2014
In this paper the development of a side-hole photonic-crystal fiber (SH-PCF) pressure sensor for dual environment monitoring is reported. SH-PCF properties (phase and group birefringence, sensitivity to pressure variations) are measured and compared to simulated data. In order to probe two environments, two sections of the SH-PCF with different lengths are spliced and set in a Solc filter-like configuration. This setup allows obtaining the individual responses of the first and second fiber independently, which is useful for a space-multiplexed measurement. As the employed fiber is sensitive to pressure variations, we report the use of this configuration for dual environment pressure sensing.
<title>Optical pressure sensor based on the side-emitting optical fiber</title>
2003
Two prototype models of pressure sensors using side-scattering optic fiber as the sensitive element have been designed and experimentally assessed. The study showed that the use of 600-micron silica core side-scattering fiber resulted in 5 to 6 times higher sensitivity compared to the oridinary PCS fibers.
Experiments with a fiber-based optical dipole trap for cold Cs-Atoms
2011
Pulling a standard optical fiber to a diameter of less than the wavelength of the guided light causes the light field to project slightly over the fiber boundaries in form of an evanescent wave. The latter can be used for light-matter-interactions in the vicinity of the surface of the fiber and therefore allows to perform quantum optic experiments.
<title>Optical fiber loop sensors</title>
2003
Article presents prepared and tested constructions of loop hybrid fiber optical sensors with light amplitude modulation used for measuring loads and temperature.
Glowing optical fiber designs and parameters
1997
Side-emitting optical fiber designs and main parameters have been studied. A simplified model to describe emission of the 'glowing' fiber is developed. Basic expressions for the emission parameters as functions of the input radiation intensity, distance along the fiber axis and scattering efficiency longitudinal distribution are given for several design modifications. The model assumptions have been checked experimentally by testing silica core side-glowing optical fiber samples.
Optimization of trigeneration systems by Mathematical Programming: Influence of plant scheme and boundary conditions
2015
Abstract The large potential for energy saving by cogeneration and trigeneration in the building sector is scarcely exploited due to a number of obstacles in making the investments attractive. The analyst often encounters difficulties in identifying optimal design and operation strategies, since a number of factors, either endogenous (i.e. related with the energy load profiles) and exogenous (i.e. related with external conditions like energy prices and support mechanisms), influence the economic viability. In this paper a decision tool is adopted, which represents an upgrade of a software analyzed in previous papers; the tool simultaneously optimizes the plant lay-out, the sizes of the main…