Search results for "INTERFACE"
showing 10 items of 2139 documents
Highly textured boron/nitrogen co-doped TiO2 with honeycomb structure showing enhanced visible-light photoelectrocatalytic activity
2020
International audience; In this work, we report a novel photocatalyst based on boron and nitrogen co-doped TiO2 rutile (1 1 0) honeycomb structures. The photocatalyst has been prepared by simultaneously oxidizing and doping a Ti-foil substrate at 750 degrees C. The unit cell volume and the crystallite size of grown TiO2 films were measured by Rietveld refinement analysis. The co-doping by boron and nitrogen was achieved simultaneously with the oxidation of the titanium, resulting in a rutile (1 1 0) textured TiO2 film. X-ray photoelectron spectroscopy analysis revealed the presence of Ti-O-N and Ti-O-B-N bonds, and the presence of crystal defects in the lattice was detected and displayed by…
Structure and Dynamics of Confined Liquids: Challenges and Perspectives for the X-ray Surface Forces Apparatus
2019
Preprint of the open access article Weiss, H., Cheng, H.-W., Mars, J., Li, H., Merola, C., Renner, F. U., Honkimäki, V., Valtiner, M., & Mezger, M. (2019). Structure and Dynamics of Confined Liquids: Challenges and Perspectives for the X-ray Surface Forces Apparatus. Langmuir, 35(51), 16679–16692. https://doi.org/10.1021/acs.langmuir.9b01215
The HITRAN2016 molecular spectroscopic database
2017
This paper describes the contents of the 2016 edition of the HITRAN molecular spectroscopic compilation. The new edition replaces the previous HITRAN edition of 2012 and its updates during the intervening years. The HITRAN molecular absorption compilation is composed of five major components: the traditional line-by-line spectroscopic parameters required for high-resolution radiative-transfer codes, infrared absorption cross-sections for molecules not yet amenable to representation in a line-by-line form, collision-induced absorption data, aerosol indices of refraction, and general tables such as partition sums that apply globally to the data. The new HITRAN is greatly extended in terms of …
An Information Aggregation and Analytics System for ATLAS Frontier
2019
International audience; ATLAS event processing requires access to centralized database systems where information about calibrations, detector status and data-taking conditions are stored. This processing is done on more than 150 computing sites on a world-wide computing grid which are able to access the database using the Squid-Frontier system. Some processing workflows have been found which overload the Frontier system due to the Conditions data model currently in use, specifically because some of the Conditions data requests have been found to have a low caching efficiency. The underlying cause is that non-identical requests as far as the caching are actually retrieving a much smaller num…
Scanning tunneling microscopy and spectroscopy of Mo clusters grown on TiO2(110).
2007
Molybdenum was deposited in two steps (3 eq. ML and 1 eq. ML) on the light blue rutile TiO2 10) (1 x 1) surface at room temperature, each Mo deposition cycle being followed by an annealing up to 950-1000 K. This procedure was found to lead to formation of separated clusters having a size in very wide range (1-20 nm). Scanning tunneling microscopy showed a dependence of the cluster morphology as a function of the size. The scanning tunneling spectra of Mo clusters was studied as a function of cluster dimensions and discussed in comparison with photoelectron spectroscopy results previously obtained for homogeneous Mo films. The dI/d V curves do not display the valence band structure of deposi…
Evidence for the Existence of an Effective Interfacial Tension between Miscible Fluids: Isobutyric Acid-Water and 1-Butanol-Water in a Spinning-Drop …
2006
We report definitive evidence for an effective interfacial tension between two types of miscible fluids using spinning-drop tensiometry (SDT). Isobutyric acid (IBA) and water have an upper critical solution temperature (UCST) of 26.3 degrees C. We created a drop of the IBA-rich phase in the water-rich phase below the UCST and then increased the temperature above it. Long after the fluids have reached thermal equilibrium, the drop persists. By plotting the inverse of the drop radius cubed (r(-)(3)) vs the rotation rate squared (omega(2)), we confirmed that an interfacial tension exists and estimated its value. The transition between the miscible fluids remained sharp instead of becoming more…
A general strategy to determine the congruence between a hierarchical and a non-hierarchical classification
2007
This article is available from: http://www.biomedcentral.com/1471-2105/8/442
Direct measurements of the effects of salt and surfactant on interaction forces between colloidal particles at water-oil interfaces
2007
The forces between colloidal particles at a decane-water interface, in the presence of low concentrations of a monovalent salt (NaCl) and of the surfactant sodium dodecylsulfate (SDS) in the aqueous subphase, have been studied using laser tweezers. In the absence of electrolyte and surfactant, particle interactions exhibit a long-range repulsion, yet the variation of the interaction for different particle pairs is found to be considerable. Averaging over several particle pairs was hence found to be necessary to obtain reliable assessment of the effects of salt and surfactant. It has previously been suggested that the repulsion is consistent with electrostatic interactions between a small nu…
Integration of PCL and PLA in a monolithic porous scaffold for interface tissue engineering.
2016
A novel bi-layered multiphasic scaffold (BLS) have been fabricated for the first time by combining melt mixing, compression molding and particulate leaching. One layer has been composed by polylactic acid (PLA) presenting pore size in the range of 90-110µm while the other layer has been made of polycaprolactone (PCL) with pores ranging from 5 to 40µm. The different chemo-physical properties of the two biopolymers combined with the tunable pore architecture permitted to realize monolithic functionally graded scaffolds engineered to be potentially used for interface tissues regenerations. BLS have been characterized from a morphological and a mechanical point of view. In particular, mechanica…
Polylactide-based materials science strategies to improve tissue-material interface without the use of growth factors or other biological molecules
2018
In a large number of medical devices, a key feature of a biomaterial is the ability to successfully bond to living tissues by means of engineered mechanisms such as the enhancement of biomineralization on a bone tissue engineering scaffold or the mimicking of the natural structure of the extracellular matrix (ECM). This ability is commonly referred to as "bioactivity". Materials sciences started to grow interest in it since the development of bioactive glasses by Larry Hench five decades ago. As the main goal in applications of biomedical devices and tissue scaffolds is to obtain a seamless tissue-material interface, achieving optimal bioactivity is essential for the success of most biomate…