Search results for "IPM"
showing 10 items of 1361 documents
Structure and thermal properties of a chitosan coated polyethylene bilayer film
2012
The thermal and the structural properties of chitosan coated polyethylene (PE) films were studied. The coating process did not significantly influence the thermal stability and the PE surface structure and/or composition of the polyolefin. Dehydration temperature of chitosan films reflected the strength of water/acetic acid/chitosan chains interactions. Glycerol, used as a plasticizer, formed new hydrophilic centres in the film matrix. Moreover it was better integrated in the CSEGLY than in CSAGLY network. Besides, the addition of a plasticizer in the chitosan films decreased the film degradation temperature. There were two main steps for the PE chitosan coated films degradation. The first …
Effects of pulse current mode on plasma electrolytic oxidation of 7075 Al in Na2WO4 containing solution: From unipolar to soft-sparking regime
2018
Abstract Plasma electrolytic oxidation coatings were produced on 7075 Al alloy in a silicate based solution containing sodium tungstate using unipolar, usual bipolar and soft-sparking bipolar pulsed current regimes. X-ray diffraction proved that the coatings contain gamma alumina and metallic tungsten. EDS results showed that the tungsten content decreases with increasing the negative half cycle. Scanning electron microscopy showed that the pancake and volcano-like were dominant morphologies for the coatings produced by the unipolar and bipolar current regimes, respectively. Under unipolar current regime, a band of large pores is observed at the metal/coating interface, while they became di…
Contactless Nanoparticle-Based Guiding of Cells by Controllable Magnetic Fields
2021
Peter Blümler,1 Ralf P Friedrich,2 Jorge Pereira,3 Olga Baun,1 Christoph Alexiou,2 Volker Mailänder3,4 1Institute of Physics, Johannes Gutenberg-University Mainz, Mainz, 55128, Germany; 2Department of Otorhinolaryngology, Head and Neck Surgery, Section of Experimental Oncology and Nanomedicine (SEON), Else Kröner-Fresenius-Stiftung-Professorship, Universitätsklinikum Erlangen, Erlangen, 91054, Germany; 3Department of Physical Chemistry, Max Planck Institute for Polymer Research, Mainz, 55128, Germany; 4Department of Dermatology, University Medical Center of the Johannes Gutenberg-University Mainz, Mainz, 55131, GermanyCorrespondence: Peter Blümle…
Experimental investigation of Brillouin and Raman scattering in a 2SG sulfide glass microstructured chalcogenide fiber.
2008
International audience; In this work, we investigate the Brillouin and Raman scattering properties of a Ge15Sb20S65 chalcogenide glass microstructured single mode fiber around 1.55 microm. Through a fair comparison between a 2-m long chalcogenide fiber and a 7.9-km long classical single mode silica fiber, we have found a Brillouin and Raman gain coefficients 100 and 180 larger than fused silica, respectively.
Correlation Between the Electrical Properties and the Morphology of Low-Pressure MOCVD Titanium Oxynitride Thin Films Grown at Various Temperatures
2000
Titanium oxynitride (TiN x O y ) thin films were deposited by low-pressure metal-organic CVD (LP-MOCVD) on (100) silicon, sapphire, and polycrystalline alumina substrates. Titanium isopropoxide (TIP) and ammonia were used as precursors. The influence of the growth temperature, ranking from 450°C to 750°C, was investigated by scanning electron microscopy (SEM), and electrical DC measurements. Rutherford back-scattering (RBS) measurements were used to determine the N/O ratio in the films. The surface observations of the deposited films showed two morphological transitions. The resistivity decreased with the growth temperature, while the nitrogen content increased. Moreover, for the highest de…
Improvement of IPMSM performance through a mixed radial-tangential rotor structure
2010
In this paper an IPMSM (Interior Permanent Magnet Synchronous Motor) rotor configuration optimization is proposed in order to increase the performances in terms of torque, limiting at the same time the rotor leakage flux. The final mixed radial and tangential rotor configuration here proposed and described determines a reduction in PM material quantity of about 25% compared to a tangential IPMSM one with the same dimension and weight, together with an increase of the motoring torque of about 50%. Some simulation carried out by using a FEM software and a comparative analysis with two traditional IPMSMs rotor configurations show that a significant improvement can be achieved with limited chan…
Analysis, characterization and minimization of IPMSMs cogging torque with different rotor structures
2015
This paper presents the analysis, characterization and comparison of the cogging torque components generated by five different IPMSM rotor structures. More in detail, an IPMSM model (named IPMSM1), which is derived from a commercial geometry, is analyzed by using a Finite Element Method (FEM) approach. Then, four other IPMSM models, which are obtained by modifying the IPMSM1 rotor structure and by maintaining the same stator configuration, are proposed and analyzed. From the obtained simulation results, the cogging torque components for each structure are determined and compared. From this comparison, a significant cogging torque decrease is occurring for the modified geometries, without af…
Interactions between cells and titanium surfaces.
2002
The interaction between cells and implant materials is determined by the surface structure and/or surface composition of the material. In the past years, titanium and titanium alloys have proved their superiority over other implant materials in many clinical applications. This predominant behaviour is caused by a dense passive oxide layer which forms within milliseconds in oxidizing media. Titanium dioxide layers of 100 nm thickness were produced on the surface of cp-titanium grade 2, and on an experimental alloy of high vanadium content (Ti1.5Al25V) as a harmful control. The layers were produced by thermal and anodic oxidation and by coating by means of the sol-gel process. The resulting o…
Candida albicans biofilms on different materials for manufacturing implant abutments and prostheses
2019
[EN] Background: Morphological, physical and chemical properties of both implants and prostheses can determine the biofilm formation on their surface and increase the risk of biological complications. The aim of this study was to evaluate the capacity of biofilm formation of Candida albicans on different materials used to manufacture abutments and prostheses. Material and Methods: Biofilm formation was analyzed on cp grade II titanium, cobalt-chromium alloy and zirconia, silicone, acrylic resin (polymethylmethacrylate) and nano-hybrid composite. Some samples were partially covered with lithium disilicate glass ceramic to study specifically the junction areas. C. albicans was incubated in a …
Tailoring magnetic properties of electrodeposited thin films of the molecule-based magnet Cr5.5(CN)12 11.5H2O
2012
This paper reports on molecular-based magnetic thin films of Prussian blue analogues (PBA) with high critical temperatures composed of mixed-valence chromium cyanides. The thin films of PBA were synthesized by means of electrodeposition technique. Morphology and magnetic study are presented in a function of electrochemical deposition conditions. We present the electrochemical methods as a promising and effective tool for preparing molecular-based magnetic thin films of Prussian blue analogue.