Search results for "Humidity"
showing 10 items of 291 documents
Humidity effects on gravitational settling and Brownian diffusion of atmospheric aerosol particles
1977
The dependency on relative humidity of the settling velocity of aerosol particles in stagnant air and of the diffusion coefficient due to Brownian motion of aerosol particles was computed for six aerosol types and different particles sizes in dry state. The computations are based (1) on mean bulk densities of dry aerosol particles obtained from measurements or from the knowledge of the chemical composition of the particles, (2) on micro-balance measurements of the water uptake per unit mass of dry aerosol substance versus water activity at thermodynamic equilibrium, and (3) on measurements of the equilibrium water activity of aqueous sea salt solutions. The results show a significant depend…
Environmental chamber for an atomic force microscope.
2007
A commercial atomic force microscope (AFM), originally designed for operation in ambient conditions, was placed inside a compact aluminum chamber, which can be pumped down to high vacuum levels or filled with a desired gaseous atmosphere, including humidity, up to normal pressure. The design of this environmental AFM is such that minimal intrusion is made to the original setup, which can be restored easily. The performance inside the environmental chamber is similar to the original version.
Molecular Semiconductors — Doped Insulator (MSDI) heterojunctions as new conductometric devices for chemosensing in wet atmosphere.
2015
Most of the gas sensors are based on resistors with inorganic materials and more rarely on other conductometric devices (diodes or transistors). Conductometric sensors have also been designed with molecular materials. Thus, in 2009, Molecular Semiconductor — Doped-insulator (MSDI) heterojunctions were built around a heterojunction between a molecular semiconductor (MS) and a doped-insulator (DI). The MS must be more conductive than the sublayer to take advantage of the heterojunction. The MS is generally of p-type and DI can be of p-type (p-MSDI) or n-type (n-MSDI) material. The energy barrier at the interface depends on the difference in the charge carrier density in the two layers, leadin…
The Influence of Ageing on the Impact Damage of Carbon Epoxy Composites
2011
Abstract This study looks into the influence of ageing on the carbon epoxy composite when impact is applied. Three different stacking sequences were investigated, one sequence with the classic lay-up, whereas the other two have quasi-isotropic and quasi-homogeneous behaviour. The specimens were aged up to 2100 h (3 months) in a climatic chamber with a temperature of 70 °C and relative humidity of 85%. The mass was measured regularly during the hygrothermal ageing treatment. The mass was always measured directly after exiting the climatic chamber and it was noted that for each stacking sequence, the same regular increase in mass is observed until stabilisation. The specimens were then impact…
A plasticity model for predicting the rheological behavior of paperboard
2017
The sorption of water into the paperboard exposes a container to reversible and irreversible deformations under relative humidity variations. In this study, an elasto-plastic material model is used to demonstrate how through-thickness dry solids content gradients can generate permanent in-plane strains in paperboard. The measurements presented in this paper indicate that in consecutive loading-unloading cycles, the yield stress either remains roughly constant or decreases, and an additional permanent set of strain is obtained even when the maximum tension of repetitions stays constant. Two modified approaches concerning elasto-plastic hardening behavior based on the measurements of this wor…
Conducting Polymers for Ammonia Sensing: Electrodeposition, Hybrid Materials and Heterojunctions
2017
International audience; Polyaniline (PANI) with electrodonating and electrowithdrawing substituents were electrodeposited and studied as sensing materials in resistors and heterojunctions. Whereas the dimethoxyaniline leads to a highly conductive material, the tetrafluoroaniline leads to a poor conducting polymer. However, this latter was used in heterojunctions, associated with a highly conductive material, the lutetium bisphthalocyanine LuPc2. Elsewhere, hybrid materials combining polypyrrole (PPy) with ionic macrocycles as counterions were also electrosynthesized and used as sensing material in resistors, for the detection of ammonia. They exhibit a higher sensitivity compared to PPy pre…
Highly Stable Thin Films Based on Novel Hybrid 1D (PRSH)PbX3 Pseudo-Perovskites
2021
In this study, the structure and morphology, as well as time, ultraviolet radiation, and humidity stability of thin films based on newly developed 1D (PRSH)PbX3 (X = Br, I) pseudo-perovskite materials, containing 1D chains of face-sharing haloplumbate octahedra, are investigated. All films are strongly crystalline already at room temperature, and annealing does not promote further crystallization or film reorganization. The film microstructure is found to be strongly influenced by the anion type and, to a lesser extent, by the DMF/DMSO solvent volume ratio used during film deposition by spin-coating. Comparison of specular X-ray diffraction and complementary grazing incidence X-ray diffract…
Effect of ultraviolet and moisture action on biodegradable polymers and their blend
2020
In this work, the suitability of polylactic acid (PLA), polybutylene adipate terephthalate (PBAT) and PBAT/PLA blend samples to outdoor applications were investigated in terms of mechanical, morphological and visual properties in presence of ultraviolet action and water, finding that PLA in particular can be actually considered for such applications.
Effect of relative humidity on carvacrol release and permeation properties of chitosan based films and coating
2014
International audience; The influence of water vapour conditions on mass transport and barrier properties of chitosan based films and coatings were studied in relation to surface and structural properties. Water contact angles, material swelling, polymer degradation temperature, barrier properties (PO2, PCO2, WVP) and aroma diffusion coefficients were determined. The solvent nature and the presence of carvacrol influenced the surface and structural properties and then the barrier performance of activated chitosan films. Increasing RH from 0% to 100% led to a significant increase in material swelling. The plasticization effect of water was more pronounced at high humid environment, while at …
Evaluation of a Real, Low Cost, Urban WSN Deployment for Accurate Environmental Monitoring
2011
There are many areas where Wireless Sensor Networks (WSN) can offer innovative solutions for environmental monitoring applications and the meteorological community, but due to their complexity in terms of energy constraints and low performance devices, very few real deployments can be found. In this paper we will explain in detail the design, implementation and performance evaluation of a sparse WSN that has been working maintenance-free for over 12 months. The network has been designed for environmental monitoring purposes, and several motes, attached to lampposts, accurately measure the Temperature and Relative Humidity at various locations in a local street. Our contribution is an enhanc…